Hansgrohe Zesis M33 Series Faucets

General Information and Safety Instructions

This guide provides instructions for the installation and use of Hansgrohe Zesis M33 series faucets. Please read all instructions carefully before proceeding.

Safety Instructions:

• Wear gloves during installation to prevent cuts and bruises.
• Ensure pressure differences between hot and cold water connections are equalized.
• Check the product for shipping damage before installation. No responsibility will be accepted for shipping or surface damage after installation.
• Pipes and faucet must be installed, flushed, and checked according to valid standards and country-specific installation guidelines.
• Model 74811000: This faucet cannot be used with an instantaneous water heater.
• Models 74807000, 74808000: Only connect washing machines or dishwashers with DVGW marking to the appliance connection valve without additional safety devices. If no appliance is connected, the appliance connection valve must be plugged.
• Do not use silicone containing acetic acid.
• The product is designed for potable water only.

Technical Data

Usage and Maintenance

• Water temperature from faucets should not exceed 65°C for consumption. The faucet must not impair the quality of water intended for human consumption (e.g., for drinking and cooking).
• After commissioning and periods of non-use, strictly follow the instructions. Flush the faucet for at least 2 minutes with cold and hot water. After a minimum of 1 day of non-use, do not consume the stagnant cold or hot water in the faucet; drain it first by running water for at least 2 minutes. The drained water must not be used for drinking or food preparation.
• Due to hot water's greater metal-dissolving capacity, cold water is recommended for cooking and drinking.
• It is recommended to descale and disinfect the faucet aerator monthly. Use only cleaning agents that comply with relevant regulations for cleaning and disinfection.
• The aerator creates significant aerosols, posing a Legionella exposure risk. Therefore, its use is not recommended in hospital patient rooms or any location where Legionella counts in cold and/or hot water reach the intervention level defined by the relevant EMMI decree.

Troubleshooting

Assembly Instructions

Step 1: Hose Installation

Step 1a: Insert the flexible hoses into the mounting hole, ensuring the maximum insertion depth is 35 mm.

Step 1b: Insert the flexible hoses into the mounting hole, ensuring the maximum insertion depth is 60 mm.

Step 2: Securing the Faucet Body

Mount the faucet body onto the sink or countertop. Secure using the provided fitting, tightening to 3 Nm (Newton-meters).

Step 3: Connecting Water Supply

Connect the flexible hoses to the water supply points.

Step 4: Connecting Supply Lines

Connect the hot and cold water supply lines to the faucet body. Use a 9 mm wrench (SW 9 mm) for one connection and a 19 mm wrench (SW 19 mm) for the other, tightening to 4 Nm.

Step 5: Final Faucet Installation

Step 5a: Install the faucet onto the sink or countertop for models 74802XXX, 74805000, 74808000, 74811000, 74815XXX. The diagram shows the faucet body being secured from below.

Step 5b: Install the faucet onto the sink or countertop for models 74807000, 74813000. The diagram shows the faucet body being secured from below.

Step 6: Aerator Removal

Remove the aerator using a 22 mm wrench (SW 22 mm).

Step 7: Handle Removal

Remove the faucet handle by pulling it upwards.

Step 8: Cartridge Removal

Remove the cartridge using a 22 mm wrench (SW 22 mm), tightening to 2 Nm.

Step 9: Connecting Hoses to Faucet Body

Connect the flexible hoses to the faucet body using 12 mm and 24 mm wrenches (SW 12 mm, SW 24 mm).

Step A-E: Handle and Cartridge Assembly

Step A: Attach the handle. Loosen the fixing screw (SW 2.5 mm), slide the handle onto the cartridge, and tighten the screw. The handle can be positioned at 60° or 110° angles.

Step B: Insert the cartridge into the faucet body.

Step C: Shows the possible angles for the handle: 60° and 110°.

Step D: Insert the cartridge into the faucet body.

