Embedded RFID Access Control

Introduction

The device is a single door standalone access control with Wiegand input & output. Card read (125KHz) and PIN (4-6 digits) access. It uses Atmel MCU assuring stable performance. The operation is very user-friendly, and low-power circuit makes it long service life.

Optional Version: The device with Bluetooth-enabled. People can install the Bluetooth APP to easily access the door with their smartphone. (APP operation can refer to APP manual)

Features

Waterproof, conform to IP66
Vandal resistant metal enclosure
One relay (990 common users, 990 common + 10 visitor)
Can add any 4-6 digits PIN, Infrared Remote Control
Card Type: 125KHz EM Card/13.56MHz Mifare Card (optional)
Wiegand 26 bits output, Wiegand 26/34bits input automatic identification
Tri-color LED status display
Pulse mode, Toggle mode
Low temperature resistance (-40°C)

Specifications

Parameter	Value
User Capacity	1000
Common User	990
Visitor User	10
Operating Voltage	12-18V DC
Working Current	<=150mA
Idle Current	<=60mA
Proximity Card Reader	EM or Mifare
Read Range	2-5cm
PIN Length	4-6 digits
Wiring Connections	Relay Output, Exit Button, Wiegand Input/Output, Wiegand Output
Relay	Adjustable Output Time 0-99 Seconds (5-seconds default)
Lock Output Load	2 Amp Maximum
Wiegand Interface	Wiegand 26 bits output, Wiegand 26/34bits input automatic identification
Environment	Outdoor (Meets IP66)
Operating Temperature	-40°C ~ 60°C (-40°F ~ 140°F)
Operating Humidity	0%RH~98%RH
Physical	Stainless Steel Plate
Surface Finish	Silver & Black
Dimensions	115x40x25mm (Rectangle), 86x86x25mm (Square)
Unit Weight	230g
Shipping Weight	270g

Carton Inventory

Diagram of a rectangular unit.
Diagram of a square unit.
Diagram of an infrared remote control.
Diagram of a master card.
Diagram of screw cover stickers.
Diagram of self-tapping screws.
Diagram of wall anchors.
Diagram of Diode 1N4004 (for relay circuit protection).

Installation

Drill two holes (A,C) on the wall for the screws and one hole for the device.
Knock the supplied rubber bungs into the screw holes (A,C).
Thread the cable through hole (B).
Attach the unit to the hole (B).
Fix the unit firmly on the wall with two flat head screws.
Cover the screws with Screw Cover Stickers.

Basic Configure

Enter and Exit Program Mode

Programming Step	Keystroke Combination
Enter Program Mode	* (Master Code) # (Factory default is 123456)
Exit Program Mode	*

Set Master Code

Programming Step	Keystroke Combination
1. Enter Program Mode	* (Master Code) #
2. Update Master Code	0 (New Master Code) # (Repeat New Master Code) # (Master code is any 6 digits)
3. Exit Program Mode	*

Connection Diagram

Common Power Supply

Diagram showing connections for Power Supply (12-18V DC), GND, NO, NC, COM, Red, Black, Brown, Grey, Yellow, Green, White wires. Labels include "Magnetic Lock", "Fail-safe Lock", "Exit Button".

Wiring

Colour	Function	Notes
Red	Power +	12~18V DC Votes DC Regulated Power Input
Black	GND	Ground
Blue	NO	Normally Open
Brown	COM	Common Connection for Relay Output
Grey	NC	Normally Close
Yellow	OPEN	Request to Exit (REX)
Green	D0	Wiegand Input/Output Data 0
White	D1	Wiegand Input/Output Data 1

Sound and Light Indication

Operation Status	LED	Buzzer
Stand by	—	—
Enter into programming mode	Red light	One beep
In the programming mode	Red light	One beep
Operation error	Red light	Three beeps
Exit from the Programming mode	Green light	One beep
Open lock:	Green light	One beep
Alarm	Red light shines quickly	Beeps

Controller Mode

(The device Operates as a Controller)

It supports Wiegand 26 bits input (Automatic Identification), so an external Wiegand device (26/34 bits output) can be connected to the device. Either an EM card reader (125 KHz) or a Mifare card reader (13.56MHz) can be connected to the device.

