OttLite LED Desk Space Organizer Lamp & Book Light: User Manual and Instructions
Congratulations!
You've purchased the finest in natural lighting technology with your new OttLite® product.
Product Registration
Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty
LED Desk Space Organizer Lamp Setup and Operation
Note: This Unit is Fully Assembled
1. Remove the lamp from packing, placing the lamp body base (labeled A) flat on a steady surface.
2. Connect the AC Adapter input (labeled E) into connector (labeled F) in the rear-bottom of the lamp.
3. Plug the AC adapter (labeled H) into a standard household 120V AC outlet. Note: Only use with the supplied AC adapter to avoid damage or fire.
Operation
4. Turn the lamp ON & OFF using the power switch (labeled B) located in the front side of base (A) near the storage area. The power switch (B) is a "touch" switch that controls the dimmer function for 4 levels of brightness.
5. To cycle through LED brightness settings, lightly touch the switch:
- For 1st brightness setting (ON): touch the switch once.
- For 2nd brightness setting: touch the switch twice.
- For 3rd brightness setting: touch the switch three times.
- For 4th brightness setting: touch the switch four times.
- To turn lamp OFF: touch the switch five times.
Positioning the Light
6. To position the lamp shade, simply bend the flex-neck (labeled G) as needed to point the light. Please hold the lamp base (labeled A) while adjusting the lamp. Take care not to overextend the lamp to avoid unbalancing it and causing damage.
Enjoy your OttLite® LED Desk Space Organizer Lamp!
Safety Warnings
To reduce the risk of fire, electric shock, or injury to persons:
- Turn the lamp off and wait until the lamp head (labeled C) and adapter (labeled H) are cool before handling.
- The LED panel (labeled D) might get hot after several hours of continuous use. Do not place your hands directly on the LED light panel.
- Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
- Do not alter the plug.
- The lamp head included with this unit cannot be replaced by the consumer.
- Note: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
Caution
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
Any change or modification to the product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of the product.
FCC Part 15 Compliance
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-3 (B) / NMB-3 (B)
AC/DC Adapter and USB Port
AC/DC Adapter:
- Input: AC 100-240V, 50/60 Hz, 0.5A MAX
- Output: 13V DC, 1.2A with a Male DC Plug
This lamp contains a 5V-2.1A USB output port (labeled J) located on the base of the lamp. The USB port can charge items such as tablets, cellular phones, etc.
LED Book Light Setup and Operation
Note: This Unit is Fully Assembled
1. Remove the book light and accessory from packing and place them on a flat steady surface (e.g., a table).
2. The OttLite LED Book Light is powered by 3 AAA batteries (not included). Alkaline or rechargeable batteries are recommended.
3. Install batteries per the BATTERY INSTALLATION procedure.
4. This LED Book Light can be mounted on a book edge or placed on a flat surface such as a table.
5. A USB cord (labeled H) is included with the LED Book Light.
6. To use the USB cord (H): Connect input (labeled G) to the LED Book Light connection port (labeled F). Connect the USB input (labeled J) to a USB power source (refer to Figure 1).
Note: This product does not contain a charging mechanism; therefore, the USB cord is provided solely as a power source connection to a USB port such as a computer. During battery operation, DO NOT attach the USB to the item as it will cut off DC battery power.
Mounting Options
Clip Mount
1. To mount or attach the LED Book Light, open the clip (labeled B) and insert the Book Light body (labeled A) fully onto an appropriate edge, verifying the body is held firmly onto the book (reference Figure 3).
2. An appropriate edge will be thicker than 0.6 cm (1/4 inch) and less than 2.5 cm (1 inch).
3. To position the LED light source (labeled D), simply bend the stem or flex-neck (labeled C) as needed to point the light. Please hold the body (labeled A) while adjusting the flex-neck (labeled C).
4. Turn the LED light ON & OFF using the power switch (labeled E) located on the front-upper side of the LED Light Source (labeled D).
Table Use
1. Set the Book Light body (labeled A) on a steady flat surface such as a table (reference Figure 4).
2. To position the LED light source (labeled D), simply bend the flex-neck (labeled C) as needed to point the light. Please hold the body (labeled A) while adjusting the flex-neck (labeled C).
3. Turn the LED light ON & OFF using the power switch (labeled E) located on the front-upper side of the LED Light Source (labeled D).
DO NOT FORCE the flexible stem into any extreme positions as damage may occur.
Battery Installation
1. Your OttLite LED Book Light is powered by 3 AAA batteries (not included). With standard alkaline batteries, the LED Book Light will operate approximately 72 hours. Light output will slowly diminish as the batteries lose energy.
Warning: Keep away from children. If swallowed, promptly see a doctor. Do not install backwards, charge, put in fire, or mix with other battery types – may explode or leak causing injury.
2. To install batteries, slide the battery compartment door (labeled K) away from the stem while slightly depressing the door near the tab (reference Figure 2).
3. Install the 3 batteries as indicated by the graphic inside the battery compartment. Battery negative terminals should point toward the spring.
4. Replace the battery compartment door (labeled K) by laying it on the open compartment and sliding the door toward the stem to engage the tabs to the compartment; a click should be heard as it locks into place.
Notice: Only replace batteries as a simultaneous set and do not mix with older batteries. Remove batteries if consumed or if the light has not been in use for a long period of time.
General Safety Note
Note: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
Caution
Any change or modification to the product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of the product.
FCC Part 15 Compliance (Book Light)
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAN ICES-3 (B) / NMB-3 (B)
Accessories: USB Cord
