SelectBlinds Roller Shade Installation Guide

General Information

Difficulty Level: Varies by lift system (Level 1 - A piece of cake! to Level 2 - You got this!).

Customer Support: Call 888-257-1840 or email customercare@selectblinds.com for assistance.

Hardware and Parts Included

• Cassette Brackets
• Cordless Handle
• Screws
• Tension Device (Continuous Cord Loop)
• Battery Charger (Motorized)
• Remote & Holder (Motorized)

Note: The quantity of brackets depends on the width of your shade.

Tools Required

• Pencil
• Tape Measure
• Power Drill
• Step Ladder
• Level
• 5/64" Drill Bit
• Phillips Bit

Mounting the Brackets

Inside Mount

1. Measure and mark 2"-4" from each side of the window top corners. Add additional marks for extra brackets, evenly spaced.
2. Measure back at least 2" from the marks for bracket depth. For flush mounting, measure 3 1/2" (exposed roll) or 3 7/8" (cassette). Mark the depth.
3. Align brackets with marks, mark screw holes.
4. Pre-drill holes with a 5/64" drill bit. Erase pencil marks.
5. Secure brackets with screws.

Outside Mount

1. Measure and mark 2"-4" inward from each side of the window top corners.
2. Measure upward from these marks for bracket height (minimum 1 1/4" or 1 1/2" for clearance). Mark the height.
3. Position bracket, mark screw holes.
4. Pre-drill holes with a 5/64" drill bit. Erase pencil marks.
5. Secure brackets with screws.

Attaching the Shade

General Note

Ensure brackets are straight and aligned. Elongated screw holes allow for adjustments.

Inside Mount Adjustment

Use a tape measure to ensure brackets are at the same depth. Loosen screws slightly to adjust and re-secure.

Outside Mount Adjustment

Use a tape measure and level to ensure brackets are at the same height and aligned. Loosen screws slightly to adjust and re-secure.

Exposed Roll Shade

1. Insert the pin end into the cross hole of the bracket.
2. Insert the motor head/clutch end hooks into the bracket slots. Pull down gently until locked.

Cassette Headrail Shade

1. Set the front edge of the headrail onto the front hook of each bracket. Slide for centering.
2. Push the headrail upward until the back lip of each bracket snaps onto the back edge of the cassette.

Installing No-Drill Blinds Headrail

Preparing the No-Drill Blinds Headrail

1. Pull the lever or push down to retract the tension block.
2. Install metal strips or adhesive tape on opposite sides of the window opening.

Installing the No-Drill Blinds Headrail

1. Adjust the block at the end of the headrail using a flat-head screwdriver to fine-tune fittings. Twist red plugs to slide the block, then twist back to fix.
2. Hold the headrail flush against the top of the window opening and push the lever upwards until it snaps into place.
3. Install the blind onto the brackets.

Uninstalling the No-Drill Blinds Headrail

Use a flat-head screwdriver to unlatch the lever. Hold the headrail while unlatching to prevent damage.

Additional Instructions

Installing Chain Tension Device

Note: Used for smooth operation and child safety. Slide the tension device to the bottom of the bead chain loop before proceeding.

1. Insert a tool through the screw at the bottom of the tension device.
2. Press release buttons and move the screw hole down to release the safety mechanism.
3. Slide the tension device to the desired location at the bottom of the bead chain loop.
4. Mark the window casement at the tension device's notch.
5. Align the screw hole with the notch for a taut but slightly loose chain. Mounting options: Inside Mount (with/without bracket) or Outside Mount.

Programming and Using Your Remote

Important Note

Wake up motorized shades by pressing and holding the setting button for 6 seconds until motors sound and LEDs flash red four times.

Remote Control Technical Data

• Channels: 5+all (RW5-G2), 14+all (RW14-G2)
• Max. blinds: 16 per channel
• Supply voltage: 3V, CR2350 Coin Cell
• Protect Rate: Ip20
• Operation Temp: -20 ... 55°C
• Frequency: ASK 433.92 MHZ
• Indoor range: 35m
• Dimensions: 46 x 122 x 12.4 mm
• Weight: 56 grams

Pairing a Single Shade to a Channel

1. Select the desired shade channel.
2. Remove the battery cover to access the 'C' button.
3. Hold the setting button until the shade jogs (green LED blinks).
4. Hold the setting button again until the shade beeps (red LED blinks).
5. Press the 'C' button while the motor beeps (max 15 secs). The shade jogs, and the green LED flashes to confirm pairing.

