LNC LMABIFQ770329C Vanity Light Bar Installation Guide

Important Safety Warnings

• ⚠️ To reduce the risk of fire, electric shock, or personal injury:
  • Installation by a licensed electrician is suggested.
  • Read instructions carefully and save for future reference.
  • Turn off electricity at the main fuse or circuit breaker box and place the wall switch in the "OFF" position before starting any work.
  • The mounting surface should be clean, dry, flat, strong enough, and at least 1/4" larger than the canopy on all sides. Correct any gaps between the mounting surface and canopy exceeding 3/16".
  • Ensure the ceiling or wall can support the lamp's weight before installation.
  • Verify the voltage is 120V. The maximum wattage is Type B, Max 40W per bulb.
  • Keep the lamp away from acidic and alkaline substances to prevent surface damage.
  • When replacing bulbs, turn off or unplug the lamp and wait until it is cool, as bulbs get hot quickly.
  • These safety instructions are not exhaustive; common sense, caution, and care must be used with any electrical products.

Tools Required (Not Included)

• Ladder
• Phillips Head Screwdriver
• Electrical Tape
• Pliers
• Wire Cutter/Stripper

Parts Included

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Back plate (1)
• (F) Knob nut (2)
• (G) Socket (4)
• (H) Lampshade (4)

Assembly & Installation Instructions

Step 1: Preparation

• Carefully remove the fixture from the carton and check that all parts and accessories are included.
• Turn off power at the main fuse/circuit breaker box and the wall switch before starting installation.

Step 2: Mounting Plate Installation

• Unscrew knob nuts (F) from back plate (E) and mounting plate (D); set them aside.
• Pass the supply wires from the outlet box through mounting plate (D).
• Secure mounting plate (D) to the outlet box using mounting screws (A).

Step 3: Wire Connections

• Connect wires as shown in the wiring chart. Ground wire is bare copper; never connect other wires to ground wires.
• Ground Wire Connection: Connect the outlet box ground wire to the fixture ground wire and the green ground screw (C) on the mounting plate.
• Supply Wire Connection:
  • Connect the "Hot" wire (typically black, parallel cord smooth/round) from the supply to the socket wire (typically black or brown, clear/gold/black without tracer).
  • Connect the "Neutral" wire (typically white, parallel cord ridged/square) from the supply to the socket wire (typically white, clear/brown/gold/black with tracer).
  • *Note on parallel wires (SPT I & SPT II): The neutral wire is square-shaped or ridged, and the other wire is round in shape or smooth.*
• Twist wires together with plastic wire connectors (B) until tightly joined. Wrap each connector with approved electrical tape, ensuring no wire strands are exposed.
• Carefully tuck all wires into the outlet box.

Step 4: Attach Back Plate

• Align the holes in back plate (E) with the pre-assembled mounting screws on mounting plate (D).
• Attach back plate (E) to mounting plate (D) using the knob nuts (F) previously removed. Hand tighten until snug.
• Adjustment Note: If back plate (E) is not snug against the wall, remove it and adjust the threaded length of the pre-assembled mounting screws on mounting plate (D) by loosening/tightening the hex nuts. Re-attach and check for snugness.

Step 5: Install Bulbs and Lampshades

• Install bulbs (not included). Do not exceed the maximum wattage recommended on the socket (Type B, Max 40W).
• Carefully screw lampshades (H) onto sockets (G).

Final Check

• Verify that everything is installed properly.
• Turn on the light. Enjoy!

Ordering Replacement Parts

• Keep this sheet for future reference in case you need to order replacement parts.
• All parts for this fixture can be ordered from the place of purchase. Be sure to use the exact wording from the illustration when ordering parts.

Cleaning Instructions

• To clean, wipe the fixture with a soft cloth.
• Clean glass with a mild cleaner, such as mild and non-abrasive soap.
• Do not use abrasive materials such as scouring pads, powders, steel wool, or abrasive paper.