Cards are required to be added at the external reader, except where an external Wiegand Card Reader is used, in this case cards can be added at either a reader or controller.

Wiegand Mode

Pass-through Mode

(The device Operates as a Wiegand Reader)

In this mode the device supports a Wiegand 26 bits output. Wiegand data lines can be connected to any controller which supports a Wiegand 26 bits input, and then the device will operate as a slave reader.

Diagram showing connections for Wiegand device, Special Power Supply, Red, Black, Brown, Grey, Yellow, Green, White wires. Labels include D0, D1, GND, V+, COM, NO, NC, OPEN.

Others

Users Operation & Reset to Factory Default

Open the door: Read valid card user or input valid PIN user.
Active Alarm: Enter Master code or Card or valid card / PIN user.
To reset to factory default & Add Master Card: Power off, press the Exit button, hold it and power on, there will be two beeps, then release the exit button, the LED light turns into yellow, then read any 125KHz EM card / 13.56MHz Mifare card, the LED will turn into red, means reset to factory default successfully. Of the card reading, it is the Master Card.

Master Card Usage

Using Master Card to add and delete users


Add Card / PIN Users	1. Input (Master Card) 2. Input (Card) or (PIN #) Repeat step 2 for additional users 3. Input (Master Card) again
Delete Card / PIN Users	1. Input (Master Card Twice within 5s) 2. Input (Card) or (PIN #) Repeat step 2 for additional users 3. Input (Master Card) again

Notes

----------------------------------------------------------------------------------------------------

Simplified Instruction

Function Description	Operation
Enter the Programming Mode	* - Master Code - # (Input you can do the programming (123456 is the factory default master code)
Change the Master Code	0 - New Code - # - Repeat the New Code - # (code: 6 digits)
Add User	1 - Read Card - # (can card slots continuously)
Add PIN User	1 - PIN - # (The PIN is any 4-6 digits except 8888 which is reserved.) (Input PIN on the Infrared Remote Control)
Delete User	2 - Read Card - # OR 2 - User ID - # OR 2 - By Card number # OR 2 - ALL Users
Exit from the Programming Mode	*
How to release the door	Card User: Read Card PIN User: Input PIN #

Add Common Users

PIN Length: 4-6 digits except 8888.

Add Card User

Programming Step	Keystroke Combination
1. Enter Program Mode	* (Master Code) #
2. Using Auto ID (Allows the device to assign Card to next available User ID number)	1 (Read Card) # (Input 8/10/17 Digits Card Number) # (The cards can be added continuously.)
OR
2. Select Specific ID (Allows Master to define a specific User ID to associate the Card to)	1 (User ID) # (Read Card) # (Input 8/10/17 Digits Card Number) # (The cards can be added continuously.)
OR
2. Add Card; Block Enrollment (Allows Master to add up to 988 cards to the Reader in a single step) Takes 2 minutes to program.	1 (User ID) # (Card Quantity) # (The First Read Card 8/10/17 Digits Number) # (Cards' quantity must be consecutive; Card quantity is the number of cards to be enrolled)

Add PIN User

Programming Step	Keystroke Combination
1. Enter Program Mode	* (Master Code) #
2. Using Auto ID (Allows the device to assign PIN to next available User ID number)	1 (PIN) # (The PINs can be added continuously.)
OR
2. Select Specific ID (Allows Master to define a specific User ID to associate the PIN to)	1 (User ID) # (PIN) #

Add Visitor Users

User ID is 990~999; PIN length: 4-6 digits except 8888. There are 10 groups Visitor/PIN card, the users can be specified up to 10 times of usage, after a certain number of times, i.e. 5 times, the PIN become invalid automatically.

Programming Step	Keystroke Combination
1. Enter Program Mode	* (Master Code) #
2. Add Card	1 (Read Card) # OR 1 (PIN) #
3. Exit	*

Change PIN Users