Reedog Dog Training Collar

User Manual

Product Image

The product is a dog training collar system consisting of a remote transmitter and a collar receiver. The remote has a digital display showing settings and buttons for mode selection, level adjustment, and channel selection. The receiver is a small unit that attaches to the collar.

Features

Rechargeable: Both the remote and receiver are rechargeable.
Water-Resistant Receiver: The receiver is waterproof, allowing pets to swim or walk in the rain.
Adjustable Levels: Vibration and shock modes can be adjusted from levels 1 to 99.
Four Training Modes: Shock, Vibration, Light, and Sound.
Three Channels: Allows control of up to 3 receivers with a single remote.
Auto Power Saving: The remote and receiver enter standby mode after 5 minutes of inactivity.

Tips for Use

Charge the device before first use.
Address one behavior or command at a time to avoid confusing the pet.
If using the shock mode, try the vibration mode first.
Observe the dog's reaction to ensure the training intensity is not too high.
Check the dog's skin to prevent injury from shocks.

Key Definitions

Antenna: Transmits a strong signal.
LED Light: Press to turn on/off.
LCD Screen: Displays modes, levels, and channels.
Shock Button: Selects shock mode. Press the Shock button again to deliver a shock. Use '+' or '-' buttons to adjust levels (0-99).
Vibration Button: Selects vibration mode. Use '+' or '-' buttons to adjust levels (0-99). Press the Shock button to activate vibration.
Sound Button: Selects sound mode. No level adjustment needed; press to make the receiver emit a sound.
'-' Button: Decreases levels.
'+' Button: Increases levels.
Channel Button: Selects the training channel (CH1/CH2/CH3).
Light Button: Turns on the remote's LED. Press and hold for 2 seconds to turn on the receiver's white LED; press and hold again for 2 seconds to turn it off.
Power Button: Press to turn the receiver on/off.
Contact Points: For installing the rubber cap to reach the pet's skin for static contact.
Indicator Light: Flashes when shock/vibration/sound buttons are pressed; stays on during charging.

Charging the Remote and Receiver

Charging the Remote: Connect the cable to the charging port, connect the USB adapter, and plug it into the outlet. The battery icon will flash during charging and stop when fully charged.
Charging the Receiver: Open the rubber cover of the charging port. Connect the cable, USB adapter, and plug into the outlet. The green LED indicator will flash during charging and remain solid when fully charged.

Note: Charge for at least 5 hours for the first use. The receiver enters standby mode when charging and cannot receive signals. A low battery is indicated by an icon on the remote or a flashing light on the receiver. Fully charge before long periods of inactivity, at least once a month.

Auto Power Saving Function

If no operation is performed on the remote for 10 seconds, the screen backlight turns off. After 30 seconds of inactivity, the remote enters standby mode with the screen off. Press any button to activate it.

If the receiver does not receive a signal for 5 minutes, it enters standby mode. Press the shock, vibration, or sound button to activate it.

Pairing the Remote and Receiver

Press the shock or vibration button to turn on the remote.
Select a channel (CH1, CH2, or CH3) using the CH button.
Adjust the level using the '+' or '-' buttons (ensure it's above 01).
Press and hold the receiver's power button for 3 seconds until a "Bee" sound is heard and the indicator light flashes. Within 10 seconds, press the vibration or shock button on the remote. You should hear another "Bee" sound, indicating successful pairing.
For 2 or 3 receivers, select a different channel for each and repeat the pairing process.

Note: Remember the selected channel for pairing. If using a different channel without association, you cannot control the receiver.

Testing the Training Collar Set (After Successful Pairing)

Test Shock Function: Attach the test light to the receiver's contact points. Press the shock button (ensure the level is above 01). The test light should illuminate.
Test Vibration Function: Press the vibration button (ensure the level is above 01). The receiver will vibrate.
Test Sound Function: Press the sound button. The receiver will emit a beep.

How to Wear the Receiver on Your Pet

Place the receiver on the dog's neck.
Ensure the contact points touch the dog's skin. Select the appropriate rubber cap for the contact points.
Adjust the collar strap so the dog feels comfortable.

F.A.Q

Q: Collar length?
A: The collar length is 27.5 inches (70 cm).
Q: What is the suitable weight for dogs using this collar?
A: We suggest dogs over 20 lbs.
Q: Is the receiver waterproof?
A: Yes, it is fully waterproof, and your dog can swim with it.
Q: How long should my dog be trained each time?
A: 10 - 15 minutes.
Q: What should I do if the training collar set is not working?
A: 1. Check the battery power of the remote and receiver; charge if discharged.
2. Check the level; if using vibration or shock mode, set it to 001 or higher.
3. Check the receiver; if it's not turning on, press the power button.
4. Check the channel; if using a different channel, use the up/down buttons to adjust.
5. Repair the remote and receiver.
6. Check the metal screw cap; if it's too short, replace it with a longer one.

Specifications

Frequency: 915MHz
Transmitter: 3.7V 300mA LIP
Receiver: 3.7V 240mA LIP
Made in China

Approvals and Contact

The device has been approved for use in EU countries and carries the CE mark.

All necessary documentation is available on the website: www.reedog.ro.

Technical parameters, features, and typographical errors are subject to change.

Service and Distribution:
Reedog, s. r. o.
Sedmidomky 459/8
101 00 Prague 10
Czech Republic
Tel: +420 216 216 106
E-mail: info@reedog.ro

	Reedog P19 Dog Training Collar: User Manual and Guide Comprehensive guide to using the Reedog P19 Dog Training Collar, covering setup, training modes, fitting, safety precautions, and troubleshooting. Learn how to effectively train your dog with this remote-controlled system.
	Reedog PATPET 502 User Manual User manual for the Reedog PATPET 502 dog training collar, detailing its features, operation, charging, and pairing procedures.
	REEDOG RS11 Ultrasonic Dog Training Collar User Manual Comprehensive user manual for the REEDOG RS11 2-in-1 Ultrasonic Dog Training Collar, covering safety, package contents, product description, quick start guide, training functions, fitting, pairing, and indicators.
	Reedog S1 Smart Dog Bark Control Collar User Manual Comprehensive user manual for the Reedog S1 Smart Dog Bark Control Collar. Learn about safety guidelines, product features, testing procedures, proper fitting, operating modes, indicator lights, how the device works, and frequently asked questions for humane and effective dog barking management.
	Reedog TC-021 Training Collar Quick User Card Quick user guide for the Reedog TC-021 training collar, covering training operations and pairing procedures.
	Reedog RS11 Ultrasonic 2-in-1 Dog Training Collar User Manual Comprehensive user manual for the Reedog RS11 Ultrasonic 2-in-1 Dog Training Collar, covering setup, operation, training modes, safety, and troubleshooting.
	Reedog PATPET 690 Dog Training Collar User Manual User manual for the Reedog PATPET 690 dog training collar, covering product description, setup, charging, testing, and proper application. Learn how to use the remote and receiver, charge the device, test its functions, and ensure correct fitting for your dog's safety and comfort.
	Reedog V2 Anti-Bark Collar User Manual Instructions for using the Reedog V2 anti-bark collar, including safety information, product features, setup, operation, and troubleshooting.