GDW Tow Bar for BMW 7 Series (E65, 2002-...)
GDW Reference: 1382
Vehicle: BMW 7 Series, E65 (2002 - ....)
EEC Approval Number: e6*94/20*0375*00
Technical Specifications
The D-value calculation is as follows: D = (max kg × max kg) / (max kg + max kg) × 0.00981 ≤ 12.00 kN
Maximum vertical load (s/): 100 kg
Maximum towing capacity: 2300 kg
Diagram Description: A diagram illustrates the D-value calculation formula with placeholders for maximum weights in kilograms. It also shows the maximum vertical load (s/) as 100 kg and the maximum towing capacity as 2300 kg.
Tow Bar Assembly Diagram
Diagram Description: This diagram shows the tow bar assembly for the BMW 7 Series E65. Key connection points are labeled A, B, and C. The specific model shown is the "T36 Escamotable" type.
Bumper Cut-out Information
Diagram Description: A diagram indicates the area of the bumper that needs to be cut out for installation. The hatched area is to be removed. Key reference points are labeled 'B' (bumper), 'O' (lower rim of bumper), and 'M' (middle of bumper). Dimensions provided are approximately 100mm (height), 171mm (width), 75mm (depth), and 30mm (offset).
Installation Instructions
- Disassemble the bumper. Permanently remove the buffer beam. Note: The plastic part of the bumper will be reattached to the tow bar.
- Place the tow bar onto the vehicle's mounting points (A and B) where the buffer beam was originally attached. Insert washers and nuts, and tighten securely.
- Slide the snap nuts onto points (C). Place the plastic part of the bumper onto the provided tubes of the tow bar. Reassemble the bumper and tighten all fasteners firmly.
- Install the T45 ball coupling between the fixing plates, or insert the T36 detachable ball coupling into its socket.
Component Composition
Tow Bar Reference 1382
- 1 x Ball coupling T45L035
- 2 x Bolts M12x65 - DIN931
- 2 x Bolts M12x70 - DIN931
- 4 x Lock nuts M12 - DIN985
- 2 x Mounting plates T45 (800008)
- 1 x Safety shackle (-s) (800000)
- 2 x Tubes (800011)
- 6 x Nuts M10 - DIN934
- 6 x Lock washers M10 - DIN128A
- 4 x Rivets
- 2 x Washers 24x13x2.5mm
All bolts and nuts are quality 8.8.
Torque Specifications
Quality 8.8 Bolts
| Bolt Size | Torque (Nm) | Torque (kgm) |
|---|---|---|
| M6 | 10.8 | 1.1 |
| M8 | 25.5 | 2.60 |
| M10 | 52.0 | 5.30 |
| M12 | 88.3 | 9.0 |
| M14 | 137 | 14.0 |
| M16 | 211.0 | 21.5 |
Quality 10.9 Bolts
| Bolt Size | Torque (Nm) | Torque (kgm) |
|---|---|---|
| M6 | 13.7 | 1.4 |
| M8 | 35.3 | 3.6 |
| M10 | 70.6 | 7.20 |
| M12 | 122.6 | 12.5 |
| M14 | 194 | 19.8 |
| M16 | 299.2 | 30.5 |
Clearance and Vehicle Weight
Diagram Description: Diagrams illustrate clearance requirements according to guideline 94/20/EG, Appendix VII, diagram 30. These include maximum angles (30°, 45°) and minimum/maximum distances (e.g., min 140, max 100).
Consult your vehicle's dealer or owner's manual for the maximum permissible towing mass.
Ensure any bitumen coating or anti-vibration material is removed from the mounting points.
When drilling, exercise caution to avoid damaging brake lines, electrical wiring, or fuel lines.
Note on Vehicle Weight: Information is provided regarding the permissible total weight of the vehicle.
GDW nv Contact Information
GDW nv
Hoogmolenwegel 23
B-8790 Waregem
TEL: +32 (0)56 60 42 12 (5)
FAX: +32 (0)56 60 01 93
Email: gdw@gdwtowbars.com
Website: www.gdwtowbars.com
