S-RX Series RFID Readers
User Manual
1. Introduction
The S-RX Series readers are advanced 125 KHz & 13.56 MHz technology proximity readers, with built-in Light Dependent Resistor (LDR) sensor for anti-tamper. They are an ideal choice for high-security applications. They are attractively designed with a thin profile and modern appearance, with four models (S1-RX, S2-RX, S3-RX and S4-RX) available.
2. Specifications
| Model | S1-RX | S2-RX | S3-RX | S4-RX |
|---|---|---|---|---|
| Operation Voltage | 9~24V DC | |||
| Standby Current | <25mA | |||
| Frequency | 125KHz and 13.56MHz | |||
| Card Type | 125KHz - EM & HID Card/Fobs 13. 56Mhz - Mifare Card (ISO 14443A Compatible) | |||
| Read Range | Up to 2.8 inches (7cm) | |||
| Output Format | 26 bits Wiegand (default) 26~37 bits available upon request | |||
| Operating Temperature | -40°C~60°C (-40°F~140°F) | |||
| Operating Humidity | 10% to 95% RH | |||
| Color | Black (White optional) | |||
| Index of Protection | IP66 | |||
| Dimension(H x W x T) | 103x48x20 mm | 103x48x20 mm | 120x48x20 mm | 120x76x20 mm |
| Net Weight | 100g | 100g | 120g | 150g |
| Shipment Weight | 150g | 150g | 170g | 200g |
3. Installation
- Drill 2 holes (A, C) on the wall for the screws and one hole for the cable.
- Knock the rubber bungs to the holes (A, C).
- Fix the back cover on the wall with 2 screws.
- Thread the cable though the cable hole (B).
- Attach the unit to the back cover.
Installation Diagram Description: The diagram illustrates the mounting process in three steps. Step 1 shows a wall with marked points for drilling: two 5mm holes (A and C) for screws and one 10mm hole (B) for the cable. The wall height is indicated as 70mm. Step 2 shows the back cover being fixed to the wall with screws. Step 3 shows the reader unit being attached to the back cover after threading the cable through hole B.
Wiring
| Color | Function | Notes |
|---|---|---|
| Red | Power | +DC (9-24V DC) |
| Black | GND | Ground |
| Green | D0 | Data 0 |
| White | D1 | Data 1 |
| Brown | LED | Green LED Light Control |
| Yellow | Buzzer | Buzzer Control |
(Remarks: Brown and Yellow wires are optional connections)
Connection Diagram Description: The diagram shows a reader unit with multiple wires connecting to an access controller. The reader's wires are color-coded: Red for +DC (9-24V DC), Black for Ground (GND), Green for Data 0 (D0), White for Data 1 (D1), Brown for LED control, and Yellow for Buzzer control.
4. Functions Table Sheet
| Read Card | The LED light will turn into Green, and the buzzer sounds a beep, at the meantime, the reader outputs the Wiegand signal. |
| External LED Control | When the input voltage for LED is low, the LED will turn into Green. |
| External Buzzer Control | When the input voltage for Buzzer is low, the Buzzer will sounds. |
| Wiegand Data Output | Wiegand 26~37 bits range available for S-RX Series readers, factory default setting is Wiegand 26 bits. HID card can output Wiegand 26~37 bits automatically, EM and Mifare cards are forced to output based on the reader setting. |
5. Data Signal
| Description | S-RX Series Reader Typical Time |
|---|---|
| Pulse Width Time | 42 µS |
| Pulse Interval Time | 2 mS |
The table shows the typical timing for the Wiegand data output from the readers. The data signal diagram illustrates the waveform for pulse width time (duration of a pulse) and pulse interval time (time between pulses), with D0 and D1 signals transitioning between +5V and 0V. D0 has a pulse width of 42µS, and the pulse interval is 2mS.
Packing List
| Name | Quantity |
|---|---|
| Reader | 1 |
| Manual | 1 |
| Screw Driver | 1 |
| Wall Fixing Plugs | 2 |
| Self Tapping Screws | 2 |
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Warning Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
