ASSEMBLY INSTRUCTIONS
Counter & Bar Height Stool
Parts List
Please familiarize yourself with the parts and steps before assembly. Note: Do NOT use power tools for assembly.
- Part 1: Seat [x1]
- Part 2: Circular seat base [x1]
- Part 3: Backrest [x1]
- Part 4: Front leg [x1]
- Part 5: Rear leg [x1]
- Part 6: Footrest [x1]
- Part 7: Backrest support [x1]
- Part 8: Swivel plate [x2]
- Bolt A (longest, M6x30mm) [x1]
- Bolt B (M6x12mm) [x4]
- Bolt C (M6x18mm) [x12]
- Bolt D (M6x25mm) [x4]
- Washer E (flat, M6x12mm) [x12]
- Tool F (Allen wrench) [x1]
- Tool G (Allen wrench) [x1]
Step 1: Attach Legs
Unpack and place seat (1), legs (4 & 5), footrest (6), and swivel plate (8) on a clean surface. Attach the leg part (4) to leg part (5) using the longest bolt (A) and Allen wrench (G). Note: Do not fully tighten yet. [Diagram shows parts laid out, and close-up of bolt A connecting legs 4 and 5, with wrench G. Indicator shows 80% complete.]
Step 2: Attach Footrest
Attach footrest (6) to stool legs. Loosely attach the bolts (D) one by one, keeping them loose. After loosely attaching the first bolt, move on to the diagonal bolt. After all 4 bolts are attached, use Allen wrench (F) to tighten. Note: Do NOT use power tools for assembly. [Diagram shows footrest 6 connecting to legs 4 and 5 with bolts D and wrench F. Indicator shows 80% complete.]
Step 3: Tighten Legs and Attach Swivel Plate
Fully tighten the longest bolt (A) from step 1 with Allen wrench (G). Then attach swivel plate (8) to the assembled legs using bolts (C), flat washers (E), and Allen wrench (F). Fully tighten all the bolts. [Diagram shows tightening bolt A, then attaching swivel plate 8 to the leg assembly with bolts C, washers E, and wrench F. Indicator shows 100% complete.]
Step 4: Attach Seat Base
Attach the circular seat part (2) to seat part (1) using bolts (C), flat washers (E), and Allen wrench (F). Fully tighten all the bolts. [Diagram shows seat part 1 and seat base 2 being joined with bolts C, washers E, and wrench F. Indicator shows 100% complete.]
Step 5: Attach Legs to Seat
Turn the assembled legs (from step 3) upside down and attach them to the seat (1) (from step 4) using bolts (C), flat washers (E), and Allen wrench (F). Note: Tighten all bolts. [Diagram shows the leg assembly being attached to the bottom of the seat assembly with bolts C, washers E, and wrench F. Indicator shows 100% complete.]
Step 6: Assemble Backrest
Attach parts (7) (backrest support) to backrest part (3) using bolts (B) and Allen wrench (G). Note: Do not fully tighten yet. [Diagram shows backrest 3 being attached to support 7 with bolts B and wrench G. Indicator shows 80% complete.]
Step 7: Attach Backrest to Seat
Attach the assembled backrest (from step 6) to seat part (1) using bolts (B) and Allen wrench (G). Fully tighten all the bolts. [Diagram shows the backrest assembly being attached to the seat assembly with bolts B and wrench G. Indicator shows 100% complete.]
Step 8: Final Placement
Turn the assembled chair upright and place it on a flat surface. Note: Each leg has an adjustable foot leveler to help level your chair. [Diagram shows the completed chair being turned upright, with a close-up of a leg showing an adjustable foot leveler.]
Step 9: Assembly Complete
Assembly complete. Enjoy.
