Installation
SCENARIO 1: STUD
- Push vertical rail joiner (A) up into top vertical rail as shown, secure the vertical rail joiner (A) on hole B with panhead screw (#12 x 2 in.) (see Fig. 1).
- Put the lower vertical rail as shown and secure the lower vertical rail on the hole C and D with panhead screw (#12 x 2 in.) (see Fig. 2).
Figure Descriptions for Scenario 1:
- Fig. 1: Illustrates pushing the vertical rail joiner (A) into the top vertical rail and securing it with a screw into 'Hole B'. Two panhead screws are depicted.
- Fig. 2: Shows the lower vertical rail being attached to the upper rail using screws into 'Hole C' and 'Hole D'.
SCENARIO 2: CONCRETE
- Tear the drilling template box (H) according to the dashed line (see Fig. 3).
- Align the drilling template box (H) as a locator as shown and mark the holes on the wall (see Fig. 4).
- Drill 1/4 in. holes and insert wall anchors (1/4 in.) into hole B, C and D (see Fig. 5).
- Push vertical rail joiner (A) up into top vertical rail as shown, secure the vertical rail joiner (A) on hole B with panhead screw (#12 x 2 in.) (see Fig. 6).
- Put the lower vertical rail as shown and secure it on the hole C and D with panhead screw (#12 x 2 in.) (see Fig. 7).
Figure Descriptions for Scenario 2:
- Fig. 3: Depicts tearing the drilling template box (H) along its dashed lines.
- Fig. 4: Shows the template (H) positioned against a wall, with marks being made for drilling. 'Hole B', 'Hole C', and 'Hole D' are indicated.
- Fig. 5: Illustrates wall anchors being inserted into the wall at the marked locations for 'Hole B', 'Hole C', and 'Hole D'.
- Fig. 6: Similar to Fig. 1, showing the joiner (A) attached to the top rail at 'Hole B' with a screw.
- Fig. 7: Similar to Fig. 2, showing the lower rail attached to the upper rail with screws at 'Hole C' and 'Hole D'.
SCENARIO 3: DRYWALL
- Tear the drilling template box (H) according to the dashed line (see Fig. 8).
- Align the drilling template box (H) as a locator as shown and mark the holes on the wall (see Fig. 9).
- Drill 1/4 in. holes for hole B and C, drill 1/2 in. hole for hole D. Insert wall anchors (1/4 in.) into hole B and C (see Fig. 10).
- Push vertical rail joiner (A) up into top vertical rail as shown, secure the vertical rail joiner (A) on hole B with panhead screw (#12 x 2 in.) (see Fig. 11).
- Put the lower vertical rail as shown and secure it on hole C with panhead screw (#12 x 2 in.) and on hole D with toggle (3/16 in.) and bolt (3 in.) (see Fig. 12). Make sure the toggle (3/16 in.) and the bolt (3 in.) are installed on lower vertical rail before secure.
Figure Descriptions for Scenario 3:
- Fig. 8: Shows tearing the drilling template box (H) along dashed lines.
- Fig. 9: Depicts the template (H) aligned on the wall, with marks made for holes. 'Hole B', 'Hole C', and 'Hole D' are indicated.
- Fig. 10: Illustrates drilling holes for anchors. 'Hole B' and 'C' are drilled for 1/4 in. anchors, and 'Hole D' is drilled for a 1/2 in. hole. Wall anchors are shown for B and C.
- Fig. 11: Similar to Fig. 1 and 6, showing the joiner (A) secured to the top rail at 'Hole B' with a screw.
- Fig. 12: Shows the lower rail attached to the upper rail. 'Hole C' uses a panhead screw, and 'Hole D' uses a toggle and bolt.
Warranty
This product is guaranteed to be free of defects in materials and workmanship for 2 years from the date of purchase. If this product is defective, call 1-800-305-1726 or return the product to the store from which it was purchased for a replacement. Guarantee does not include normal wear and tear.
Assistance & Warnings
For further assistance:
HOMEDEPOT.com | Please contact 1-800-305-1726
⚠ WARNING: This product can expose you to chemicals, including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
