Nitho Raven Gaming Chair
Quick Start Guide
Model: GC-RAVN
⚠️ IMPORTANT INFORMATION
READ CAREFULLY. KEEP THIS INFORMATION FOR FURTHER REFERENCE.
GENERAL GUIDELINES
- Please read the following instructions carefully and use the product accordingly.
- Please keep this manual and hand it over when you transfer the product.
- This summary may not include every detail of all variations and considered steps.
- Please contact support@nitho.com when further information and help are needed.
NOTES
- Please follow the assembly instructions precisely and only use the product as intended.
- If an odor is present when first opening the package, please leave the unwrapped product in a shaded and ventilated area for a few days to air out.
- Prior to assembly, please check the product for defects or missing accessories. If any defects are found or accessories are missing, do not use the product as damage or injury may occur.
- Please contact NITHO for assistance and replacement.
- During assembly, please only slightly tighten all screws in their correct position first, then fully tighten them. A Philips screwdriver is recommended but not included.
- It is suggested you regularly check the product's bolts and connections to ensure safe use.
- Assemble the item on a soft, flat, and clean surface to avoid scratches and damage.
WARNINGS
- During assembly, keep parts and packaging materials away from children and pets as they could cause injury and are a potential choking hazard.
- Avoid sharp objects or corrosive chemicals to prevent damage to the product.
- Please open the item slowly and cautiously to avoid pinching your hands by metal joints, especially children.
Components
Please check you have all the pieces listed below:
| Component | Description | Quantity |
|---|---|---|
| A | Casters (Wheels) | x 5 |
| B | Chair Base | x 1 |
| C | Gas Lift Cylinder | x 1 |
| D | Gas Lift Cylinder Cover | x 1 |
| E | Mechanism | x 1 |
| F | Screw (M6*20mm) | x 4 |
| G | Screw (M6*40mm) | x 3 |
| H1 | Headrest Pillow | x 1 |
| H2 | Lumbar Pillow | x 1 |
| I | Washer | x 3 |
| J | Screw (M8*40mm) | x 4 |
| K | Allen Wrench | x 1 |
| L | Backrest Mounting Bracket | x 1 |
| M | Armrests (Left & Right) | x 1 (pair) |
| N | Seat Plate | x 1 |
| O | Seat Cushion | x 1 |
| P | Washer | x 4 |
| Q | Backrest | x 1 |
| R | Additional Seat Cushion | x 1 |
| X | Armrest Brackets | x 2 |
| T | Screw (M6*30mm) | x 6 |
| U | Screw (M5*8) | x 1 |
Assembly Instructions
Step 1: Base Assembly
Description: Insert five casters (A) into the chair base (B). Place the gas lift cylinder cover (D) over the gas lift cylinder (C) and insert the cylinder (C) into the center of the chair base (B).
Visual Aid: Diagram shows the chair base with wheels inserted, followed by the gas lift cylinder and its cover.
Step 2: Seat Plate Attachment
Description: Align the backrest mounting bracket (L) with the designated holes on the underside of the seat cushion (O). Secure it using screws (G) and the Allen wrench (K). Attach the seat plate (N) to the seat cushion assembly.
Visual Aid: Diagram shows the underside of the seat cushion with the bracket being attached using screws and an Allen wrench. The seat plate is also shown.
Step 3: Mechanism Attachment
Description: Attach the mechanism (E) to the underside of the seat cushion (O) using screws (F) and the Allen wrench (K).
Visual Aid: Diagram shows the mechanism being screwed onto the seat cushion.
Step 4: Backrest Attachment
Description: Position the backrest (Q) against the seat cushion assembly. Use the armrest brackets (X) to connect the backrest to the seat cushion. Secure using screws (T), washers (U), and the Allen wrench (K).
Visual Aid: Diagram shows the backrest being attached to the seat cushion using brackets, screws, washers, and an Allen wrench.
Step 5: Connecting Seat to Base
Description: Carefully lift the assembled seat cushion and mechanism and align it with the gas lift cylinder (C) on the chair base. Lower the seat assembly onto the cylinder.
Visual Aid: Diagram shows the seat assembly being placed onto the gas lift cylinder.
Step 6: Detail of Seat Connection
Description: This step provides a closer view of how the seat assembly connects securely to the gas lift cylinder.
Visual Aid: Close-up diagram illustrating the connection point.
Step 7: Armrest and Seat Plate Connection
Description: Attach the left and right armrests (M) to the sides of the seat plate (N) and mechanism (E) using screws (J) and washers (P) with the Allen wrench (K). Also, attach the backrest (Q) to the seat plate (N) using screws (P) and washers (J) with the Allen wrench (K).
Visual Aid: Diagram shows armrests being attached to the seat and mechanism, and the backrest being attached to the seat plate.
Step 8: Pillow Attachment
Description: Attach the headrest pillow (H1) and the lumbar pillow (H2) to the backrest (N) using the integrated straps.
Visual Aid: Diagram shows the pillows being attached to the backrest.
Step 9: Final Assembly
Description: The chair is now fully assembled and ready for use.
Visual Aid: Front view of the completed Nitho Raven Gaming Chair.
Service & Support
For any questions or support needs, please contact the NITHO Team at support@nitho.com or visit our website at www.nitho.com.
Company Information:
NITHO GmbH
Victoriastrasse 3b
86150 Augsburg - Germany
Follow us:
Email: SUPPORT@NITHO.COM | Website: WWW.NITHO.COM | Instagram: NITHOGAMES | Facebook: NITHOGAMES
