FlinQ Smart Indoor AeroGlow

Welcome to the FlinQ Family

Thank you for purchasing a FlinQ product. Please read this manual carefully for continuous operation and accuracy. Save this manual for future use. If the item is damaged, defective, or broken, you are covered by warranty. Contact FlinQ for any questions or concerns.

Register your FlinQ product for:

• 1 year extra warranty (2+1)
• Personal support
• Digital warranty certificate
• Digital manual

Scan the QR code or visit flinqproducts.nl/registration

Safety Information

1. Ensure voltage compatibility to prevent product damage and safety risks.
2. The light source is not user-replaceable and must be replaced by the manufacturer or qualified personnel.
3. Do not touch fan blades during operation to prevent danger.
4. Install the fan lamp at a height of more than 2.3 meters above the ground.
5. The lamp can be controlled via remote or mobile app. Turning off the lamp does not necessarily cut off power. Do not touch, replace, or disassemble the lamp in this state to avoid electric shock.

Specifications

Installing the AeroGlow

Before plugging in, visually inspect the unit for damage.

1. Turn off main power: Switch off the main power before installation.
2. Mark holes on ceiling: Mark the desired locations for mounting.
3. Insert plugs and place mounting bracket: Insert 4 plugs into the drilled holes. Place the mounting bracket and screw in 4 screws.
4. Insert screws on the side: Insert 4 side screws, leaving them slightly loose.
5. Connect the wires: Connect the wires from your ceiling to the fan/light.
6. Connect fan to mounting bracket: Attach the product to the mounting bracket. Tighten the 4 side screws. Insert 1 safety screw on the left side.
7. Turn on main power: Restore power and proceed to connect to the FlinQ app.

Connect the AeroGlow to the FlinQ App

Note: Only 2.4 GHz networks are supported. 5 GHz networks will not work.

1. Open the FlinQ app: Launch the FlinQ app on your mobile device.
2. Add the device: Select 'Add Device' or the '+' icon. Ensure the fan light is flashing. If not, turn the wall switch on and off 5-10 times until it flashes. Proceed when flashing.
3. Select product type: In the 'Cooling' tab, select 'FlinQ Smart Indoor AeroGlow'.
4. Reset (if needed): If the light is flashing, proceed. If not, repeat the on/off cycle 5-10 times until it flashes.
5. Fill in the WiFi details: Enter your WiFi name and password.
6. Device is being added: The device installation may take up to 2 minutes.
7. Device added successfully: The device is now added to your product list and can be controlled remotely.

Remote Control Instructions

The remote is pre-connected. Insert batteries and press the on/off button. If not connected, turn on the light and press the on/off button for 5 seconds until the light flashes 3 times.

Remote Buttons:

• 1. On/Off: Turns the fan/light on or off. Long press (5 seconds) for app pairing.
• 2. Natural Wind: Selects natural wind mode.
• 3. Forward/Reverse: Changes fan direction.
• 4. No Function.
• 5. Fan On/Off: Turns the fan on or off.
• 6. Fan Speed: Adjusts fan speed across 6 levels.
• 7. Main Light On/Off: Turns the main white light on or off.
• 8. Night Light Mode: Activates night light mode.
• 9. Brightness +/-: Adjusts brightness in 10 levels or steplessly.
• 10. Color Temperature +/-: Adjusts color temperature in 10 levels or steplessly.
• 11. Color Cycle: Cycles through yellow (3000K), neutral (4000K), and white (6500K) light.
• 12. Brightness 50%/100%: Toggles between 50% and 100% brightness.
• 13. Timer Mode: Sets a 1 or 4-hour timer to turn off the fan and lights.

Note: If connected to a wall switch, leave the switch ON. Repeatedly turning the wall switch on/off will reset the AeroGlow, requiring re-pairing with the app.

Cleaning and Maintenance

1. Remove the safety screw, push the lamp body upward, and rotate counterclockwise to detach it.
2. Remove wiring caps, disconnect wires, and remove the safety steel rope.
3. Clean parts after opening and removing protective net and fan blades.

Note: Do not rinse the lamp body with water. Dry thoroughly after cleaning. Ensure parts are correctly installed to prevent falling. Always switch off power before cleaning electrical parts. Wipe excess moisture to prevent electric shock. Do not use flammable or toxic cleaning liquids.

Remote Control Not Connected / Disconnecting the Remote

Pairing Remote: Connect device, verify normal function (light on slowly). Turn off power for 5-10 seconds, then turn on. Long press the on/off button until the device flashes 3 times quickly. Release. Pairing is successful.

Disconnecting Remote: Connect device, verify normal function (light on slowly). Turn off power for 5-10 seconds, then turn on. Long press the on/off button until the device flashes 3 times quickly. Release. The remote is cleared and needs re-pairing.