OSDP Reader User Manual
Model: XK6-RX
1. Introduction
This document provides information on the waterproof OSDP keypad reader, which features Wiegand output and supports 125KHz EM, HID, and 13.56MHz Mifare cards.
Features:
- Waterproof, conforms to IP66
- OSDP+ Wiegand, AES128 encryption
- Card Types Supported: 125KHz HID, EM & 13.56MHz Mifare
- Programmable Wiegand Output: EM card (26~44 bits, default 26), Mifare card (26~44, 56, 58 bits, default 34), HID card (26~37 bits)
- PIN Output: 4 bits, 8 bits, or virtual card number
Specifications:
| Specification | Value |
|---|---|
| Operation Voltage | 12-18V DC |
| Standby Current | ≤50mA |
| Frequency | 125KHz & 13.56MHz |
| Card Type | EM & HID & MIFARE |
| Read Range | 2~4 cm |
| Wiegand Output Format | EM card: Wiegand 26~44 bits output (default: 26bits) Mifare card: Wiegand 26~44, 56, 58bits output (default: 34bits) HID card: Wiegand 26~37 bits output |
| Keypad Transmission Format | 4 bits (factory default) / 8 bits or virtual card number |
| Operating Temperature | -40°C~60°C |
| Operating Humidity | 0%~98% RH |
| Color | Black |
| Index of Protection | IP66 |
| Dimension | 120x75x20mm (Wide) / 120x50x20mm (Slim) |
| Net Weight | 200g (Wide) / 150g (Slim) |
| Shipping Weight | 250g (Wide) / 200g (Slim) |
2. Installation
Follow these steps for installation:
- Drill two holes (A, C) on the wall for the screws and one hole (B) for the cable.
- Insert rubber bungs into holes (A, C).
- Fix the back cover on the wall using two screws.
- Thread the cable through the cable hole (B).
- Attach the unit to the back cover.
Wiring:
| Color | Function | Notes |
|---|---|---|
| Red | Power + | +12V |
| Black | GND | Ground |
| Green | DO | Data 0 |
| White | D1 | Data 1 |
| Brown | LED | Green LED Light Control |
| Yellow | Buzzer | Buzzer Control |
| Blue | A | RS485A |
| Gray | B | RS485B |
3. Programming
When in program mode, press '*' for 5 seconds, then enter the Master Code followed by '#'. The factory default Master Code is '123456'.
Set Wiegand Format for EM Cards
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Set Wiegand Format | 1 (26~44) # (Factory default is 26bits) |
| 3. Exit Program Mode | *(Master Code) # |
Set Wiegand Format for HID Cards
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Output Format Setting | 2 (26~37) # |
| 3. Exit Program Mode | *(Master Code) # |
Set Wiegand Format for MIFARE Cards
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Output Format Setting | 3 (26~44, 56, 58) # (Factory default is 34 bits) |
| 3. Exit Program Mode | *(Master Code) # |
Set PIN Output Format
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. PIN output | 40# (4 bits) / 44# (factory default) / 48# (8 bits) |
| 3. Exit Program Mode | *(Master Code) # |
Set Keypad Backlit
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Keypad Backlit | 51# (Always ON) / 52# (Automatic OFF after 20s) |
| 3. Exit Program Mode | *(Master Code) # |
Baud Rate Settings (Factory default: 9600)
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Setting values | 6 (4800, 9600, 14400, 19200, 38400, 56000, 57600, 115200, 128000) # |
| 3. Exit Program Mode | *(Master Code) # |
Note: The baud rate of all readers under the same controller must match the controller's baud rate for successful connection.
OSDP Address Settings (Factory default: 0)
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Setting the address | 7 (0-126) # |
| 3. Exit Program Mode | *(Master Code) # |
Note: OSDP reader addresses under the same controller must be unique to avoid conflicts.
Reset to Factory Default (two methods)
Method 1
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Reset to Factory Default | 50 # |
| 3. Exit Program Mode | *(Master Code) # |
Method 2 (Forgetting Master Code)
Power off the device. Connect the Yellow wire (Buzzer Control) and GND wire. Power on the device. After 5 seconds, a long beep will indicate a successful reset. Disconnect the Yellow and GND wires.
Update Master Code
| Programming Step | Keystroke Combination |
|---|---|
| 1. Enter Program Mode | *(Master Code) # |
| 2. Update Master Code | 0 (New Master Code) # (Repeat New Master Code) # |
| 3. Exit Program Mode | *(Master Code) # |
4. Indicator light status
| Operation Status | Indicator light color | Buzzer |
|---|---|---|
| Standby status | OSDP Controller decides | OSDP Controller decides |
| Correct Card | OSDP Controller decides | Beep |
| Error Card | OSDP Controller decides | Beep |
5. Packing List
| Name | Quantity |
|---|---|
| Reader | 1 |
| Manual | 1 |
| Self Tapping Screws (4x25mm) | 2 |
| USB Serial Tools | 2 |
| Rubber plug | 2 |
Diagram Descriptions
Front Panel Diagram
The front panel of the reader shows a keypad with numbers 0-9, *, #, and directional arrows. It is presented in two form factors: 'Wide' and 'Slim'.
Installation Diagram
The installation diagram illustrates drilling points (A, C for screws, B for cable) on a wall, inserting wall plugs, mounting the back cover, threading the cable, and attaching the reader unit.
Connection Diagram (OSDP)
The OSDP connection diagram shows reader terminals (Red for Power+, Black for GND, Blue for RS485A, Gray for RS485B) connecting to corresponding controller terminals.
Connection Diagram (Wiegand)
The Wiegand connection diagram shows reader terminals (Red for Power+, Black for GND, Green for DO, White for D1) connecting to corresponding controller terminals.
