ASSEMBLY INSTRUCTIONS
Storage Cabinet
Thank you for purchasing our product!
Please refer and use this assembly instruction to assemble the product.
Contact our customer service department in case there are any missing or damage parts or hardware. Please also tell us your "Order ID", We will solve for you as soon as possible.
Assembly Preparation
- Remove all packaging materials, staples and packing straps from the carton.
- Refer to Parts List and Hardware List and ensure they are correct before assembly. Contact customer service for missing parts.
- Place all wooden parts on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting scratched.
Safety Precaution
- Keep all hardware parts out of reach of children.
- Dispose plastic packaging material immediately to avoid any risk of suffocation to children and animals.
Tips for Assembly
- Allow ample room for assembly and in close proximity to where product will be placed.
- Assemble the product on a surface that does not scratch or damage the exterior gloss and finish of the furniture.
- Identify all of the parts, hardware and quantities required for each step.
- During assembly, do not over-tighten any fittings as this may cause damage.
- DO NOT USE POWER TOOLS TO ASSEMBLE THIS PRODUCT.
- Always place the product on a flat, level surface.
- Do not sit or stand on the partially assembled product; only use the product for which it is intended.
Care and Maintenance
- Use a slightly damp cloth to clean the product. Do not use bleach or abrasive cleaning material.
- Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is damaged or broken.
- Never allow any kind of liquid to remain on your furniture. Absorption can cause wood to warp or delaminate.
- Do not place hot items (e.g. hot drinks) directly onto the wood surface.
Part List
Please check if all the pieces listed below are received.
Diagram shows an exploded view of the cabinet components, labeled numerically from 1 to 23. Key parts include side panels (1, 2), back panels (3), shelves (4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15), drawer fronts (23), and drawer components (16, 17, 18, 19, 20, 21, 22).
Hardware List
Please check if all the pieces listed below are received.
| Item | Description | Quantity | Visual |
|---|---|---|---|
| A | Cam bolt | 172pcs | [cam bolt icon] |
| B | Cam lock | 172pcs | [cam lock icon] |
| C | Screw | 86pcs | [screw icon] |
| D | Long screws | 12pcs | [long screw icon] |
| E | Short slide rail | 18pcs | [slide rail icon] |
| F | Plastic wedge | 12pcs | [wedge icon] |
| G | Anti-dumping accessories | 2pcs | [anti-tilt icon] |
| H | Light strip | 1pcs | [light strip icon] |
| H | Remote control | 1pcs | [remote control icon] |
| I | Charging station | 1pcs | [charging station icon] |
| J | Hexagon screwdriver | 1pcs | [hexagon screwdriver icon] |
| K | Screwdriver | 1pcs | [screwdriver icon] |
Assembly Requirements
- Assembly Time (Approximate): 4-5 Hours
- 2-Person Assembly
Tools Required (Not Provided)
- Mark Pencil
- Power Drill
Cam Lock System Operation
NOTE: When inserting the Cam Lock, make sure that the Open End of the Cam Lock faces the Cam Screw Entry. The Dowel will be inserted in the hole NEXT to the Cam Lock/Cam Screw Hole.
NOTE: The Cam Lock is backwards in this illustration. The Cam Screw can not connect to the Cam Lock because the Dowel is in the incorrect hole.
NOTE: To tighten, turn the Cam Lock CLOCKWISE until the arrow points AWAY from the connected Panel.
NOTE: DO NOT USE AN AUTOMATIC SCREWDRIVER TO TIGHTEN CAM LOCKS, DO NOT OVER-TIGHTEN.
Diagrams illustrate the correct and incorrect insertion of cam locks and cam bolts, and the clockwise turning motion to secure them.
Drawer Rail Preparation
Before installing the drawer rail, you need to separate the E1 and E2 first.
STEP 1: Extend Slider
Diagram shows extending the drawer slide.
STEP 2: Push Lever Up
Diagram shows pushing a lever up to release the slide components.
STEP 3: Remove Runner
Diagram shows separating the inner runner (E2) from the outer mount (E1).
Labels: E1 Installed on the cabinet, E2 Mounting on drawers.
Assembly Steps
Step 1
I. Use screws (C) to secure the slide rail (E1) to the panel (1,3), and tighten them with a screwdriver. Note: For the correct orientation of slide rail (E1), please refer to the image (front and back).
Diagram shows panels 1 and 3 with slide rails (E1) being attached using screws (C). Orientation indicators (front/back, back plate groove) are shown.
Hardware: C x12, E1 x6.
Step 2
I. Screw in cam-bolt (A) into the designated holes on panel (1,3).
Diagram shows cam-bolts (A) being screwed into panels 1 and 3.
Hardware: A x20.
