AKTERSPRING Pendant Lamp
Model: T2405
Important Information & Safety
[!] Always shut off power to the circuit before starting installation work. In some countries, electrical installation work may only be carried out by an authorized electrical contractor. Contact your local electricity authority for advice.
[!] If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or their service agent or a similar qualified person in order to avoid a hazard. If you are uncertain, please contact IKEA.
Note: This document contains installation instructions in multiple languages. The primary language for this HTML version is English.
Parts List
- 1x Mounting bracket assembly with threaded rod
- 1x Hex key (Allen wrench)
- 3x Spherical lamp shades
- 3x Small screws (plus 3 spares)
Assembly Instructions
Step 1
Prepare the main lamp ring. Insert and screw the threaded components into the designated points on the ring. Repeat for all three points.
Diagram Description: The main lamp ring is shown. Two close-up insets illustrate screwing a threaded component into the ring.
Step 2
Connect the electrical wires. Insert the wires into the designated connectors and secure them using the hex key.
Diagram Description: The lamp ring with electrical connectors is shown. Close-up insets show wires being inserted into connectors and secured with the hex key.
Step 3
Insert the mounting bracket assembly into the ceiling canopy.
Diagram Description: The ceiling canopy and the mounting bracket assembly are shown. A hand is depicted inserting the mounting bracket assembly into the canopy.
Step 4
Secure the mounting bracket assembly within the ceiling canopy.
Diagram Description: Close-up views show the mounting bracket assembly being correctly positioned and secured within the canopy.
Step 5
Route the electrical wires through the mounting bracket and secure them. A magnified inset shows a wire being threaded through a spring-loaded mechanism.
Diagram Description: Wires are routed through the mounting bracket and secured. A magnified inset shows a wire being threaded through a spring-loaded mechanism.
Step 6
With assistance, carefully lift and hang the lamp assembly onto a ceiling hook. Ensure the hook is properly installed and the lamp is securely attached. The distance from the ceiling to the top of the lamp's suspension point should be between 20-40 mm (3/4" - 1 1/2").
Diagram Description: Two people are shown holding the lamp assembly, preparing to hang it. An inset shows a ceiling hook with a measurement indication (20-40 mm / 3/4" - 1 1/2").
Step 7
Connect the electrical wires to the terminal block. Connect the Line (L) wire to the L terminal and the Neutral (N) wire to the N terminal. Ensure connections are secure.
Diagram Description: Shows a terminal block with L (Line) and N (Neutral) markings. Wires are being inserted and secured.
Step 8
Close the terminal block cover until it clicks securely into place.
Diagram Description: The terminal block cover is shown being closed, with a "Click!" indication.
Step 9
Connect the Line (L) and Neutral (N) wires to the appropriate terminals in the connector.
Diagram Description: Shows the terminal block and wire connections again, with L and N labels.
Step 10
Connect the main power connector to the lamp assembly. Ensure it clicks into place.
Diagram Description: Shows the connector being plugged in and secured with a click.
Step 11
Push the ceiling canopy upwards to cover the mounting bracket. Secure the canopy by tightening the threaded component. Caution: Do not overtighten.
Diagram Description: The canopy is shown being pushed up and secured. Magnified insets show tightening a threaded component. Text warnings in multiple languages about not overtightening are present.
Step 12
Install the light bulbs into the sockets on the lamp ring (3x).
Diagram Description: The lamp ring with three sockets is shown. Hands are depicted screwing in light bulbs (3x).
Step 13
Attach the spherical lamp shades to the sockets by screwing them on (3x).
Diagram Description: The spherical lamp shades are shown being attached to the sockets. Arrows indicate screwing them on.
Warnings
[!] Warning: Do not attach decorative items such as garlands to the lamp.
Diagram Description: Diagrams show crossed-out decorative items (like garlands) being attached to the lamp.
