Assembly Instructions

Parts List

• Part A: Flat rectangular panel, Quantity: 1 pc.
• Part B: Rectangular frame, Quantity: 2 pcs.
• Part CL: Tall, narrow panel with pre-drilled holes, labeled "Front", Quantity: 1 pc.
• Part CR: Tall, narrow panel with pre-drilled holes, labeled "Front", Quantity: 1 pc.
• Part D: Long, rectangular beam with grooved edges, Quantity: 1 pc.
• Part E: Long, rectangular beam with grooved edges, Quantity: 1 pc.
• Part F: Long, rectangular beam with grooved edges, Quantity: 1 pc.
• Part G: Set of vertical slats, Quantity: 2 pcs.
• Part H: Flat rectangular panel, Quantity: 1 pc.
• Part I: Rectangular frame, Quantity: 1 pc.
• Part JL: Tall, narrow panel with pre-drilled holes, labeled "Front", Quantity: 1 pc.
• Part JR: Tall, narrow panel with pre-drilled holes, labeled "Front", Quantity: 1 pc.
• Part K: Long, narrow metal rail, Quantity: 1 pc.
• Part L: Long, rectangular beam with grooved edges, Quantity: 1 pc.
• Part M: Long, rectangular beam with grooved edges, Quantity: 1 pc.
• Part N: Long, narrow metal rail, Quantity: 1 pc.
• Part O: Set of vertical slats, Quantity: 2 pcs.
• Part P: Rectangular panel with drawer slides, Quantity: 1 pc.
• Part Q: Set of vertical slats, Quantity: 1 pc.
• Part R: Long, narrow metal rail, Quantity: 1 pc.
• Part S: Rectangular panel with drawer mechanism, Quantity: 1 pc.

Hardware List

• Item 1: [Allen key], Quantity: 1 pc.
• Item 2: [Screw 6x30mm], Quantity: 49 pcs + extra 3 pcs.
• Item 3: [Screw 6x16mm], Quantity: 39 pcs + extra 3 pcs.
• Item 4: [Dowel 8x30mm], Quantity: 16 pcs + extra 2 pcs.
• Item 5: [Screw 4x30mm], Quantity: 6 pcs + extra 1 pc.
• Item 6: [Screw 3x15mm], Quantity: 46 pcs + extra 3 pcs.
• Item 7: [LED light], Quantity: 1 pc.
• Item 8: [Screwdriver], Quantity: 1 pc.
• Item 9: [Screw 15x20mm], Quantity: 6 pcs.
• Item 10: [Bracket 20x80mm], Quantity: 2 pcs.
• Item 11: [Screw 4x20mm], Quantity: 4 pcs.
• Item 12: [Cable clip], Quantity: 1 pc.

Assembly Steps

Step 1: Assemble Base Frame

Attach panels CL to beams D, E, and F. Secure using dowels (4) and screws (2). Use the Allen key (1) and screwdriver (8) as shown in the diagrams.

Step 2: Attach Shelves

Connect shelves B to the side panels CL and CR. Secure with screws (2) and washers (3) using the Allen key (1).

Step 3: Attach Second Side Panels

Attach panels CR to the structure. Use screws (2), dowels (4), and screws (5). Ensure proper alignment and use the Allen key (1) and screwdriver (8).

Step 4: Attach Top Panel

Place the top panel A onto the assembled structure. Secure it from underneath using screws (2) with the Allen key (1).

Step 5: Attach Top Frame

Attach the top frame structure (likely part B or similar) to the top panel A and side panels. Use screws (2) and washers (3) with the Allen key (1).

Step 6: Attach Side Slats

Attach the vertical slats G to the sides of the main structure. Use screws (6) and the screwdriver (8).

Step 7: Install LED Light

Install the LED light (7). Connect the wires of the lamp to the home wires using cable clips (12). Ensure power is off before proceeding. Textual description: "First, turn off the power at home. After turning off the power, put on insulating gloves to handle it. Connect the wires of the lamp and the wires at home through component #12 (insert several wires into the slot of component #12), and you can use it."

Step 8: Attach Drawer Slides and Base

Attach panels JL and M to the base structure. Secure using screws (2), dowels (4), and screws (1). Use the Allen key (1) and screwdriver (8).

Step 9: Attach Drawer Rails

Attach metal rails K and N to panels JL and JR. Secure with screws (2), dowels (4), and screws (5). Use the Allen key (1) and screwdriver (8).

Step 10: Attach More Side Panels

Attach panels JR and M to the structure. Secure with screws (2) and dowels (4) using the Allen key (1).

Step 11: Attach More Drawer Rails

Attach metal rails K and N to panels JR and JL. Secure with screws (2), dowels (4), and screws (5). Use the Allen key (1) and screwdriver (8).

Step 12: Attach Drawer Supports

Attach support rails L and I to panels JL and JR. Secure with screws (2) and washers (3) using the Allen key (1).

Step 13: Attach Drawer Panels

Attach panels L and N to the structure. Secure with screws (2) using the Allen key (1).

Step 14: Secure Drawer Components

Attach brackets (9) to panels JL and JR. Secure with screws (9) using the screwdriver (8).

Step 15: Attach Top Shelves/Panels

Attach top panels H to the structure. Secure using screws (2) and washers (3) with the Allen key (1).

Step 16: Attach Rear Slats

Attach the vertical slats O to the rear of the main structure. Use screws (6) and the screwdriver (8).

Step 17: Attach Front Slats

Attach the vertical slats Q to the front base of the unit. Secure with screws (2) and washers (3) using the Allen key (1), and then use screws (9).

Step 18: Attach Sliding Door Rails

Attach metal rails K and R to panels JL and JR. Secure with screws (2) and washers (3) using the Allen key (1).

Step 19: Attach Drawer Fronts/Panels

Attach panels S to the structure. Secure with screws (2) and washers (3) using the Allen key (1).

Step 20: Final Assembly

Attach the remaining vertical slats G to the main structure. Use brackets (10) and screws (11) with the screwdriver (8).