Fortin EVO ONE Regular Installation Guide

Product Overview and Vehicle Compatibility

This document provides the regular installation guide for the Fortin EVO ONE module, an all-in-one remote starter, alarm, immobilizer bypass, and data interface module.

Vehicle Compatibility: NISSAN Sentra equipped with Push-to-Start ignition, model years 2013-2019.

Module Information:

• Bypass Firmware Version: 72.[48]
• To add firmware version and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).

Programmable Options

Remote Starter Option: Program remote starter functionality.

R.S. OEM REMOTE STAND ALONE Option: Program for OEM remote stand-alone start.

Bypass Options:

• C1: OEM Remote status (Lock/Unlock) monitoring.
• D6: Push-to-Start functionality.
• A11: Hood trigger (Output Status).

Important Notes

The vehicle's OEM remote and SmartKey remain operable during remote start.

Mandatory Installation Requirements

Hood Pin Contact: The hood pin switch (included) must be installed if the vehicle can be remote started with the hood open. If the hood pin is not functional or not installed, set Function A11 to OFF (❌).

Security Sticker: The security sticker (included ✔️) is a mandatory safety element and must be installed.

WARNING: This module must be installed by a qualified technician. Incorrect connections can cause permanent damage to the vehicle.

Component Identification and Wiring Locations

Key locations for wiring connections include:

• BCM (Body Control Module)
• Driver kick panel
• Immobilizer connector
• OBDII connector
• Brake switch
• Push-to-Start button

Key connection points identified:

• (+)PARKING LIGHTS
• (-)DOOR PIN
• (-)LOCK ?
• (-)UNLOCK ?
• (+)IGNITION
• (~)RX
• (~)TX
• (-)PTS (Push-to-Start)
• (+)12V
• (+)BRAKE
• CAN HIGH
• CAN LOW

Automatic Transmission Wiring Connection

This section details the wiring for automatic transmission vehicles. Note the instruction to CUT LOOP FOR AUTOMATIC TRANSMISSION MODE.

Main Harness (EVO ONE Module):

• A1: (+)Ignition (Yellow wire)
• A2: (-)Lock (Purple wire)
• A3: (-)Unlock (Purple/White wire)
• A4: (Green wire)
• A5: (White wire)
• A6: (-)Disarm (Orange wire)
• A7: (Orange/Black wire)
• A8: (-)Door Pin (Dk.Blue wire)
• A9: (Red/Blue wire)
• A10: (~)TX (Lt.Blue/Black wire)
• A11: Black wire (Connects to Black 40-Pin BCM connector)
• A12: Pink wire
• A13: Yellow/Black wire
• A14: Brown/White wire
• A15: (-)Hood pin (Pink/Black wire)
• A16: (~)TX (Purple/Yellow wire)
• A17: (~)RX (Green/White wire)
• A18: (Green/Red wire)
• A19: (-)PTS (White/Black wire)
• A20: (~)RX (Lt.Blue wire)

Other Connections:

• E1: (+)Parking lights (White wire)
• E2: (+)12V (Orange wire)
• E3: (+)12V (Red wire)
• E4: (-)Ground (Black wire)
• E5: (Pink wire)
• E6: (Yellow wire)

CAN Bus Connections:

• C1: (Orange/Green wire)
• C2: (Orange/Brown wire)
• C3: CAN HIGH (Gray wire)
• C4: CAN LOW (Gray/Black wire)
• C5: (Brown wire)
• D1: (~)TX (Yellow/Green wire)
• D2: (Yellow/Blue wire)
• D3: (Yellow/Red wire)
• D4: (White/Green wire)
• D5: (White/Blue wire)
• D6: (+)Brake (White/Red wire)

Fuses: 15 AMP FUSE included.

CAUTION: An incorrect connection may cause permanent damage to the module.

