Reedog RS11 Ultrasonic 2-in-1 Dog Training Collar

1. Important Safety Information

WARNING

Do not use with aggressive dogs. If your dog exhibits aggression or tendencies towards aggression, this product may cause severe injury or death to the owner and others. If you are unsure whether this product is suitable for your dog, consult a veterinarian or certified trainer.

Regarding Ultrasonic Sound: Do not use the remote transmitter within 12 inches (30 cm) of a human ear when operating in ultrasonic mode.

For use on dogs over 6 months of age and weighing over 8 lbs.

DO NOT use when the dog or collar is wet.

DO NOT press and hold the impulse or vibration button for more than 10 seconds to avoid physical or psychological injury to your dog.

• Your dog should NOT yelp or panic during stimulation. If this happens, the stimulation level is too high; return to the previous level and repeat the process.
• DO NOT charge the device near flammable substances.
• For dog use ONLY. Do not use on children.
• This is not a toy and should only be operated by a responsible adult.

CAUTION

Please read and follow the instructions in this manual carefully before starting training. The following precautions will help ensure your dog's safety and comfort. Millions of dogs are comfortable wearing collars, while some are sensitive to pressure from the contacts.

• It is extremely important that both you and your dog remain safe while learning to walk on a leash. Your dog should be on a strong leash (do not attach it to the receiver). The leash should be long enough for the dog to chase an obstacle but short enough to prevent it from reaching roads or other hazards. You must also be physically strong enough to restrain your dog if it tries to chase.
• Risk of skin damage. Proper fit of the receiver is important. A receiver worn too long or too tightly on the dog's neck can cause skin damage. From redness to pressure sores, this condition is commonly known as pressure sores.
• DO NOT leave the receiver on the dog for more than 12 hours per day.
• If possible, change the position of the receiver on the dog's neck every 1-2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never attach an additional leash to the receiver, as this will cause excessive pressure on the contacts.
• Weekly, clean the dog's neck area and the metal electrodes of the receiver with a damp cloth.
• Daily, check the contact area for any signs of rash or wound.

If a rash or wound appears, discontinue use of the receiver until the skin has healed. If the condition persists for more than 48 hours, consult a veterinarian.

The receiver meets IP67 water resistance standard and can be submerged in water up to 1 meter for a maximum of 30 minutes. Do not use it if submerged or wet.

2. Package Contents

The package typically includes:

• Remote Transmitter (Pilot)
• Receiver (Odbiornik)
• Collar Strap (Pasek na obrożę)
• Metal Contacts (Metalowe elektrody)
• Silicone Conductive Covers (Nakładki silikonowe przewodzące)
• Test Bulb (Żarówka testowa)
• Charging Cable (Kabel ładujący)
• Wrist Strap (Pasek na nadgarstek)

Note: Charger, power bank, and other charging devices shown in illustrations may not be included.

3. Product Overview

Remote Transmitter

The remote transmitter features:

• Ultrasonic Emission Port
• Antenna
• Channel Switch [channel switch]
• Warning Tone Button [warning tone]
• LCD Screen (displays mode, level, battery)
• Battery Level Indicator [battery]
• Level UP/DOWN Buttons [level up/down]
• Vibration Button [vibration]
• Power ON/OFF Switch [power on/off]
• Shock Button [shock]
• Charging Port

Note: The remote transmitter will enter sleep mode if no action is taken for one minute.

Receiver

The receiver unit features:

• Charging Port
• Speaker
• Contact Points
• Indicator Light
• Power ON/OFF Button [power on/off]

4. Quick Start Guide

1. Charge the Device: Charge the receiver and remote transmitter using the included charging cable for 2-3 hours until the indicator lights up green.

   Note: Use the provided charging cable. Other cables may not be compatible and could cause damage. The collar supports 5V USB power sources exclusively.

2. Power On/Off:
   • Transmitter: Slide the switch to the 'ON' position; the LCD screen will illuminate. To turn off, slide the switch to 'OFF'.
   • Receiver: Press and hold the power button for 2 seconds. A beep and vibration will indicate it's on, and the green LED will blink regularly. To turn off, press and hold the power button for 2 seconds; a long beep will indicate it's off, and the green LED will stop blinking.
3. Fit the Receiver:

   Place the receiver on your dog's neck, close to the ears. Ensure the metal contact points are positioned under the dog's neck, touching its skin. Leave about one finger's width of space between the collar and the dog's neck. For best contact, fur around the contact points may need to be trimmed. Check the fit after a few minutes and again later as the dog gets used to it.