Deleting a Shade from Remote

1. Select the desired shade channel.
2. Remove the battery cover to access the 'C' button.
3. Press the 'C' button three times within 2 seconds. The shade jogs, and the green LED flashes to confirm deletion.

Setting the Favourite Position

1. Send the shade to the desired favourite position.
2. Remove the battery cover to access the 'L' button.
3. Hold 'L', then quickly hold 'Heart' until the shade beeps and the green LED blinks to set the favorite position.

Deleting the Favourite Position

1. Press 'Heart' to send the shade to its favourite position.
2. Remove the battery cover to access the 'L' button.
3. Hold 'L', then quickly hold 'Heart' until the shade beeps and the green LED blinks to delete the favorite position.

Changing the Motor Speed

Shades offer three speed levels: Standard, Comfort, and Slow. Changing the speed cycles to the next available level.

1. Ensure the desired shade channel is active.
2. Hold 'Heart', then quickly hold the 'Up' button until the shade beeps and the green LED blinks to change the speed.

Install/Replace the Remote Battery

1. Use a Philips screwdriver to loosen the captive screw on the cover.
2. Slide the battery cover off.
3. Remove the old battery, align the new battery (+ symbol upward), and place it in the socket.
4. Slide the cover back on and tighten the screw.

Mount the Remote Holder

This is optional. Determine placement, insert screws to secure the holder, then attach the screw cap cover.

Troubleshooting

Common Issues

• Backlit buttons not illuminating: Check battery replacement or proper insertion.
• No response when adding blind: Check blind power, charge, and correct group channel.
• Shades not responding to remote: Check remote battery, if blinds are added, blind battery level, or replace remote battery.

Frequently Asked Questions

• Adding blinds without the app: Pair directly by choosing a group number, pressing the blind's manual push button until it jogs twice, then pressing the remote's 'C' button within 15 seconds.
• Copying remote information: Not possible.
• Remote control necessity: Recommended for maximum flexibility, one per room.
• Assigning multiple remotes: Up to 10 remotes can be assigned per shade by repeating the pairing process.
• Number of blinds per remote: 5-channel remote: 5 groups, 16 blinds/group. 14-channel remote: 14 groups, 16 blinds/group.
• Battery type: 3V CR2450 coin/button cell battery.
• Out-of-the-box functionality: Remote requires assignment to shade or via SmartView app.

Safety Instructions

Important Safety Instructions

• Do not ingest batteries.
• Keep batteries away from children.
• Seek immediate medical attention if a battery is swallowed.
• Use correct battery type.
• Do not dispose of batteries in fire or crush them.
• Avoid extreme temperatures and low air pressure.
• Keep the device dry and do not paint it.
• Do not drop, knock, or shake the device.
• Ensure the shade moves freely.
• Do not allow children to play with the remote control.

Battery Recycling Instructions

1. Do not discard coin cell batteries in regular trash.
2. Locate a recycling center (e.g., Call2Recycle).
3. Prepare battery for recycling by taping the positive terminal.
4. Follow local guidelines for disposal.

Legal Information

CE Statement

Hunter Douglas declares compliance with EMC Directive 2014/30/EU, Radio Equipment Directive 2014/53/EU, and Low Voltage Directive 2014/35/EU. Full text available at www.tuiss.com/certifications.

UK Statement

Hunter Douglas declares compliance with Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017, and Electrical Equipment (Safety) Regulations 2016. Full text available at www.tuiss.com/certifications.

FCC Statement

FCC ID: 2BMQ2RW5RW14. Complies with Part 15 of FCC Rules. Operation subject to two conditions: no harmful interference, and acceptance of any interference.

Innovation, Science and Economic Development Canada ICES-003 Compliance

IC: 33385-RW5RW14. Complies with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation subject to two conditions: no interference, and acceptance of any interference.

Quick Start Guide of the Tuiss SmartView App

1. Download the App: Search 'Tuiss SmartView' on App Store or Google Play Store, or scan the QR code.
2. Wake up the motor: Press and hold the setting button at the motor head for 6 seconds.
3. Scan to add blind: Select 'Add my first blind', scan the QR code on the blind's swing label. Confirm by pressing 'Found it!' or 'Jog to identify'.
4. Ready to use: Use 'Open' and 'Close' buttons to move the blind. For individual blinds, select them first.