Manual Transmission Wiring Connection

This section details the wiring for manual transmission vehicles. Key connections include:

• (+)Ignition (Yellow wire)
• (-)Lock (Purple wire)
• (-)Unlock (Purple/White wire)
• (-)Driver door Pin (Dk.Blue wire)
• (~)TX (Lt.Blue/Black wire)
• (-)Hood pin (Pink/Black wire)
• (~)RX (Lt.Blue wire)
• (+)Parking lights (White wire)
• (+)12V (Orange wire)
• (-)Ground (Black wire)
• (+)Brake (Pink wire)
• (+) CLUTCH1, (+) CLUTCH2
• CAN HIGH, CAN LOW

Fuses: 15 AMP FUSE included.

CAUTION: An incorrect connection may cause permanent damage to the module.

Key Bypass Programming Procedure (Part 1/2)

1. Preparation: Remove the valet key from the back of the OEM remote. Remove the battery from the OEM remote. Keep other OEM remotes at least 3 meters (10 feet) away from the vehicle.
2. Initial Connection: Press and hold the programming button. Connect the 6-PIN Main harness (White connector). Observe LEDs: Blue, Red, Yellow, and Blue & Red will illuminate alternatively. Release the programming button when the LED is YELLOW.
3. Connector Insertion: Insert the required remaining connectors.
4. Programming Button Press: Press and release the programming button three (3x) times. The YELLOW LED will flash 3 times each second. Wait for the YELLOW LED to turn ON solid.
5. Remote Placement: Place the OEM remote (no battery) close to the front of the START/STOP button, as shown. The transponder is located behind the logo.
6. Vehicle Type Specific Steps:
   • Automatic Transmission: Press and release the foot-brake pedal. The RED LED turns ON, and the YELLOW LED turns OFF. Press the START/STOP button twice to turn ON the ignition. Press the START/STOP button once to turn OFF the ignition. Wait until the "press brake" message disappears (may take up to 12 seconds).
   • Manual Transmission: Follow specific steps involving brake pedal and START/STOP button presses, observing LED indicators.

Key Bypass Programming Procedure (Part 2/2)

7. Remote Interaction: Hold the OEM remote close to the front of the START/STOP button. Press and release the foot-brake pedal. The RED LED is ON, and the BLUE LED turns ON. Press the START/STOP button twice to turn ON the ignition. Press the START/STOP button once to turn OFF the ignition.
8. Ignition ON: Press the START/STOP button twice to turn ON the ignition. The BLUE LED will flash rapidly. The RED LED turns OFF.
9. Ignition OFF: Press the START/STOP button once to turn OFF the ignition. Wait until the BLUE LED flashes slowly.
10. Disconnection: Disconnect all connectors, including the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
11. Software Programming: Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool with a computer (Microsoft Windows, Internet connection required) or smartphone to visit the DCryptor menu.
12. Reconnection: AFTER DCRYPTOR PROGRAMMING IS COMPLETED, reconnect the 6-Pin (Main-Harness) or 4-pins (Data-Link) connector, and then all remaining connectors.

The module is now programmed.

Verification: Test the remote starter by starting the vehicle remotely.

Remote Starter Functionality

Starting the Vehicle:

• Ensure all doors are closed.
• Use the remote to start the vehicle.

Unlocking Doors: Unlock the doors using either the OEM remote, the remote-starter remote, or the proximity remote.

Entering the Vehicle: Enter the vehicle with the Intelligent Key.

Driving: The vehicle is now ready to be put into gear and driven.

Note: If the vehicle is not unlocked with one of these conditions, the remote-starter will shut down as soon as any door is opened.

Notices and Warnings

Updated Guides: Updated firmware and installation guides are posted on the Fortin website (www.fortin.ca). It is recommended to update the module to the latest firmware and download the latest installation guide(s) prior to installation.

General Warning: The information in this guide is provided "as is" without warranty of accuracy. The installer is solely responsible for verifying all circuits before connecting. Only a computer-safe logic probe or digital multimeter should be used. Fortin Electronic Systems assumes no liability for the accuracy or installation. This module must be installed by a qualified technician. This guide is a suggestion and may change without notice. Visit www.fortinbypass.com for the latest version.

Technical Support and Contact Information

Tech Support:

• Phone: 514-255-HELP (4357) / 1-877-336-7797

Website: www.fortinbypass.com