Reedog PATPET 690 User Manual

Product Description

Product Setup

Before using the dog training collar, configure the product by following these steps:

1. Charge the remote control and the receiver collar.
2. Prepare and turn on the remote control.
3. Prepare and turn on the receiver collar.
4. Test the button functions before putting it on your dog.
5. Pair the remote control and the receiver collar.

Charging

Charge the remote control and receiver collar:

1. Connect and fully charge the remote control and receiver collar. Charge for 4 hours for the initial charge. Subsequent charges take 2-3 hours.
2. When fully charged, the red LED on the receiver collar will turn green.
3. Replace the rubber cover when the receiver collar is fully charged.

Attention: Overcharging will shorten the battery life. Charge only when the batteries are nearly depleted. When not in use, turn off the collar to prolong battery life.

Remote Control Preparation

Turning the remote on/off:

1. Switch the channel converter from 1 to 2. Turn on the remote control. (If you have a single receiver, switch to 1).
2. The LCD screen will light up and display information about the current channel, battery status, and selected levels. If not, please charge the remote control.
3. Press the channel converter switch to turn off the remote control.

Receiver Preparation

Use a test light to install the contact points.

You can also use a spring, which will make the electrode contact more efficient and comfortable.

Turning the receiver collar on:

• Press the on/off button; the green LED indicator will light up.
• In normal mode, the green LED will flash every 4 seconds, indicating that the collar is ready to receive a signal from the remote control.

Turning the receiver collar off:

• Press and hold the on/off button until the red LED turns off.
• Release the on/off button.

Test

It is recommended to test the correction levels yourself, always starting with the lowest level and increasing the level to your comfort level.

1. Place a finger on both contact points of the training collar.
2. Hold the remote control approximately 60 cm from the training collar. Press and hold the vibration button for 1 to 2 seconds. You should feel continuous vibrations.
3. Press to decrease levels.
4. Starting from level 1, press the shock button. Increase the level until you feel discomfort.

Sound Feature:

Sends an unadjustable sound to the receiver collar.

Vibration Feature:

Sends an unadjustable vibration to the receiver collar.

Pulse Function:

Sends 1-16 adjustable levels of static pulse to the receiver collar.

Test Discharge

1. Turn on the receiver.
2. Hold the test light against the electrodes.
3. Press the pulse function on the remote control; if everything is working correctly, the test light will turn on.

Connecting the Transmitter to the Receiver

1. Use the switch on the remote control to select channel 1 for the dog.
2. When the remote control is on and the receiver collar is off, press and hold the ON/OFF button on the receiver collar for 4-5 seconds.
3. The red and green LEDs will flash for approximately 10 seconds, indicating it is ready for pairing.
4. Press and hold the tone and vibration buttons simultaneously on the remote control for 2-3 seconds; the green light on the receiver collar will flash 5 times, indicating successful pairing.

Pairing a second collar with the remote control:

Use the button on the remote control to select channels 1 and 2. Then, follow pairing steps 2-4 above.

Correct Application of the Collar

Important: Correct fitting and placement of the receiver collar are essential for its efficient operation. The contact pins must be in direct contact with the dog's skin, at the base of the neck. To ensure safe and correct collar function, it must be applied correctly.

• Each electronic collar must fit snugly against the skin. The electrodes must fit perfectly on the skin under the fur, but should not be tight.
• If the collar is too loose, the stimulation will not work correctly, as the electrodes will not make proper contact with the animal's skin. If the dog does not respond to stimulation, always check if the electrodes are securely fastened to the skin.
• During training or running, a collar that is too loose can cause skin irritation on the animal's neck. A properly fitting collar will help prevent irritation.
• Correct collar adjustment is important. It should be adjusted so that it does not strangle the dog and allows it to breathe normally. The collar should never impede the animal's breathing.
• The receiver collar should be placed correctly in the center of the animal's neck.

To ensure maximum effect and safety for your dog, check the collar placement, its tightness, and the correct placement of the electrodes. Also, check the skin where the electrodes touch for any rash or irritation. In such cases, wear the collar for shorter periods or consult a veterinarian. Do not attach a leash to the collar. The collar should not be worn continuously for more than 12 hours a day (this is a recommendation for all collars, even non-electric ones). If irritation occurs, remove the collar until all signs of irritation have disappeared.

Maintenance

• Periodically check that the contact pins are not too tight against the dog's skin.
• Clean the contact points once a week with an alcohol-based product.
• Periodically check the dog's neck for signs of skin irritation.
• Wash the dog's neck regularly.
• If the strap is too long, do not hesitate to shorten it slightly.

Service and Distribution

The device has been approved for use in EU countries and therefore bears the CE mark. All necessary documentation is available on the website: www.reedog.ro. Changes to technical parameters, features, and typographical errors may be subject to modification.

Reedog, s. r. o.
Sedmidomky 459/8
101 00 Prague 10
Czech Republic
Tel: +420 216 216 106
E-mail: info@reedog.ro