XBA-GEL6 Bill Acceptor
Option Switch Settings and Configuration
The XBA-GEL6 is a bill acceptor unit supporting various communication protocols including Pulse, MDB, ICT104U, and ICT104V. This document outlines its option switch settings and currency configuration.
Option Switch Settings (Pulse/MDB/ICT104U/ICT104V)
Supported bill denominations: Lari 5, 10, 20, 50, 100, 200 (6 bills).
| FUNCTION | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Reject Lari 5 & 10 | ON | |||||||
| Accept Lari 5 & 10 | OFF | |||||||
| Reject Lari 20 | ON | |||||||
| Accept Lari 20 | OFF | |||||||
| Reject Lari 50 | ON | |||||||
| Accept Lari 50 | OFF | |||||||
| Reject Lari 100 | ON | |||||||
| Accept Lari 100 | OFF | |||||||
| Reject Lari 200 | ON | |||||||
| Accept Lari 200 | OFF | |||||||
| Disable Bill Reject 4 Times, BA Stop By 30 Sec | ON | |||||||
| Enable Bill Reject 4 Times, BA Stop By 30 Sec | OFF | |||||||
| Stack Banknote when Power-up | ON | |||||||
| Reject Banknote when Power-up | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF |
DIP Switch Location
The DIP switch is located on the side of the XBA unit.
Visual representation shows the side profile of the XBA unit with a circular callout highlighting the DIP switch.
Currency Assign Data
| Interface | Bill value | Pulse | MDB | ICT104V | ICT104U |
|---|---|---|---|---|---|
| BV1 | Lari 5 | Lari 5 | Lari 5 | Lari 5 | Lari 5 |
| BV2 | Lari 10 | Lari 10 | Lari 10 | Lari 10 | Lari 10 |
| BV3 | Lari 20 | Lari 20 | Lari 20 | Lari 20 | Lari 20 |
| BV4 | Lari 50 | Lari 50 | Lari 50 | Lari 50 | Lari 50 |
| BV5 | Lari 100 | Lari 100 | Lari 100 | Lari 100 | Lari 100 |
| BV6 | Lari 200 | Lari 200 | Lari 200 | Lari 200 | Lari 200 |
Additional Configuration Settings
The following table details additional settings for the XBA-GEL6, covering various modes and pulse configurations.
| FUNCTION | SW1 | SW2 | SW3 | SW4 | SW5 | SW6 | SW7 | SW8 |
|---|---|---|---|---|---|---|---|---|
| Inhibit Active HIGH | ON | |||||||
| Inhibit Active LOW | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Pulse Mode Settings | ||||||||
| Credit-Pulse Normal HIGH | ON | |||||||
| Credit-Pulse Normal LOW | OFF | |||||||
| Other Mode | ON | |||||||
| Paste Store | OFF | |||||||
| Other Mode | ON | |||||||
| Reserved | OFF | |||||||
| Reserved | ON | |||||||
| Reserved | OFF | |||||||
| Protocol Mode Specifics | ||||||||
| MDB Mode: SF=100, DPP=2 | ON | ON | ||||||
| ICT104V Mode: Connect with coin changer | ON | |||||||
| Other Mode: Connect with ICT JPSTD converter board | ON | |||||||
| Pulse Configurations | ||||||||
| 1 pulse / Lari 5 | ||||||||
| MDB Mode | OFF | OFF | ||||||
| ICT104V Mode | OFF | OFF | ||||||
| Other Mode | OFF | OFF | ||||||
| 2 pulses / Lari 5 | ||||||||
| MDB Mode | OFF | ON | ||||||
| ICT104V Mode | OFF | ON | ||||||
| Other Mode | OFF | ON | ||||||
| 5 pulses / Lari 5 | ||||||||
| MDB Mode | ON | OFF | ||||||
| ICT104V Mode | ON | OFF | ||||||
| Other Mode | ON | OFF | ||||||
| 20 pulses / Lari 5 | ||||||||
| MDB Mode | ON | ON | ||||||
| ICT104V Mode | ON | ON | ||||||
| Other Mode | ON | ON |
CPU Board DIP Switch Location
The DIP switch is located on the CPU board. Access requires removing the CPU board cover first.
Visual representation shows the CPU board with an arrow pointing to the location of the DIP switch.
Configuration Notes
Manufacturer Setting
After setting the dip switches for credit pulses, the bill acceptor should be reset.
Notes:
- Please reset the bill acceptor after setting the dip switch.
- Dip switches 1 to 5 are used exclusively for pulse protocol.
- The unit does not feature a sleep function.
- A calibration card is required.