4. Operating Modes:
   • Ultrasonic Mode: Press the [ultrasonic] button. The device will emit an ultrasonic sound. It will automatically shut off after 10 seconds of continuous press. There are 3 ultrasonic levels. Adjust the level by pressing the [ultrasonic] button first, then the [Level UP]/[Level DOWN] buttons. The maximum ultrasonic range is 15 meters.
   • Warning Tone Mode: Press the [warning tone] button. The green LED on the transmitter will blink rapidly. The receiver will emit a warning tone, and its green LED will light up. Adjust the tone level by pressing the [warning tone] button first, then the [Level UP]/[Level DOWN] buttons. There are 8 warning tone levels.
   • Vibration Mode: Press the [vibration] button. The green LED on the transmitter will blink rapidly. The receiver will vibrate, and its green LED will light up. Adjust the vibration level by pressing the [vibration] button first, then the [Level UP]/[Level DOWN] buttons. There are 16 vibration levels.
   • Shock Mode: Press the [shock] button. The red LED on the transmitter will light up. The receiver will send a static shock, and its green LED will light up. Adjust the shock level by pressing the [shock] button first, then the [Level UP]/[Level DOWN] buttons. There are 99 shock levels.

     For the first-time shock function test, place the test bulb on the contact points. The test bulb will light up, indicating the shock function is working. It will shine brighter at higher shock levels.

5. Channel Switching: If you have paired two receivers, use the channel switch on the left side of the remote transmitter to select which receiver you want to control. This product allows training for up to 2 dogs.

5. Pairing the Remote Transmitter with the Receiver

If the receiver does not respond to the remote transmitter signal, follow these steps to pair them:

1. Press and hold the power button on the receiver for 2 seconds to turn it on. Turn on the remote transmitter by sliding the switch to the 'ON' position; the LCD screen will light up.
2. Press the receiver's power button multiple times to enter pairing mode. You will hear a beep, and the indicator light will turn green. You have 10 seconds to complete the pairing.
3. Press the warning tone, vibration, or shock button on the remote transmitter. The receiver will respond accordingly, indicating successful pairing.

The receiver is factory-paired to the remote transmitter on channel 1. If you purchase a new receiver, you can pair it to channel 2 using the same instructions. The system can pair a maximum of 2 receivers on 2 different channels. If you cannot pair the devices, signal interference may be the cause. Try pairing again in a different location or contact our service center.

6. How the System Works

The remote training collar is easy to use and features an advanced LCD display that shows the exact level of stimulation being used. The remote training collar helps control your dog off-leash. Simply press a button, and the transmitter sends a signal to the dog's receiver or emits ultrasonic sounds, effectively capturing its attention. The dog receives safe but noticeable stimulation. It will quickly learn the association between its behavior and your correction, leading to a better-behaved dog. The Remote Training Collar has been tested for safety, comfort, and effectiveness for dogs of small and large breeds. With consistent and proper use, you can teach your dog basic obedience commands and help correct any unwanted behaviors.

7. LCD Display and Indicator Definitions

Remote Transmitter:

• [Warning Tone Icon] Warning Tone Mode
• [Vibration Icon] Vibration Mode
• [Shock Icon] Shock Mode
• [Ultrasonic Icon] Ultrasonic Mode
• [Level Display] Warning Tone / Vibration / Impulse / Ultrasonic Level
• [Battery Icon] Remote Transmitter Battery

Remote Transmitter Indicator Lights:

• Charging: Green indicator light blinks regularly.
• Fully Charged: Green indicator light is solid.
• Pressing [Warning Tone] or [Vibration]: Green indicator light turns on.
• Pressing [Shock] or [Ultrasonic]: Red indicator light turns on.

Receiver Indicator Lights:

• Slow blinking: Receiver is ON.
• Fast blinking: Receiver is charging.
• Faster blinking: Receiver battery is low.

8. Training Tips

Finding the Best Stimulation for Your Dog

Important: Always start at the lowest level and gradually increase. The remote training collar offers 3 ultrasonic levels, 8 types of warning tones, 16 vibration levels, and 99 impulse levels. For ultrasonic and warning tones, the difference is only in frequency. For vibration and impulse, level 1 is the lowest; level 16 is the highest for vibration, and level 99 for impulse. This allows you to select the stimulation level that is best for your dog. Once the receiver is placed on the dog, it's time to find the stimulation level that works best for it. This is called the recognition level.

When using the four training modes, follow the principle of starting from mild to strong. Begin with the warning tone and vibration modes, and use the ultrasonic mode only if necessary. High-frequency ultrasonic waves strongly stimulate the dog's hearing without causing damage, making them more effective than the warning tone or vibration modes. Electric impulse mode should only be used as a last resort. Additionally, combining these methods with positive reinforcement, such as rewards and praise, can increase training effectiveness.

A slight change in the dog's behavior, such as looking around curiously, scratching at the collar, or flicking its ears, indicates your dog's recognition level.

To check your dog's recognition level, follow these steps:

1. Starting at level 1, press and hold the warning tone/vibration/impulse button for 1-2 seconds.

Note: If the warning tone/vibration/impulse button is held for 10 seconds, the remote transmitter will turn off, and you will need to release and press the button again to deliver further stimulation.

• If the dog does not react, repeat the stimulation level several times before moving to the next level.
• Your dog should not whimper or panic during stimulation. If this occurs, the stimulation level is too high, and you should return to the previous level and repeat the procedure.
• Progress through the stimulation levels until the dog begins to react to the stimulation.
• If your dog still does not react at the highest vibration or static impulse level, check the receiver fit. If your dog has long or thick fur, contact our Customer Service Center to obtain a longer set of contact points. Then, return to step 1 and repeat the procedure.
• If this does not yield results, the dog's fur around the contact points may need to be trimmed.
• If, after all steps, the dog still shows no sign of feeling the stimulation, contact our customer service department.

