Minelab EQUINOX 600/800 Metal Detector Quick Start Guide
Assembly
1. Connecting the Coil to the Lower Shaft
Diagram shows inserting two rubber washers into the yoke's slots, sliding the yoke onto the coil's shaft, aligning the coil connector with the control box slot, and tightening the locking ring.
2. Assembling the Shaft
Diagram shows loosening a twist lock [twist-lock-symbol], sliding the lower shaft into the middle shaft until it clicks [click-symbol], and tightening the twist lock. This is repeated for the middle and upper shafts.
3. Connecting the Handle/Armrest
Diagram shows placing the handle on the upper shaft, aligning holes [hole-alignment-symbol], inserting a screw [screw-symbol], and securing a hand strap with a nylon fastener [nylon-fastener-symbol].
4. Connecting the Coil
Diagram shows wrapping the coil cable around the shafts and securing it with Velcro straps [velcro-symbol].
Battery Charging
The EQUINOX series detectors feature a built-in rechargeable lithium-ion battery. For the fastest charge, turn off the detector while charging.
1. Connect the magnetic charging cable's USB connector to any standard powered USB port.
2. Connect the magnetic charger connector to the slot on the back of the detector's control unit. The charge status LED indicator on the top left of the control unit will flash steadily [charging-indicator-flashing].
3. The charge status LED indicator will remain solid when charging is complete [charging-indicator-solid].
Audio
The EQUINOX series detectors have an external speaker, allowing detection without headphones. Various other audio options are available. Refer to the full manual for more information.
Quick Start: 4 Simple Steps
Note: It is recommended to charge the battery for 4 hours before first use.
1. Power On
Press the power button [power-button-symbol] located on the side of the control unit.
2. Select Detect Mode
Choose the optimal search profile for your location. (Illustration shows EQUINOX 800).
3. Noise Cancel
From the settings menu, select Noise Cancel and press [button-symbol] to initiate automatic noise cancellation. This process takes approximately 8 seconds.
4. Start Detecting!
Press the [button-symbol] to return to the detection screen and begin detecting!
Detection Modes
Each detection mode includes two adjustable search profiles and unique default settings.
Park
Ideal for high-trash recreational areas, including most general detecting.
Field
Ideal for detecting a wide range of targets in historical fields.
Beach
Optimized for all saltwater conditions (dry sand, wet sand, surf, and underwater).
Goldfield*
*This asterisk indicates features exclusive to the EQUINOX 800 model.
Best suited for gold nugget prospecting in mineralized goldfields.
User Interface
Adjust and view detector settings.
Power Button
Short press the power button [power-button-symbol] to turn the detector on or off. Long press for 5 seconds to reset the detector to factory settings.
Backlight
Select backlight brightness* or turn backlight on/off. The backlight icon [backlight-symbol] will be displayed when the backlight is on.
Sensitivity
Adjust sensitivity levels (25 levels) using the [-] and [+] buttons.
Detect Mode Button
Short press to cycle through detection modes [mode-cycle-symbol]. Press and hold for 5 seconds to restore the active search profile to its factory preset.
Detector Settings Menu
Short press the settings button [gear-icon] to enter and cycle through the detector settings menu. Long press the settings button to enter advanced settings (if available). Adjust selected settings using the [-] and [+] buttons.
Wireless Audio
Short press the wireless button [wireless-button-symbol] to turn wireless on/off. Long press to pair wireless audio devices (any Bluetooth headphones, aptX™ Low Latency headphones, or WM 08 wireless audio module). Up to 4 wireless devices can be paired and used simultaneously.
Battery Status
LED indicator shows charging status [battery-status-indicator]. Can detect while connected to a USB power bank, acting like a spare battery.
Sensitivity Indicator
Indicates approximate sensitivity level (25 levels).
Depth Indicator
Indicates estimated target depth (5 levels).
Tracking
Indicates ground balance tracking is in progress [tracking-indicator-symbol].
User Profiles*
Long press the user profile button [user-profile-button-symbol] to save current detector settings. Short press to turn saved user profiles on or off.
Discrimination
High-resolution 50-segment discrimination (-9 to 40) for precise and stable target identification. When a target is detected, press the Accept/Reject button [accept-reject-button-symbol] to instantly accept or reject it. You can also create discrimination patterns via the settings menu. Press [-] or [+] to move to a segment, then press Accept/Reject button to accept or reject it.
Target ID
Target ID -9 to 0 indicates ferrous targets, such as -5. Target ID 1 to 40 indicates non-ferrous targets, such as 32.
Frequency
Displays the current operating frequency. Press the frequency button [frequency-button-symbol] at any time to cycle through the available operating frequencies for the active search profile: 5, 10, 15, 20*, or 40*. Displays the currently selected single frequency (kHz): 5, 10, 15, 20*, or 40*. Displays a square symbol [multi-frequency-symbol] when operating in multi-frequency.
Noise Cancel
Automatic | Manual*
Ground Balance
Automatic | Manual*
Volume
0 to 25
Threshold
0 to 25
Target Tones
1, 2, 5, and 50
Recovery Speed
1 to 3 | 1 to 8*
Iron Bias
0 to 3 | 0 to 9*
All Metal
Press the All Metal button [all-metal-button-symbol] to turn the selected discrimination mode on or off, allowing for target confirmation.
Pinpoint
Helps determine the precise location of a target before recovery. Press the Pinpoint/Detect button [pinpoint-detect-button-symbol] to enable pinpoint mode. Press the button again to return to the detection screen.
Technical Specifications
| Feature | EQUINOX 600 | EQUINOX 800 |
|---|---|---|
| Detection Modes | Park, Field, Beach 6 custom search profiles | Park, Field, Beach, Goldfield* 8 custom search profiles |
| Operating Frequency (kHz) | Multi-frequency, 5, 10, 15 | Multi-frequency, 5, 10, 15, 20, 40 |
| Standard Headphone | 3.5mm (1/8") | 3.5mm (1/8") / Bluetooth® / aptX™ Low Latency |
| WM 08 Module Compatibility | Yes, without WM 08 | Yes, with WM 08 |
| Waterproof Rating | 3m (10 ft) waterproof | |
| Battery Life (Approx.) | 12 hours, charge time approx. 4 hours | |
| Standard Coil | EQX 11 Double-D smart coil | |
| Warranty Conditions | Refer to www.minelab.com/warranty-conditions for full terms. Register online at register.minelab.com. | |
Compliance and Contact Information
FCC Compliance
Information to the user (FCC Rules Part 15.105). This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device must not cause harmful interference; and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: Class B Device. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Warning: Any changes or modifications not expressly approved by Minelab Electronics could void the user's authority to operate this equipment.
Contact Information
Australia and Asia-Pacific: +61 8 8238 0888, minelab@minelab.com.au
Europe and Russia: +353 21 423 2352, minelab@minelab.ie
North, South, and Central America: +1 630 401 8150, minelab@minelab.com
Middle East and Africa: +971 4 254 9995, minelab@minelab.ae
Manufacturer: Minelab Electronics, PO Box 35, Salisbury South, South Australia 5106.
For complete product specifications and operating instructions, please read the full user manual available at www.minelab.com.
Minelab®, EQUINOX®, Wi-Stream™, Multi-IQ®, 5F×8™, and 3F×3™ are trademarks of Minelab Electronics Pty. Ltd. Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc. Qualcomm® aptX™ is a product of Qualcomm Technologies International, Ltd.
