STORKLINTA Chest of 6 Drawers Assembly Instructions

Safety Warnings

⚠️ WARNING

Children have died from furniture tipover. To reduce the risk of furniture tipover:

ALWAYS install the provided anti-tip device. [anti-tip hardware]
NEVER put a TV on this product. [TV icon crossed out]
NEVER allow children to stand, climb, or hang on any drawers, doors, or shelves. [child climbing icon crossed out]
NEVER open more than one drawer at a time. [single drawer opening icon]
DO NOT defeat or remove the drawer interlock system; it is an important stability and safety system. [drawer interlock icon]
Place heaviest items in the lowest drawers.

Tools and Wall Mounting

The following tools and hardware are recommended for assembly and wall mounting:

Tools:

Screwdrivers (Phillips head and flat head) [screwdrivers icon]
Hammer [hammer icon]
Drill [drill icon]
Drill bits: Ø 5/16" (8 mm) and Ø 1/8" (3 mm)

Wall Mounting Hardware Guide:

The supplied screws and plugs can be used with most solid (A) and hollow (B) walls. For solid wood (C), use screws without plugs. If you are uncertain, seek professional advice.

Illustration showing three scenarios for wall mounting:

Scenario A (Solid Wall): Screw insertion into a solid wall with a wall plug (Ø 5/16" or 8 mm, screw length 2 3/4" or 70 mm).
Scenario B (Hollow Wall): Screw insertion into a hollow wall with a wall plug (Ø 5/16" or 8 mm, screw length ≈ 1 1/4" or 30 mm).
Scenario C (Solid Wood): Screw insertion directly into solid wood (Ø 1/8" or 3 mm, screw length ≈ 1 1/4" or 30 mm).

Assembly Steps

Step 1

Attach two base panels (part 155370) to the bottom frame using 30x screws (146114) and cam locks (10102026). A close-up shows inserting a screw and then a cam lock, with a hand turning the cam lock to secure the connection.

Step 2

Connect side panels to the base assembly. Parts involved: 5x cam locks (110126) and 8x cam bolts (118331). A close-up shows inserting a cam bolt and then securing it with a cam lock by turning it.

Step 3

Insert 8x cam bolts (118331) into the side panels. A close-up shows a hand screwing in a cam bolt.

Step 4

Insert 8x wooden dowels (101345) into the top edge of the side panels. A close-up shows a dowel being inserted.

Step 5

Attach two side panels to the base assembly. Hands are shown guiding the panels into place.

Step 6

Attach the back support panel. Parts involved: 4x cam locks (119250) and 4x cam bolts (119252). A close-up shows inserting a cam bolt and then securing it with a cam lock by turning it. An incorrect method is crossed out.

Step 7

Assemble the main frame by connecting the side panels and back support. The structure is taking shape.

Step 8

Attach the top panel. Parts involved: 4x cam locks (119250) and 4x cam bolts (119252). A close-up shows inserting a cam bolt and then securing it with a cam lock by turning it. An incorrect method is crossed out.

Step 9

Attach two brackets (102553) to a long support piece (155370) using 2x screws (105248). A close-up shows a hand screwing in a bracket. The long support piece is then attached to the main frame.

Step 10

Attach a bottom support rail to the main frame using 2x screws (105248). An arrow indicates upward movement.

Step 11

Attach drawer slide components. Parts involved: 2x drawer slide brackets (10101849) and 2x drawer front attachments (158568). Close-ups show how to attach these components.

Step 12

Place a large panel onto the partially assembled frame. A close-up shows how the panel fits into a groove.

Step 13

Secure the panel from Step 12 using 2x screws (151707) and 2x drawer slide parts (151708). Close-ups show the insertion of these parts.

Step 14

Attach the back panel to the main frame. Parts involved: 4x wooden dowels (101345). A close-up shows a dowel being inserted into the back panel.

Step 15

Attach a bottom panel to the frame using 6x cam bolts (118331). A close-up shows a hand screwing in a cam bolt.

Step 16

Attach another panel using 2x wooden dowels (101345). A close-up shows a dowel being inserted.

Step 17

Attach drawer slides to the frame. Parts involved: 2x screws (151931) and 2x drawer slide components (10102042). A close-up shows the attachment. An incorrect method is crossed out.

Step 18

Attach drawer slides to the frame. Parts involved: 2x screws (151931) and 2x drawer slide components (10102042). A close-up shows the attachment. An arrow indicates the direction of movement.

Step 19

Attach a back panel to the base of the unit using screws.

Step 20

Attach drawer slide components. Parts involved: 2x cam locks (110126). A close-up shows inserting a cam lock and turning it. Incorrect methods are crossed out.

Step 21

The main cabinet structure with shelves and drawer slides is shown. The top part of the cabinet is being attached.

Step 22

Attach drawer slide components to the cabinet. Parts involved: 4x cam locks (119250) and 4x cam bolts (119252). Close-ups show insertion and rotation. Incorrect methods are crossed out.

Step 23

Attach the cabinet doors. Parts involved: 8x plastic connectors (10093081, 10093082). Close-ups show how to attach these connectors.

Step 24

Insert a drawer into the cabinet. An arrow indicates the direction.

Step 25

Attach drawer slide components to the assembled drawers. Parts involved: 4x drawer slide parts (151708, 151707). Close-ups show the attachment.

Step 26

Attach the anti-tip bracket to the top of the cabinet. Parts involved: 1x screw (100823), 1x screw (109049), and the anti-tip bracket (106989). A close-up shows the assembly.

Step 27

Attach the anti-tip device to the wall. A close-up shows the bracket being secured. An info symbol indicates information.

Step 28

Final attachment of the anti-tip device to the wall. A close-up shows the mechanism for securing the strap.

Step 29

Position the chest of drawers against the wall. An arrow indicates it should be moved towards the wall. 'X' marks on the wall indicate potential drilling points.

Step 30

This step provides a detailed guide on wall mounting, reiterating the use of screws and plugs for different wall types (A, B, C). It includes dimensions for screw lengths and drill hole sizes.

Step 31

Attach the anti-tip strap to the furniture. Part involved: 1x screw (109048). A close-up shows the strap being secured.

Step 32

Attach the anti-tip strap to the wall bracket. Parts involved: 1x screw (109048) and 1x screw (100823). Close-ups show the mechanism and rotation.

Step 33

Final adjustments to the anti-tip strap. Parts involved: 1x screw (109048) and 1x screw (100823). Close-ups show the mechanism and rotation.

Step 34

Assemble drawer bases. Two types of drawer boxes are shown: 2x smaller boxes and 4x larger boxes. A drawer base is assembled using 4x cam bolts (118331).

Step 35

Assemble drawer sides using 4x wooden dowels (101345) for each drawer base.

Step 36

Attach drawer side panels to a drawer base using 4x cam bolts (118331).

Step 37

Attach drawer side panels to a drawer base.

Step 38

Assemble drawer sides using 4x cam locks (120076).

Step 39

Attach a drawer back panel.

Step 40

Attach a drawer handle or support piece (10040242) to a drawer front.

Step 41