NITHO MC.I Mesh Chairs

Important Information

⚠ IMPORTANT INFORMATION
READ CAREFULLY. KEEP THIS INFORMATION FOR FURTHER REFERENCE.

General Guidelines

• Please read the following instruction carefully and use the product accordingly.
• Please keep this manual and hand it over when you transfer the product.
• This summary may not include every detail of all variations and considered steps. Please contact NITHO for further information and help when needed.

Notes

• Please follow the assembly instructions precisely and only use the product as intended.
• If an odor is present when first opening the package, please leave the unwrapped product in a shaded and ventilated area for a few days to air out.
• Prior to assembly, please check the product for defects or missing accessories. If any defects are found or accessories are missing, do not use the product as damage or injury may occur. Please contact NITHO for assistance and replacement.
• During assembly, please only slightly tighten all screws in their correct position first, then fully tighten them. A Philips screwdriver is recommended but not included.
• It is suggested you regularly check the products bolts and connections to ensure safe use.
• Assemble the item on a flat and clean surface to avoid scratches and damage.

Warnings

• During assembly, keep parts and packaging materials away from children and pets as there could cause injury and are a potential choking hazard.
• Avoid sharp objects or corrosive chemicals to prevent damage to the product.
• Please open the item slowly and cautiously to avoid pinching your hands by metal joints, especially children.

Components

Please check you have all the pieces listed below:

• A: Casters (5)
• B: Chair Base (1)
• C: Gas Lift Cylinder (1)
• D: Seat Cushion (1)
• E: Backrest (1)
• F: Mechanism/Control Unit (1)
• G: Armrests (2)
• I: Armrest Supports/Brackets (2)
• J: M6*20 Screws (2)
• K: M6*14 Screws (4) and M6*20 Screws (10)
• L: M6*35 Screws (8)
• M: Allen Key (1)
• N: Headrest (1)
• O: Headrest Attachment Post/Bolt (1)
• P: Allen Key (1)

Assembly Instructions

Step 1: Base Assembly

Insert the five casters (A) into the holes at the end of the chair base (B). Then, insert the gas lift cylinder (C) into the central opening of the chair base (B).

Step 2: Attach Armrests to Seat

Position the armrests (G) onto the underside of the seat cushion (D). Secure each armrest using two M6*14 screws (K), for a total of four screws, with the provided Allen key (P).

Step 3: Attach Backrest to Seat

Align the backrest (E) with the rear of the seat cushion assembly (D). Attach the backrest using four M6*35 screws (L) and the Allen key (P).

Step 4: Attach Armrest Supports

Attach the armrest supports/brackets (I) to the underside of the seat cushion assembly (D) using four M6*35 screws (L) and the Allen key (P).

Step 5: Attach Mechanism to Seat

Place the mechanism/control unit (F) onto the underside of the seat cushion assembly (D). Secure it using four M6*20 screws (K) and the Allen key (P).

Step 6: Attach Mechanism to Backrest

Attach the mechanism/control unit (F) to the backrest (E) using two M6*20 screws (J) and the Allen key (P).

Step 7: Attach Headrest

Attach the headrest (N) to the top of the backrest (E). Insert the provided part (O) and secure with two M6*20 screws (K) using the Allen key (P).

Step 8: Final Assembly

Place the assembled chair onto the gas lift cylinder (C) on the chair base (B).

Service & Support

If you have any questions or require support, contact the NITHO Team at support@nitho.com or visit the website www.nitho.com.

NITHO GmbH - Victoriastrasse 3b - 86150 Augsburg - Germany

Email: SUPPORT@NITHO.COM | Website: WWW.NITHO.COM | Social: NITHOGAMES