OttLite LED Desk Lamp with Color Changing Tunnel

Congratulations!

You've purchased the finest in natural lighting technology with your new OttLite® product.

Product Registration

Please complete the enclosed Product Registration Form and return it today by mail, or register online by going to: OttLite.com/warranty

Getting Started

Note: This unit is fully assembled.

1. Remove the lamp from its packaging and place the lamp body base (A) flat on a steady surface.
2. Connect the AC adapter input (J) into the connector (K) in the rear-bottom of the lamp.
3. Plug the AC adapter (L) into a standard household 120V AC outlet. Note: Only use with the supplied AC adapter to avoid damage or fire.
4. Turn the lamp ON & OFF by using the power switch [power-symbol] (C) located on the lamp's control panel (B).
5. The lamp control panel (B) includes multiple "touch" keys that control the lamp's light color and brightness settings, as well as a color changing tunnel. This lamp provides three color modes and five levels of brightness. Refer to the "Touch Key Panel Instructions" section for operating details.
6. To position the shade, simply bend the flex-neck (O) as needed to point the light. Please hold the lamp base (A) while adjusting the lamp. Take care not to overextend the lamp to avoid unbalancing it and causing damage. Refer to diagrams for the lamp's maximum adjustment range.

Touch Key Panel Instructions

To operate LED color & brightness settings, lightly touch the required "key" to achieve the following:

• Turn lamp "ON/OFF": Touch the power key [power-symbol] (C).
• To adjust lighting color mode: Touch the "M" key [mode-key] (D) to switch light color temperature modes: 5000°K, 2700°K, 4000°K. Note: 5000°K is the default color mode.
• There are five preset brightness levels. To adjust brightness: touch the up arrow [brightness-up] (E) to increase brightness and the down arrow [brightness-down] (F) to lower brightness.

LED Color Changing Tunnel Instructions

The Color Changing Tunnel can be turned ON & OFF by touching the power switch [tunnel-power-switch] (G) located to the left of the light changing bar [color-bar] (H).

Turn the light changing bar to "ON" status. To engage the function for different colors, do one of the following:

• Touch the desired color represented within the light changing bar [color-bar] (H).
• Slide your finger along the light changing bar [color-bar] (H) in either direction.
• Touch the light changing bar power switch [tunnel-power-switch] (G) for "three seconds" and watch the light color change automatically.

Safety Warnings

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:

1. Turn the lamp OFF and WAIT UNTIL THE LAMP HEAD (M) AND ADAPTER (L) ARE COOL before handling.
2. The LED panel (N) might get hot after several hours of continuous use. DO NOT place your hands directly on the LED light panel.
3. Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by the consumer.

Note: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.

CAUTION! If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.

Regulatory Information

FCC Part 15

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3 (B)/NMB-3 (B)

OttLite Technologies Caution

Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of product.

Specifications

AC/DC ADAPTER

• Input: AC 100-240V, 50/60 Hz, 0.8A
• Output: 12V DC, 1.5A with a Male DC Plug

USB Port: This lamp contains a 5V-2.1A USB output port (P) located on the base of the lamp. The USB port can charge such items as tablets, cellular phones, etc.

Diagram Descriptions

The lamp features a flexible neck (O) allowing for adjustable positioning of the light head (M). The base (A) houses the control panel (B) with touch-sensitive keys for power [power-symbol] (C), mode selection [mode-key] (D), brightness adjustment [brightness-up] (E) and [brightness-down] (F), and the color changing tunnel controls [tunnel-power-switch] (G) and [color-bar] (H). The LED panel (N) is located in the lamp head. The AC adapter (L) connects via input (J) to connector (K). A USB output port (P) is located on the base.

The lamp's flexible neck allows for a wide range of motion, with diagrams indicating typical adjustment angles such as 30°, 45°, and 90° to direct the light effectively.