How to Get Your Dog's Attention with Ultrasonic Sounds

Press the ultrasonic mode to emit ultrasonic sounds that effectively capture your dog's attention. This will help it understand and respond to training commands. When the dog behaves undesirably, such as barking, jumping, stealing food, or inappropriate chewing, quickly press the ultrasonic button. Simultaneously, give a verbal command such as "NO," "QUIET," "SIT," "STAY," or "STOP" to help the dog cease the unwanted behavior.

Note: This function is specifically designed for dogs. It may not be audible to all humans. Avoid placing it near human ears.

How to Maximize Ultrasonic Transmission Range

1. Choose a clear, open area without shade. Avoid dense forests, buildings, strong winds, and moisture. Limit use in high temperatures and high humidity to ensure better transmission.
2. Aim the ultrasonic emission port directly at the dog, keeping it in a straight line.
3. Regularly clean the ultrasonic emission port on the dog training collar to prevent dust and moisture buildup and ensure optimal ultrasonic emission.

How to Maximize the Wireless Remote Range

Maximum range is affected by factors such as terrain, weather, vegetation, and transmission from other radio devices.

For optimal range, hold the transmitter horizontally, away from your body. For maximum signal strength, keep the device adequately charged.

9. Frequently Asked Questions (FAQ)

Q: While the Stimulation is unpleasant, it is harmless to your dog. Electronic training devices require interaction and training from the owner to achieve desired results.

P: Is the stimulation safe for my dog?

A: Yes, the stimulation is safe for your dog. It is designed to be noticeable but not harmful.

P: How old must my dog be to use the training collar?

A: Your dog should be able to recognize basic obedience commands such as "Sit" and "Stay." Dogs should be at least 6 months old to use the Trainer device.

P: Is the receiver waterproof?

A: Yes. The receiver meets IP67 water resistance standards, but ensure the charging port is dry during charging. Note: The remote transmitter is not waterproof.

P: Does the ultrasonic mode work effectively on all dogs?

A: The product emits ultrasonic sounds, which may be ineffective for older dogs or dogs with hearing problems. Different dog breeds react differently to ultrasonic frequencies. Please use it as a training aid along with verbal commands and exercise patience during training.

P: Will the remote-controlled training collar provide me with maximum range?

A: The range of the dog training collar will vary depending on terrain, weather, vegetation, and transmission from other radio devices. For tips on maximizing range, refer to the section "How to Maximize the Wireless Remote Range" on page 19.

Q: How long can I continuously stimulate my dog?

A: The maximum time you can press the warning tone/vibration/impulse/ultrasonic button and continuously stimulate your dog is 10 seconds. After this time, the remote transmitter will turn off, and you must release and press the stimulation buttons again.

P: How can I check if I can use this product on my dog?

A: The product is intended for healthy dogs over 6 months of age. Most importantly, do not use it on dogs that are sick or aggressive. If you are unsure whether the product is suitable for your pet, consult a veterinarian or a certified trainer.

P: Can I charge this product using any type of charger?

A: No, it is recommended to charge this product using a charger with a 5V output voltage, as a charger with an output voltage above 5V may cause damage to the product. The product will automatically stop charging if the input voltage becomes too high and will emit a warning signal.

10. Troubleshooting

1. My dog does not respond when I press a button.

• Check if the receiver is turned on.
• If the training collar's range has decreased since the first use, it may indicate that the transmitter or receiver battery is low.
• Range can be affected by many factors. A list of these factors can be found in the section "How to Maximize the Wireless Remote Range" on page 19.
• Test the receiver using the test bulb. NOTE: If the test bulb does not blink, charge the receiver and repeat the test. If the test bulb still does not blink, contact our customer service department.
• Increase the stimulation level. More information can be found in the section "Finding the Best Stimulation for Your Dog" on page 19.
• Ensure the receiver's metal contact points fit snugly against the dog's skin. More information can be found in the section "Receiver Mounting" on page 15.

2. The receiver does not turn on.

• Ensure the receiver is charged. For the first charge, ensure it is charged for 4 hours. Subsequent charges only take 2-3 hours.

3. The receiver does not respond to the remote transmitter signal.

• Check if the receiver is turned on.
• If the indicator blinks fast, it means the receiver is fully charged.
• If the first two solutions do not resolve the problem, refer to the "Pairing" section on page 15 to re-pair the receiver with the remote transmitter.

11. FCC Statement (USA)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If interference to radio or television reception occurs, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• For assistance, contact the customer service department, dealer, or an experienced radio/TV technician.

12. CE Approval and Service

The device has been approved for use in EU countries and therefore carries the CE marking. All necessary documentation is available on the website: www.obroza-elektryczna.pl. Changes in technical parameters, functions, and printing errors are reserved.

Service and Distribution

Reedog s.r.o

Sedmidomky 459/8

101 00 Prague 10

Czech Republic

Tel: +48 443 444 443

E-mail: info@obroza-elektryczna.pl