Step 3
I. Use screws (C) to secure the slide rail (E1) to the panel (2), and tighten them with a screwdriver. Note: For the correct orientation of slide rail (E1), please refer to the image (front and back).
Diagram shows panel 2 with slide rails (E1) being attached using screws (C). Orientation indicators are shown. A 180° rotation symbol is present.
Hardware: C x24, E1 x12.
Step 4
I. Screw in cam-bolt (A) into the designated holes on panel (2). Note: Install cam-bolt (A) on panel 2, please use a manual screwdriver. It is not recommended to use an electric screwdriver.
Diagram shows cam-bolts (A) being screwed into panel 2. An icon indicates using a manual screwdriver (✔️) and not an electric one (❌).
Hardware: A x40.
Step 5
I. Attach panel (4,5,6,6,6) to panel (3), insert cam-lock (B) into the panel (4,5,6,6,6), then turn clockwise to lock onto cam-bolt.
Note: The direction of installing cam-lock (B) is shown in the figure.
Diagram shows panels 4, 5, and multiple 6s being attached to panel 3, with cam locks (B) being inserted and turned.
Hardware: B x10.
Step 6
I. Install panel (23) as per diagram and slide them into the grooves until they are fully seated.
Diagram shows panel 23 being slid into grooves.
Step 7
I. Attach panel (2) to panel (4,5,6,6,6,23), insert cam-lock (B) into the panel (4,5,6,6,6), then turn clockwise to lock onto cam-bolt.
Diagram shows panel 2 being attached to the partially assembled structure, with cam locks (B) being used.
Hardware: B x10.
Step 8
I. Attach panel (4,5,6,6,6) to panel (2), insert cam-lock (B) into the panel (4,5,6,6,6), then turn clockwise to lock onto cam-bolt.
Note: The direction of installing cam-lock (B) is shown in the figure.
Diagram shows panels 4, 5, and multiple 6s being attached to panel 2, with cam locks (B) being inserted and turned.
Hardware: B x10.
Step 9
I. Install panel (23) as per diagram and slide them into the grooves until they are fully seated.
Diagram shows panels 23 being slid into grooves.
Step 10
I. Attach panel (2) to panel (4,5,6,6,6,23), insert cam-lock (B) into the panel (4,5,6,6,6), then turn clockwise to lock onto cam-bolt.
Diagram shows panel 2 being attached to the structure, with cam locks (B) being used.
Hardware: B x10.
Step 11
I. Attach panel (4,5,6,6,6) to panel (2), insert cam-lock (B) into the panel (4,5,6,6,6), then turn clockwise to lock onto cam-bolt.
Note: The direction of installing cam-lock (B) is shown in the figure.
Diagram shows panels 4, 5, and multiple 6s being attached to panel 2, with cam locks (B) being inserted and turned.
Hardware: B x10.
Step 12
I. Install panel (23) as per diagram and slide them into the grooves until they are fully seated.
Diagram shows panels 23 being slid into grooves.
Step 13
I. Attach panel (1) to panel (4,5,6,6,6,23), insert cam-lock (B) into the panel (4,5,6,6,6), then turn clockwise to lock onto cam-bolt.
Diagram shows panel 1 being attached to the structure, with cam locks (B) being used.
Hardware: B x10.
Step 14
I. Install panel (23,23,23) as per diagram and slide them into the grooves until they are fully seated.
Diagram shows three panels labeled 23 being slid into grooves.
Step 15
I. Screw in cam-bolt (A) into the designated holes on panel (14).
II. Attach panel (12,13) to panel (14), insert cam-lock (B) into the panel (12,13), then turn clockwise to lock onto cam-bolt.
Diagram shows panels 12, 13, and 14 being assembled using cam bolts (A) and cam locks (B).
Hardware: A x4, B x4.
Step 16
I. Attach the assembled panel (12,13,14) to panel (15), insert cam-lock (B) into the panel (12,13,14), then turn clockwise to lock onto cam-bolt.
Diagram shows the assembly from Step 15 being attached to panel 15 using cam locks (B).
Hardware: A x8, B x8.
Step 17
I. Screw in cam-bolt (A) into the designated holes on panel (8,11).
II. Attach panel (7,10) to panel (11), insert cam-lock (B) into the panel (7,10), then turn clockwise to lock onto cam-bolt.
III. Attach panel (8) to panel (7,10), insert cam-lock (B) into the panel (7,10), then turn clockwise to lock onto cam-bolt.
Note: This hole is an outlet hole, which is installed on the left as shown in the figure.
Diagram shows panels 7, 8, 10, and 11 being assembled using cam bolts (A) and cam locks (B).
Hardware: A x8, B x8.
