LNC Charm 4-Light Vanity Light Bar Installation Guide

Warnings and Safety Instructions

⚠️ WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them for future reference.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse or circuit breaker box in your home.
   • Place the main power switch in the "OFF" position.
   • Place the wall switch in the "OFF" position.
4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16" should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Ensure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances to prevent damage to the lamp's surface.
8. When replacing bulbs, turn off or unplug the lamp and wait until it is cool, as bulbs get hot quickly.
9. The safety instructions in this manual are not exhaustive and may not cover all possible conditions. Common sense, caution, and care must be used with any electrical products.

Image for Finished Product

An illustration showing the assembled LNC Charm 4-Light Vanity Light Bar. It features four arms extending horizontally from a central back plate, each holding a clear glass shade. The fixture has a matte gold finish.

Tools Required (Not Included)

Before starting assembly and installation, please prepare the needed tools as shown below:

• [Ladder]
• [Phillips head/flat blade screwdriver]
• [Electrical tape]
• [Pliers]
• [Wire cutter/Stripper]

Parts Type & Quantity Including

• (E) Mounting plate (1)
• (F) Green ground screw (1)
• (G) Back plate (1)
• (H) Arm (4)
• (I) Iron frame (4)
• (J) Screw (12)
• (K) Knob nut (2)
• (L) Glass shade (4)

Diagram Description: A visual representation of the fixture's components, showing the mounting plate, back plate, arms, iron frames, glass shades, screws, knob nuts, and ground screw.

Accessories & Quantity Enclosed

• (A) Plastic wire connector (3)
• (B) Anchor (2)
• (C) Mounting screw (2)
• (D) Wood screw (2)

Diagram Description: A visual representation of the included accessories: plastic wire connectors, anchors, mounting screws, and wood screws.

Assembly & Installation Instructions

Step A1 » Unscrew knob nuts (K) from back plate (G) then gently remove mounting plate (E). Then set them aside for later installation.

Diagram Description: Illustration showing the removal of knob nuts (K) from the back plate (G) and the subsequent removal of the mounting plate (E).

Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (E).

NOTE: To drill the holes on the wall for anchors (B):

• Attach mounting plate (E) to the outlet box with mounting screws (C) and mark the holes.
• Unscrew mounting screws (C) and remove mounting plate (E), drill holes and gently knock anchors (B) into the holes until anchors (B) are level with the wall.
• Secure mounting plate (E) to the outlet box with mounting screws (C) and wood screws (D).

Diagram Description: Shows passing wires through the mounting plate (E) and securing the mounting plate to the outlet box using screws (C) and wood screws (D), with a note on preparing holes for anchors (B).

Step A3 » Make wire connections

Connect wires as shown in the wire connection diagram. PLEASE NOTE THAT THE GROUND WIRE IS A BARE COPPER WIRE; NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart:

Diagram Description: Illustrates connecting the ground wire from the outlet box to the fixture's ground wire, typically a bare copper wire, using a green ground screw. Shows two common scenarios for outlet box and fixture ground wires.

Connect wires according to the below chart:

*Note: When parallel wires (SPT I & SPT II) are used, the neutral wire is square-shaped or ridged and the other wire will be round in shape or smooth (see illustration).

Diagram Description: A visual guide for connecting the main supply wires. It shows that the black or red supply wire connects to the fixture's black wire, and the white supply wire connects to the fixture's white wire. It details how to identify and connect different types of wires, including parallel cords and insulated wires, based on their shape and presence of a tracer. The neutral wire is identified by its square or ridged shape for parallel cords.

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Diagram Description: Shows twisting wires together with plastic wire connectors, wrapping them with electrical tape, and tucking them into the outlet box. It emphasizes ensuring no wire strands are exposed.

Step A4 » Align the holes in back plate (G) with the pre-assembled mounting screws, then attach back plate (G) to mounting plate (E) with the previously removed knob nuts (K). Hand tighten until snug.

Diagram Description: Illustration showing the back plate (G) being aligned with the mounting screws on the mounting plate (E) and secured with knob nuts (K).

Step A5 » 1) Remove screws (J) from iron frames (I). Place glass shades (L) on iron frames (I) and secure them with screws (J). 2) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Diagram Description: Shows removing screws (J) from iron frames (I), placing glass shades (L) onto the frames, and securing them with screws (J). Also indicates the installation of bulbs.

4. Check everything is installed properly, then you could turn on the light. Enjoy!

Ordering Parts

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use the exact wording from the illustration when ordering parts.

Cleaning

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.