Important Information
EN: Please read this instruction manual carefully before attempting to install.
[1 or more people recommended] for assembly.
[Assembly time: approximately 1 hour].
[Not intended for use by children].
[Keep away from fire or other heat sources].
[We recommend wearing protective gloves] during assembly.
Please use a protective pad or cover on your floor to avoid damage during assembly.
Parts List
- Part 1: Allen Wrench (x1)
- Part 2: Screw (16mm) (x4)
- Part 3: Screw (25mm) (x1)
- Part 4: Screw (35mm) (x13)
- Part 5: Drill bit (x3) [for wall mounting]
- Part 6: Metal Bracket (x2)
- Part 7: Large Base Platform (x1)
- Part 8: Side Panel with Archway (x1)
- Part 9: Cat Bowl (x1)
- Part 10: Hanging Toy Ball (x1)
- Part 11: Short Support Pole (34cm) (x2)
- Part 12: Enclosed Cat House/Cave (x1)
- Part 13: Sisal Scratching Board (x1)
- Part 14: Short Support Pole (34cm) (x2)
- Part 15: Medium Support Pole (40cm) (x1)
- Part 16: Short Support Pole (31cm) (x1)
- Part 17: Short Support Pole (26.5cm) (x1)
- Part 18: Short Support Pole (27cm) (x3)
- Part 19: Short Support Pole (34cm) (x2)
- Part 20: Wall Mounting Kit (Anchors and Screws) (x1 set)
Assembly Instructions
- Step 1: Attach the enclosed cat house (12) to the side panel with an arch (8) using six screws (4) and three short poles (18).
- Step 2: Assemble the base: Attach two short poles (11) and two short poles (14) to the large base platform (7) using four screws (4) for each pole. Attach one short pole (19) to the base platform (7) using three screws (4).
- Step 3: Attach the top platform (6) to the side panel with an arch (8) using four screws (2). Attach the sisal scratching board (13) to the side panel with an arch (8) using two metal brackets (6) and two screws (2).
- Step 4: Attach the remaining two short poles (19) to the structure using screws (4). Attach the medium support pole (15) and the short support pole (16) using screws (5). Secure the scratching board (13) using screws (19).
- Step 5: Attach the cat bowl (9) to the top platform using screw (3). Attach the hanging toy ball (10) to the top platform using screw (5). Attach the short support pole (17) using screw (5).
- Step 6: Attach the short support pole (16) to the structure using screw (4).
- Step 7: Attach the second hanging toy ball (10) to the structure using screws (4).
- Step 8: For safety and stability, secure the cat tree to a wall using the provided wall mounting kit (20). This involves drilling holes, inserting anchors, and screwing the unit to the wall.
Product Care Instructions
- Use a soft, clean cloth or sponge to gently wipe the outer surface of the product to remove dust and dirt.
- Avoid using chemical cleaners or harsh solvents to prevent damage to the appearance of the product.
- Inspect the fittings (bolts, screws, nuts, etc.) every 3 months and re-tighten them every 6 months.
- Avoid direct sunlight.
If the product shows structural damage or poses a safety hazard, stop using it until it is repaired.
Important Note
Please remove the bell(s) from the hanging toy balls if your cats tend to eat foreign objects.
Customer Support
If you are not entirely satisfied with your purchase, please feel free to contact us using the following steps:
- Go to Your Orders.
- Find your order in the list.
- Select Problem with order.
- Choose your topic from list displayed.
- Select Contact seller.
US: YAHEE TECHNOLOGIES CORP Address: 1532 S VINEYARD AVE ONTARIO CA 91761
UK: Monumart Limited Address: Europa House, Europa Way, IP15DL, Ipswich.
Manufacturer Information
You can also download the electronic Installation Manual from the Product guides and documents section of the advertising page.
Manufactured in PRC for Yahee GmbH
Yahee GmbH Höpfigheimer Straße 11, 74321 Bietigheim-Bissingen
E-Mail: info@yaheetech.shop
