Reedog V2 Anti-Bark Collar
Please read these instructions before use.
Important Safety Information
This product is designed for humane correction using improved vibration and sound technology to help stop barking in small and medium-sized dogs, without electrostatic pulse. It is not suitable for aggressive dogs and should be used under supervision. Do not leave the product on the dog for more than 12 hours a day. Never attach a leash to the collar. Check daily for signs of irritation or soreness at the contact point. If irritation or soreness occurs, discontinue use immediately until the skin heals. Weekly, wash the dog's neck and the contact point area with a damp cloth. The product captures high-frequency barking, and other dogs' barks may have a low chance of activating it. Reduce the sensitivity level when another dog is nearby.
Product Information
Receptor V2: Collar, USB Cable, Manual
Components: Charging port, Contact points, Collar, USB Cable, Microphone sensor, Vibration mode button, Sensitivity level display, On/Off button, Vibration mode button, Setting button.
Product Test
1. Charge the anti-bark collar before use.
You can charge the product via computer, power bank, or adapter with a 5V output.
Power Indicator Description:
- Flashing green: device is charging
- Solid green: device is fully charged
- Solid red: device is charging with the wrong charger
1B. Turn on the anti-bark collar.
Press and hold the button for 2 seconds to turn on. When the device is on, the indicator light will be red or green.
1C. Set the anti-bark collar to test mode.
Press the power button to enter test mode, ensure the display shows '0' before testing. Then, blow or bark like a dog towards the microphone sensor on the back of the product.
In test mode: When the device is in test mode, the collar will vibrate, beep, and then vibrate more strongly after you blow or shout towards the microphone sensor.
If the product responds as described, you have set the collar correctly!
2. Put the collar on the pet
2A. Attach the collar to the collar receiver.
Follow instructions A-B-C-D.
Note: Seal the edge of the cut collar by holding it over a flame for a few seconds.
2B. Put the collar on the dog.
Ensure the collar fits snugly but is loose enough to allow one finger to fit between the collar and the animal's neck.
Great! You have successfully fitted the anti-bark collar and the dog is ready to be trained.
3. Mode Setting
Follow these instructions to switch modes.
Turn on the device by pressing and holding the button for 1 second. When the device is on, the mode indicator will be green or red. Press the 'M' button to switch modes.
- Green mode indicator: vibration mode
- Red mode indicator: strong vibration mode
Indicator and Display
| Indicator | Mode Indicator | Power Indicator | Sensitivity Level |
|---|---|---|---|
| Vibration Mode | SOLID (Green) | SOLID | Level 1-5 |
| Strong Vibration Mode | SOLID (Red) | SOLID | Level 1-5 |
| Charging/Low Battery | SOLID | BLINKS | N/A |
| Test Mode | SOLID | SOLID | 0 |
Charging: When the device is on and charged with the correct charger, the power indicator lights up. When the device is off and charged with the correct charger, the power indicator remains off and lights up when the button is pressed. Incorrect chargers are those with an input voltage higher than 5V. The product will automatically stop charging if the input voltage is too high and the power indicator turns red.
Sensitivity Levels: Level 5 is the most sensitive, Level 1 is the least sensitive. Sensitivity levels are changed by pressing a button.
Test Mode: Press the button to enter test mode. The display shows '0' when test mode is set. When the test is complete, the display automatically shows numbers, or if the test is not performed within 10 seconds.
5. How it Works
Vibration Mode:
- Dual motor technology
- If your dog continues to bark, remain in Step 6. Return to Step 1 if the device is not activated for one minute.
Strong Vibration Mode:
- Dual motor technology
- The device will proceed to the next step if your dog barks within a 1-minute interval. It will automatically return to Step 1 if the product is not activated within 1 minute.
6. Frequently Asked Questions
Q: Why doesn't the product work when the dog barks?
A: First, ensure the product is fitted snugly but loosely enough for one finger to fit between the collar and the pet's neck. Some dogs bark softly, in which case you need to increase the sensitivity level. Thick fur in the neck area may also reduce detection; trim the fur close to where the product is placed.
Q: Why does the product occasionally activate in noisy environments even when the dog is not barking?
A: Although the bark detection has been optimized, some environmental sounds may have a similar frequency to barking, which may cause occasional false activation. Please reduce the sensitivity level.
Q: Can I use the product when other dogs are playing nearby?
A: Dogs bark and get excited when playing. For your pet's comfort and safety, using this product in such an environment is not recommended.
Q: How do I know if I can use this product for my pet?
A: The product is intended for healthy dogs over 6 months old. It is not suitable for unhealthy or aggressive dogs. If you are unsure whether this product is appropriate for your pet, consult a certified veterinarian or trainer.
Q: Will this product stop my dog from howling? Can this product stop my dog from howling?
A: No, this anti-bark collar is designed only to detect barking. It cannot detect or stop howling.
Q: What can I do with this product? Can I charge this product with any type of charger?
A: No, it is recommended to charge this product with a charger that has a 5V output voltage. A charger with a 9V or 12V output voltage may damage the product. The product will automatically stop charging if the input voltage is too high, and the power indicator will turn red.
Q: Is the anti-bark collar safe and humane?
A: The anti-bark collar is designed to get the dog's attention, not to punish it. This product does not have a shock unit and will only provide correction through tone and vibration. However, the initial strong vibration correction may startle your dog.
If the FAQ cannot resolve your issue or you need further assistance, please contact customer service.
Service and Distribution
Reedog, s. r. o.
Sedmidomky 459/8
101 00 Prague 10
Czech Republic
Tel: +420 216 216 106
E-mail: info@reedog.ro
Website: www.reedog.ro
Website: www.zgarzi-electro.ro
