Important Information
⚠️ IMPORTANT INFORMATION
READ CAREFULLY.
KEEP THIS INFORMATION FOR FURTHER REFERENCE.
General Guidelines
- Please read the following instructions carefully and use the product accordingly.
- Please keep this manual and hand it over when you transfer the product.
- This summary may not include every detail of all variations and considered steps.
- For further information and help, contact NiTHO GmbH at support@nitho.com or visit www.nitho.com.
Notes
- Please follow the assembly instructions precisely and only use the product as intended.
- If an odor is present when first opening the package, please leave the unwrapped product in a shaded and ventilated area for a few days to air out.
- Prior to assembly, please check the product for defects or missing accessories. If any defects are found or accessories are missing, do not use the product as damage or injury may occur.
- Please contact NiTHO GmbH for assistance and replacement.
- During assembly, please only slightly tighten all screws in their correct position first, then fully tighten them. A Philips screwdriver is recommended but not included.
- It is suggested you regularly check the product's bolts and connections to ensure safe use.
- Assemble the item on a soft, flat, and clean surface to avoid scratches and damage.
Warnings
- During assembly, keep parts and packaging materials away from children and pets, as they could cause injury and are a potential choking hazard.
- Avoid sharp objects or corrosive chemicals to prevent damage to the product.
- Please open the item slowly and cautiously to avoid pinching your hands by metal joints, especially children.
Components
Please check you have all the pieces listed below:
| Part | Description | Quantity |
|---|---|---|
| A | Chair base with 5 casters | x 1 |
| B | Casters | x 5 |
| C | Gas lift cylinder | x 1 |
| D | Headrest | x 1 |
| E | Backrest | x 1 |
| F | Seat cushion | x 1 |
| G | Armrests | x 2 |
| H | Armrest brackets | x 2 |
| I | Mechanism/control unit | x 2 |
| J | Seat plate | x 2 |
| K | Lumbar support bracket | x 2 |
| L | Lumbar support adjustment mechanism | x 2 |
| M | Screws (M4x14mm) | x 2 |
| N | Screws (M6x14mm) | x 2 |
| O | Screws (M6x20mm) | x 4 |
| P | Screws (M6x25mm) | x 4 |
| Q | Screws (M6x35mm) | x 7 |
| R | Screws (M8x25mm) | x 2 |
| S | Screw covers/caps | x 4 |
| T | Allen key | x 1 |
Assembly Instructions
- Step 1: Insert the casters (B) into the openings on the chair base (A). Then, insert the gas lift cylinder (C) into the central hole of the chair base (A).
- Step 2: Attach the armrest brackets (H) to the underside of the seat cushion (F) using four screws (Q).
- Step 3: Attach the seat plate (J) to the underside of the seat cushion (F) using four screws (O).
- Step 4: Attach the mechanism/control unit (I) to the seat plate (J) using two screws (N).
- Step 5: Carefully place the assembled seat unit onto the gas lift cylinder (C).
- Step 6: Attach the lumbar support bracket (K) to the backrest (E) using three screws (Q).
- Step 7: Attach the backrest assembly (E with K) to the seat mechanism (J) using screws (P).
- Step 8: Attach the headrest (D) to the top of the backrest (E) using two screws (P). Attach the lumbar support adjustment mechanisms (L) to the backrest (E) using two screws (M).
- Step 9: Attach the armrests (G) to the sides of the seat cushion (F) and backrest (E) using two screws (R) per armrest. Secure the armrest brackets (H) with screw covers (S).
- Step 10: Ensure all screws are fully tightened and the chair is stable. Your NiTHO MC.II Mesh Chair is now assembled.
Service & Support
For any questions or support requirements, please contact the NiTHO Team at support@nitho.com or visit the website www.nitho.com.
NITHO GmbH
Victoriastrasse 3b - 86150 Augsburg - Germany
Follow us on social media:
