AKTERSPRING Pendant Lamp
Model: T2405
Important Safety Information
IMPORTANT: Always shut off power to the circuit before starting installation work. In some countries, electrical installation work may only be carried out by an authorized electrical contractor. Contact your local electricity authority for advice. ❗
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or their service agent or a similar qualified person in order to avoid a hazard. If you are uncertain, please contact IKEA.
(Note: This section consolidates safety information from multiple languages present in the original document.)
Parts Included
The following components are included with your AKTERSPRING lamp:
- 1 x Mounting bracket with threaded section
- 1 x Allen key ⚙️
- 3 x Glass shades
- 6 x Small screws (3 + 3)
(Diagram description: The diagram illustrates the components included: one mounting bracket with a threaded section, one Allen key, three glass shades, and six small screws.)
Assembly Instructions
Step 1: Attach Shade Holders
The main circular lamp structure with its wiring is shown. A magnified view demonstrates screwing a threaded component (part of the shade holder) into one of the three attachment points on the lamp ring. This process is repeated three times (3x).
(Diagram description: Shows the main lamp ring structure with wiring and three attachment points. A close-up shows a threaded part being screwed into one of these points.)
Step 2: Secure Shade Holders
The lamp ring now has the three shade holders attached. A magnified view illustrates inserting and tightening a small screw using the Allen key into each shade holder. This is done three times (3x).
(Diagram description: Shows the lamp ring with attached shade holders. A close-up shows a small screw being inserted and tightened with the Allen key into each holder.)
Step 3: Connect Main Power Cable
A hand holds the ceiling canopy and the main power cable. The power cable's connector is being guided into the corresponding fitting on the mounting bracket assembly.
(Diagram description: Shows a hand holding the ceiling canopy and the main power cable, guiding the connector into the mounting bracket.)
Step 4: Insert Connector
The power cable connector is shown being fully inserted into the mounting bracket.
(Diagram description: Shows the power cable connector being fully inserted into the mounting bracket.)
Step 5: Route Wires
The wires are routed through a spring mechanism for strain relief. A magnified view shows the wire passing through the spring.
(Diagram description: Illustrates routing wires through a spring mechanism for strain relief.)
Step 6: Hang the Lamp
The lamp assembly is suspended from a ceiling support using a hook. A measurement indicates a recommended slack of 20-40 mm (3/4" – 1 1/2"). Two people are shown lifting the lamp structure.
(Diagram description: Shows the lamp being hung with a hook, with a measurement for cable slack. Two people are shown lifting the lamp.)
Step 7: Connect Wires to Terminal Block
This step illustrates connecting the lamp's wires to a terminal block, showing the Live (L) and Neutral (N) wire connections. Arrows indicate inserting the wires into the correct terminals.
(Diagram description: Shows connecting Live and Neutral wires to a terminal block.)
Step 8: Secure Wire Connection
The final wire connection is shown being secured with an audible "Click!" to confirm proper engagement.
(Diagram description: Shows the final wire connection being secured with a click.)
Step 9: Final Wire Connections
Details the Live (L) and Neutral (N) wire connections to the terminal block.
(Diagram description: Shows Live and Neutral wire connections to the terminal block.)
Step 10: Final Secure Connection
Shows the final secure connection with an audible "Click!".
(Diagram description: Shows the final secure connection with a click.)
Step 11: Attach Canopy and Shades
The main canopy is pushed upwards towards the ceiling. Magnified views illustrate inserting and twisting the threaded part of each shade holder into its corresponding socket on the lamp ring. A warning advises: "CAUTION! Do not overtighten."
(Diagram description: Shows the canopy being pushed up, and shade holders being twisted into the lamp ring. Includes a warning about overtightening.)
Step 12: Attach Glass Shades
The lamp structure with the canopy attached is shown. Hands are shown screwing the three glass shades onto the respective holders.
(Diagram description: Shows hands screwing the three glass shades onto the lamp holders.)
Step 13: Attach Remaining Glass Shades
This step continues the process of attaching the three glass shades to the lamp.
(Diagram description: Continues the process of attaching the glass shades.)
Step 14: Warning - Incorrect Assembly
Warning: Avoid incorrect assembly. Diagrams show the lamp with wires tangled around the shades and the shades improperly attached, both marked with a cross to indicate these methods are not permitted. ❌
(Diagram description: Displays warning symbols showing incorrect assembly methods, such as tangled wires or improperly attached shades, marked with a cross.)