Step 18
I. Stick the light strip (H) on the panel (7,8,10,11).
II. Clip the plastic clip (H) to the light strip (H) and stick it to the panel to make the light strip stick firmly to the panel.
Diagram shows a light strip (H) being attached to the inside of the assembled section using clips (H).
Hardware: H x4 (clips), H x1 (light strip).
Step 19
I. Attach the assembled panel (7,8,10,11) to panel (15), insert cam-lock (B) into the panel (7,8,10,11), then turn clockwise to lock onto cam-bolt.
Note: As shown in the figure, panel (8) and panel (14) are in the same direction.
Diagram shows the assembly from Step 17/18 being attached to panel 15 using cam locks (B).
Hardware: A x12, B x12.
Step 20
II. Attach panel (9) to panel (7,8,10,11), using screw (D) attach panel (9) to panel (7,8,10,11) and tighten them with (J) Hexagon screwdriver.
Note: The grooves on the panel (9) are in this direction and in the same direction as the panel (11).
Diagram shows panel 9 being attached to the structure using screws (D) and a hexagon screwdriver (J).
Hardware: D x10.
Step 21
I. Screw in cam-bolt (A) into the designated holes on panel (9).
Diagram shows cam-bolts (A) being screwed into panel 9.
Hardware: A x8.
Step 22
I. Attach the assembled panel (7,8,9,10,11,12,13,14,15) to panel (1,2,2,3), insert cam-lock (B) into the panel (1,2,2,3), then turn clockwise to lock onto cam-bolt.
Diagram shows the main cabinet structure being attached to the base panels (1, 2, 2, 3) using cam locks (B).
Hardware: B x12.
Step 23
I. Fix the charging station (I) to the panel (15) with screws (C).
Diagram shows the charging station (I) being attached to the top panel (15) using screws (C).
Hardware: C x2, I x1.
Step 24
I. Fix the charging station (I) to the panel (15) with screws (C).
Diagram shows the charging station (I) being attached to the top panel (15) using screws (C) and plastic wedges (F).
Hardware: C x12, F x12.
Step 25
I. Screw in cam-bolt (A) into the designated holes on panel (16,18,20,21,22).
II. Attach panel (16,18) to panel (17), insert cam-lock (B) into the panel (17), then turn clockwise to lock onto cam-bolt.
III. Install panel (19) as per diagram and slide them into the grooves until they are fully seated.
IV. Attach panel (20 or 21 or 22) to panel (16,18,19), insert cam-lock (B) into the panel (16,18), then turn clockwise to lock onto cam-bolt.
Diagram shows the assembly of a drawer using panels 16, 17, 18, 19, and drawer front/bottom (20, 21, 22). Cam bolts (A) and cam locks (B) are used.
Hardware: A x72, B x72.
Step 26
I. Use screws (C) to secure the slide rail (E1) to the panel (16,18), and tighten them with a screwdriver.
Note: For the correct orientation of slide rail (E1), please refer to the image (front and back).
Diagram shows slide rails (E1) being attached to drawer panels (16, 18) using screws (C). Orientation indicators are shown.
Hardware: C x36, E1 x18.
Step 27
I. Install the assembled drawer on the cabinet.
Note: Please install the panel (21) of the assembled drawer on the right as shown in the figure, and install the panel (22) of the assembled drawer on the middle, and install the panel (20) of the assembled drawer on the left.
If drawer 20 and drawer 22 and drawer 21 are not aligned vertically, you can adjust this screw (C) to align them: you can first use a screwdriver to loosen the screw (C), then move the panels (16,18) upward or downward, and then use a screwdriver to tighten the screw (C).
Diagram shows assembled drawers being inserted into the cabinet. It also shows a close-up of adjusting screws (C) for alignment and a diagram illustrating the alignment of drawer slide rails (E2) with cabinet slide rails (E1).
Step 28
I. Install anti-tilt accessories: As shown in the figure, use short screws (G) to fix 2 pieces of plastic sheet to the panel (9).
Diagram shows anti-tilt brackets (G) being attached to the back of the cabinet top panel (9) using screws.
Hardware: G x2.
Step 29
I. Mark the drill position on the wall with a pencil.
II. Drill a small hole on the marked position.
III. Insert the plastic peg into the drilled hole.
IV. Fix the plastic sheet to the plastic peg with a long screw.
Diagram shows marking a wall, drilling, inserting wall plugs, and attaching brackets with screws.
Hardware: G x2 (referring to anti-tilt kit components).
Step 30
I. Use plastic strips to connect the plastic plate on the panel (9) to the plastic plate on the wall.
Diagram shows plastic straps connecting the anti-tilt bracket on the cabinet to the bracket on the wall.
Hardware: G x2 (referring to plastic straps).
