FlinQ Lumifan Instruction Manual

Welcome to the FlinQ Family

Thank you for choosing one of our products! To ensure continuous operation and accuracy, please read these operating instructions carefully before use and save this manual for future reference. Skipping certain procedures may lead to incorrect reading and misuse of this product. We hope you enjoy your new FlinQ product! If the item is accidentally damaged, defective, or broken, you are covered by warranty! Please do not hesitate to contact us with any questions, concerns, or suggestions at the email address provided in this manual.

Register Your FlinQ Product

We understand you want to take good care of your FlinQ item. Register your product for free and benefit from:

• 1 year extra warranty (2+1)
• Personal support
• Digital warranty certificate
• Digital manual

Scan the QR code or visit flinqproducts.nl/registration

Safety Information

1. Before using the product, ensure the voltage is compatible with the item's working voltage. Using incorrect voltage can damage the product and create potential safety risks.
2. The light source of this lamp is not user-replaceable. It must be replaced by the manufacturer, their service personnel, or a similarly qualified individual.
3. Do not touch the fan blades while the fan is in operation to prevent danger.
4. The fan lamp should be installed at a height of more than 2.3 meters above the ground.
5. The lamp can be controlled by the remote control. When the lamp is turned off using the remote control, it does not necessarily mean the power supply is completely cut off. Therefore, it is prohibited to touch, replace, or disassemble the lamp in this situation, as it may lead to electric shock and even cause casualties.

Specifications

Installation Instructions

Before plugging the unit into the mains, ensure by visual inspection that the unit is intact and has not suffered any damage during transit.

1. Turn off main power: Before starting installation, turn off the main power switch.
2. Mark holes on ceiling: Mark the desired locations for mounting holes on the ceiling.
3. Insert plugs and place mounting bracket: Insert the 4 provided plugs into the drilled holes. Position the mounting bracket and secure it with 4 screws.
4. Insert screws on the side: Insert the 4 side screws into the bracket. Do not fully tighten them; leave them partially loose for now.
5. Connect the wires: Connect the wires coming from your ceiling to the corresponding wires on the fan/light. (Diagram shows L-brown, N-blue, Ground-yellow/green).
6. Connect fan to mounting bracket: Attach the fan/light unit to the mounted bracket. Tighten the 4 side screws securely. Insert the safety screw on the left side.
7. Turn on main power: Restore the main power supply.

Remote Control Instructions

The remote control is pre-paired. Insert batteries and press the on/off button to operate.

Remote Functions:

• 1. Screen
• 2. All on / off
• 3. Pair cord
• 4. Fan speed -
• 5. Brightness -
• 6. Forward / reverse (fan direction)
• 7. Light on / off
• 8. Fan speed +
• 9. Color temperature (6500K/4000K/3000K)
• 10. Brightness +
• 11. Timer
• 12. Night Light mode

Note: If connecting to a switched outlet, leave the wall switch ON. Control is via remote.

Cleaning and Maintenance

1. Remove the safety screw. Hold the lamp body with both hands, push up, and rotate counterclockwise to detach it.
2. Remove wiring caps, disconnect wires, and remove the safety steel rope.
3. Clean the fan net and blades as needed after disassembly.

Important Notes:

• Do not flush the lamp body directly with water. Dry thoroughly after cleaning. Ensure parts are correctly installed to prevent falling.
• Always switch off power before cleaning electrical parts. Wipe excess moisture with a sponge or cloth. Do not use flammable or toxic cleaning liquids.

Safety

Please confirm voltage compatibility before use. Inappropriate voltage may damage the product and cause potential safety hazards.

The light source is non-user replaceable and must be serviced by the manufacturer or a qualified person.

Do not touch fan blades during operation.

Minimum installation height: 2.3 meters.

The lamp can be controlled by remote or mobile phone software. Turning off the lamp via remote/app does not necessarily cut off power. Do not touch, replace, or disassemble the lamp in this state to avoid electric shock or injury.

Remote Control Pairing and Disconnection

Pairing the Remote

Connect power, confirm normal operation (light turns on slowly). Turn off power for 5-10 seconds, then turn back on. Long press the "FAN OFF" button until the device flashes 3 times quickly. Pairing is successful.

Disconnecting the Remote

To disconnect the remote from the fan/lamp (useful for controlling multiple fans with one remote): Connect power, confirm normal operation. Turn off power for 5-10 seconds, then turn back on. Long press the "TIMER" button until the device flashes 3 times quickly. The remote is cleared and needs re-pairing to control the device again.

Declaration of Conformity

FlinQ & Co B.V. declares that the FlinQ Lumifan (Models FQC8420 & FQC8421) complies with relevant European safety and hazardous substance restrictions, including directives 2014/53/EU, 2011/65/EU, and 2015/863/EU. The product has been tested according to harmonized standards. Full EU declaration of conformity is available at www.flinqproducts.nl.

Company Information:

Company: FlinQ & Co B.V.
Address: Eemweg 74, 3755LD Eemnes, The Netherlands

Product Name: FlinQ Lumifan
Product Rating: 85-265 V / 50/60 Hz
Product Type: Lights & Lighting > LED Ceiling Fans
Produced in: China