FlinQ Lumifan FQC8420 & FQC8421

Welcome to the FlinQ Family

Thank you for purchasing a FlinQ product. To ensure continuous operation and accuracy, please read these operating instructions carefully before use and save this manual for future reference. Ignoring certain procedures may lead to incorrect reading and use of this product. We hope you enjoy your new FlinQ product! If the item is accidentally damaged, defective, or broken, you are covered by warranty. Please do not hesitate to contact FlinQ & Co B.V. for any questions, concerns, or suggestions.

Register Your FlinQ Product

Register your product for the following benefits:

• 1 year extra warranty (2+1)
• Personal support
• Digital warranty certificate
• Digital manual

Scan the QR code or go to flinqproducts.nl/registration

Safety Information

1. Before using the product, ensure that the voltage is compatible with the working voltage of the item. Using an incorrect voltage can damage the product and create potential safety risks.
2. The light source of this lamp is not user-replaceable. It should be replaced by the manufacturer, the manufacturer's service personnel, or a qualified individual.
3. While the fan is in operation, do not touch the fan blades to prevent danger.
4. The fan lamp should be installed at a height of more than 2.3 meters above the ground.
5. The lamp can be controlled by the remote control. When the lamp is turned off using the remote control, it does not necessarily mean that the power supply is completely cut off. Therefore, it is prohibited to touch, replace, or disassemble the lamp in this situation, as it may lead to electric shock and even cause casualties.

Specifications

Installing the Lumifan / Light

Before plugging the unit into the mains, ensure by visual inspection that the unit is intact and has not suffered any damage during transit.

1. Turn off main power

   Before you start installing the ceiling fan / light, turn off the main power switch.

2. Mark holes on ceiling

   Mark the holes on the ceiling.

3. Insert plugs and place mounting bracket

   Insert the 4 plugs into the drilled holes. Place the mounting bracket and screw the 4 screws into the holes.

4. Insert screws on the side

   Insert the 4 screws into the side. Do not fully tighten each screw on the side; leave it partially loose.

5. Connect the wires

   Connect the wires coming out of your ceiling to the ceiling fan / light. (Typically Live (L - Brown), Neutral (N - Blue), and Ground (Yellow/Green)).

6. Connect fan to mounting bracket

   Connect the product to the mounting bracket placed on your ceiling. Tighten the 4 screws on the side. Insert 1 safety screw on the left side.

7. Turn on main power

   Turn on the main power.

Remote Control Instructions

The remote control is already connected to the device. Insert the batteries and press the on/off button to turn on the fan/light.

Remote Functions:

• 1. Screen: Displays current status.
• 2. All on / off: Turns all functions on or off.
• 3. Pair cord: Used for pairing the remote.
• 4. Fan speed -: Decreases fan speed.
• 5. Brightness -: Decreases light brightness.
• 6. Forward / reverse (fan direction): Changes fan rotation direction.
• 7. Light on / off: Toggles the light.
• 8. Fan speed +: Increases fan speed.
• 9. Color temperature: Adjusts light color temperature (6500K, 4000K, 3000K).
• 10. Brightness +: Increases light brightness.
• 11. Timer: Sets a timer for operation.
• 12. Night Light mode: Activates a low-light mode.

Note: When connecting the lamp to an existing connection linked to a wall switch, ensure the wall switch remains in the ON position after installation. You control the lamp and its on/off function using the remote control.

Cleaning and Maintenance

1. Remove the safety screw on the side of the lamp body. Hold the fan lamp with both hands, push it upward, and rotate it counterclockwise to remove the fan lamp body.
2. Remove the wiring caps, disconnect the wires, and remove the safety steel rope.
3. Clean the protective net and fan blade after opening.

Note: Do not flush the lamp body with water directly. After cleaning, dry it thoroughly. To avoid the risk of falling, please confirm all parts are installed correctly.

Note: Always switch off the power before cleaning near electrical parts (lamps, fan blades, etc.). Wipe up excess moisture with a sponge or cloth to prevent water or liquid from entering electrical parts and causing electric shock. Do not use flammable or toxic cleaning liquids.

Remote Not Connected / Disconnect the Remote

Pairing Your Remote When Not Connected

Connect the device to the power supply and confirm it works normally (light turns on slowly). Turn off the power for 5-10 seconds, then turn it back on. Long press the "FAN OFF" button until the device flashes 3 times quickly, then release. The remote control is now successfully paired and can control the device.

Disconnect the Remote Control

To disconnect the remote control from the fan/lamp (useful if you have multiple fans and want to control them with one remote): Connect the device to power and confirm it works normally. Turn off the power for 5-10 seconds, then turn it back on. Long press the "TIMER" button until the device flashes 3 times quickly, then release. The remote control is now cleared and will no longer control the device. It must be re-paired before use.

Declaration of Conformity

Company: FlinQ & Co B.V.

Address: Eemweg 74, 3755LD Eemnes, The Netherlands

Product: FlinQ Lumifan

FlinQ & Co B.V. declares that the FlinQ Lumifan complies with the safety and hazardous substance restrictions of the relevant European harmonization directives: 2014/53/EU (Radio Equipment Directive - RED) and 2011/65/EU + 2015/863/EU (Reduction of hazardous substances - ROHS), including all modifications.

Conformity is guaranteed by the CE symbol. This product has been tested according to harmonized standards and specifications of EU legislation. The full text of the EU declaration of conformity is available at: www.flinqproducts.nl

Date of Declaration: 05-03-2025

Product Rating: 85-265 V / 50/60 Hz

Product Type: Lights & Lighting > LED Ceiling Fans

Production Date: 2025

Produced in: China