WORKPRO OPERATOR'S MANUAL
5-TIER STEEL SHELVING UNIT
Product Models
| ITEM NO. | ITEM NAME |
|---|---|
| W082130A | 27.4"X11.7"X60" 5-TIER STEEL SHELVING UNIT |
| W082131A | 35.3"X17.5"X72" 5-TIER STEEL SHELVING UNIT |
Important Information
⚠️ USE PRECAUTION: For your safety.
? INSTRUCTION MANUAL: Read and understand.
? EYE PROTECTION: Must be worn.
? PROTECTIVE GLOVES: Must be worn when assembly.
CAUTION: Read and follow all Safety Rules and Operating instructions before first use of this product. NOTE: Ensure all components are present. If any components are missing, do not proceed with assembly. Please send an email to service@greatstartools.com or call 877-876-7562.
SAVE THIS MANUAL FOR FUTURE REFERENCE
SAFETY INFORMATION
Please read and understand this entire manual before using the product.
CAUTION:
- Do not exceed 330lbs per shelf. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
- Evenly distribute the weight on each shelf, and keep the heaviest loads on the bottom shelf and small lighter items on the upper level.
- Use only on flat, level and hard surface capable of supporting the shelving and any items placed on it.
- Maintain proper footing and balance at all times.
- Keep bystanders out of the area during assembly.
- This product is not a toy. Do not allow children to play with, on or near the unit.
WARNING:
- Do not stand on, step on, or alter this unit for anything outside the designed function of storage.
- Use care when handling and assembling metal plates.
- The metal may have sharp edges or corners. The use of protective gloves is recommended.
- Always remember to use proper lifting techniques when moving the boxed or assembled unit.
COMPONENTS
Ensure all components are present. If any components are missing, do not proceed with assembly.
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Beam | 10 |
| B | Brace | 10 |
| C | Post | 8 |
| D | MDF Board | 5 |
| E | Support Rod | 5 |
| F | Post Coupler | 4 |
| G | Post Foot / Post Cap | 8 |
TOOLS REQUIRED (NOT INCLUDED): Rubber Mallet, Protective Gloves.
Pre-Installation
Before beginning assembly, read through the instructions and make sure all parts are presented. Identify carefully the installation direction of the accessories.
Assembly of this unit is done by fitting the rivets of the beams (A) and braces (B) into the keyhole slots of the posts (C).
Support rods (E) are mounted on beams (A) and braces (B) to lift the shelf load. Finger bend both ends of the support rods (E) to 90 degrees, then bend both ends again by a tool when insert the support rod (E) into beams (A).
The distance between the two adjacent mounting keyholes of the pole is 1-1/2" (38mm).
The height of each layer can be selected and adjusted according to your needs or desired.
The bottom shelf assembly should be installed into the second keyhole slots at the bottom of posts.
The top shelf assembly should be installed into the first keyhole slots at the top of posts.
A rubber mallet may be used to tap down on the top of beams and braces to properly seat the rivets into the narrow end of the keyhole slot.
Attach the post coupler (F) by sliding into the top of the bottom post (C) and locking into key hole position. The end of posts (C) should be in the middle of the post coupler (F).
A visual inspection should be made to ensure that the rivets are properly engaged into the keyhole slot.
In order to protect the floor, the post foot (G) can be covered into the post before installation.
(Fig. a) Keyhole slots face down on post (C) with beam/brace (A/B) rivets.
Shows rivets on beam/brace fitting into keyhole slots on post.
(Fig. b) Assemble the support rod (E) properly.
Step 1: Finger bend both ends of the support rods (E) to 90 degrees.
Step 2: Bend both ends of the support rods (E) again by a tool after inserting the support rod (E) into beams (A).
(Fig. c) Rivets should be seated properly into the slot.
Visual representation of using a mallet to seat rivets.
(Fig. d) The distance between the two adjacent holes is 38mm (1-1/2").
Diagram showing measurement between keyhole slots on a post.
(Fig. e) Assemble the post foot or post cap (G) onto post (C).
Shows post foot/cap being attached to the bottom of a post.
(Fig. f) Post coupler (F) should be seated properly onto the post (C).
The end of posts (C) should be in the middle of the post coupler (F).
Shows post coupler connecting two posts.
ASSEMBLY
Step 1
Slide properly the rivets of beam (A) into posts (C) of your desired location with the narrow end of keyhole slots pointing down and the longer ledge of beam (A) facing up. Tap lightly to seat rivets.
NOTE: Make sure all the rivets are fully seated into the post slots. You may turn to a rubber mallet (not included) for achieving this target. This applies to all the rivets used in this unit.
Diagram showing beam (A) being attached to post (C) with rivets, and then tapping with a mallet.
Step 2
Repeat the previous step 1 to attach beams (A) and brace (B) to posts (C).
NOTE: Each of the beams (A) and braces (B) on the same level should be at the same height. You can adjust to the same height by counting the number of holes.
Finger bend both ends of the support rod to 90 degrees, then insert the ends into the slot of beams (A) completely, then bend to 90 degree by a tool again.
Diagram showing support rod (E) being bent and inserted into beams (A) and braces (B).
Step 3
Add MDF board (D) on the shelf ledge of the level previously built.
Diagram showing MDF board (D) being placed on assembled beams.
Step 4
Repeat the previous steps to attach beams (A) and braces (B) to posts (C) and add MDF boards (D) until the first two levels are assembled.
Diagram showing the first two levels of the shelving unit assembled with MDF boards.
Step 5
Attach the post coupler (F) by sliding into the top of the bottom post (C) and locking into key hole position.
Insert and press down top posts (C) with narrow end of keyhole slots pointing down to the post coupler (F). The end of posts (C) should be in the middle of the post coupler (F).
Diagram showing post coupler (F) connecting bottom post (C) and top post (C).
Step 6
Repeat steps 1-3 to form the third to fifth levels.
The end of posts (C) should be in the middle of the post coupler (F).
Diagram showing the completed 5-tier shelving unit.
Specifications & Support
Maximum Weight Limit: 330 lbs per shelf evenly distributed
Questions, problems, damage or missing parts:
Contact Greatstar Industrial USA, LLC for assistance:
Email: service@greatstartools.com
Phone: 877-876-7562
Distributed by: GREATSTAR INDUSTRIAUSA, LLC
Address: 9836 Northcross Center Court, Suite A, Huntersville, NC 28078, USA
Made in Cambodia
