Yaheetech Cat Tree
Model: 592057
Introduction and Safety
This document provides assembly instructions for the Yaheetech 592057 Cat Tree. Please read these instructions carefully before assembly.
Assembly Tips:
When unpacking and assembling, avoid damaging the product or your floor. The following illustrates common practices:
- ❌ Incorrect: Do not discard parts carelessly or assemble without protection.
- ✔️ Correct: Use a protective pad or cover on the floor and follow the instruction manual to avoid damage during assembly.
General Recommendations:
- Assembly is recommended for 1 or more people.
- Estimated assembly time: 1 hour.
- Keep away from fire or heat sources.
- Not intended for use by children.
- Wearing protective gloves is recommended during assembly.
Parts List
Identify all parts before beginning assembly:
- ① Base Plate (x1)
- ② Corner Panel (x1)
- ③ Top Platform (x1)
- ④ Middle Platform (x1)
- ⑤ Small Round Platform (x1)
- ⑥ Cat Bowl (x1)
- ⑦ Long Sisal-Covered Post (x2) - 40cm
- ⑧ Medium Sisal-Covered Post (x1) - 40cm
- ⑨ Short Sisal-Covered Post (x1) - 18cm
- ⑩ Short Sisal-Covered Post (x1) - 20cm
- ⑪ Medium Sisal-Covered Post (x1) - 27cm
- ⑫ Short Post (x2) - 12cm
- ⑬ Short Post (x1) - 20cm
- ⑭ Small Wooden Dowel (x3) - 23cm
- A Screw (x19)
- B Long Screw (x2)
- C Wall Anchor Set (x1)
- D Allen Wrench (x1)
Assembly Steps
Step 1
Attach the corner panel (②) to the base plate (①) using three dowels (⑭) and six screws (A).
[Diagram: Corner panel being placed onto the base plate, with arrows indicating screws (A) and dowels (⑭) being inserted into pre-drilled holes.]
Step 2
Attach the three posts (⑦, ⑦, ⑧) and one short post (⑨) to the base plate (①) using four screws (A).
[Diagram: Base plate shown with holes. Posts (⑦, ⑦, ⑧, ⑨) are positioned and secured with screws (A) from underneath.]
Step 3
Attach the assembled base structure to the corner panel (②) using one screw (A). Attach the cat bowl (⑥) to the corner panel using three screws (A).
[Diagram: The corner panel assembly is connected to the base structure. The cat bowl (⑥) is attached to the corner panel.]
Step 4
Insert two short posts (⑫) and one short post (⑬) into the top of the corner panel assembly. Secure with three screws (A).
[Diagram: Short posts (⑫, ⑫, ⑬) are inserted into the top of the assembled structure and secured with screws (A).]
Step 5
Attach the middle platform (④) using one screw (A). Attach the cat bowl (⑥) to the middle platform using one screw (B). Attach the 20cm post (⑩) and 27cm post (⑪) to the middle platform using one screw (B) each.
[Diagram: Middle platform (④) attached with screw (A). Cat bowl (⑥) attached to platform with screw (B). Posts (⑩) and (⑪) attached to platform with screws (B).]
Step 6
Attach the top platform (③) to the structure using two screws (A).
[Diagram: Top platform (③) being attached to the uppermost posts with screws (A).]
Step 7
For stability, it is recommended to secure the cat tree to a wall using the provided wall anchor set (C).
[Diagram: Illustration showing the top of the cat tree being secured to a wall using wall anchors (C) and screws.]
Support and Information
For assistance or further information, please contact Yaheetech customer service:
Email: help@yaheetech.shop
Visit our website: www.yaheetech.de
Downloadable manual available at: www.yaheeshop.com/pdf/all-1-5012496.pdf