Step E: Attach the handle. Loosen the fixing screw (SW 2.5 mm, 3.5 Nm), slide the handle onto the cartridge, and tighten the screw (SW 30 mm, 12 Nm).

Step 1-6: Temperature Limiter Adjustment

Step 1: Secure the handle using a 2.5 mm wrench (SW 2.5 mm), repeating the action four times.

Step 2: Shows water temperature indicators: 10°C (cold), 60°C (hot), and pressure indicators (0.3 MPa).

Step 3: Use pliers to remove a component.

Step 4: Shows temperature settings: 36°C, 38°C, 43°C, 50°C, 55°C, 60°C, indicating adjustment points.

Step 5: Shows assembly of a component.

Step 6: Attach the handle. Secure with a 2.5 mm wrench (SW 2.5 mm, 3.5 Nm).

Step 1-4: Specific Model Installation (Zesis M33 160 1jet 74805000)

Step 1: Lift the faucet body.

Step 2: Install the faucet onto the sink or countertop, ensuring a minimum clearance of 55 mm.

Step 3: Clean the installation area.

Step 4: Secure the faucet body from below (Step 1) and attach the handle (Step 2). Apply faucet grease (Armaturenfett / Grease / 润滑油) to the relevant parts.

Parts Lists (Exploded Views)

The following lists provide part numbers for various Zesis M33 models as shown in the exploded diagrams:

Zesis M33 150 1jet (74802XXX)

93735610, 98446000, 94390XXX, 94388XXX, 94389000, 98212000 (41x2), 93895000, 95008000, 13913000, 98750000, 98186000 (30x2), 98702000, 98212000 (41x2), 98190000 (36x2,5), 97523000, 97548000, 95049000, 96510000.

Zesis M34 150 1jet (74815XXX)

93735610, 98446000, 94392XXX, 94388XXX, 94389000, 98212000 (41x2), 93897000, 95008000, 13185000, 98750000, 98186000 (30x2), 98702000, 98212000 (41x2), 98190000 (36x2,5), 97523000, 97548000, 95049000, 96510000, G3/8 / G1/2, 93395000.

Zesis M33 150 Eco 1jet (74811000)

93735610, 98446000, 94390XXX, 94388XXX, 94389000, 98212000 (41x2), 93897000, 95008000, 13185000, 98750000, 98186000 (30x2), 98702000, 98212000 (41x2), 98190000 (36x2,5), 97523000, 97548000, 95049000, 96510000.

Zesis M33 150 CoolStart EcoSmart 1jet (74813000)

93735610, 98446000, 94393000, 94388000, 94389000, 98212000 (41x2), 93896000, 95008000, 13913000, 98186000 (30x2), 98324000, 98702000, 98212000 (41x2), 98190000 (36x2,5), 97523000, 97548000, 95049000, 96510000.

Zesis M33 160 1jet (74805000)

93735610, 98446000, 94390000, 94388000, 94389000, 98212000 (41x2), 93895000, 95008000, 13913000, 98750000, 98186000 (30x2), 98702000, 98212000 (41x2), 98389000 (25x2), 98158000 (39x2), 97523000, 97548000, 95049000, 94267000.

Zesis M33 200 CoolStart 1jet (74807000)

93735610, 98446000, 94393000, 94388000, 94389000, 98212000 (41x2), 93895000, 95008000, 13914000, 98186000 (30x2), 98324000, 98702000, 95629000, 98932000, 98212000 (41x2), 98817000, 97523000, 97548000, 97674000, 95049000, 96510000.

Zesis M33 200 1jet (74808000)

93735610, 98446000, 94390000, 94388000, 94389000, 98212000 (41x2), 93895000, 95008000, 13914000, 98186000 (30x2), 98750000, 98702000, 95629000, 98932000, 98212000 (41x2), 98817000, 97523000, 97548000, 97674000, 95049000, 96510000.

Dimensional Drawings

The document includes dimensional drawings for various Zesis M33 models, showing key measurements such as height, spout height, reach, installation hole diameter (Ø51 mm), base diameter (Ø34 mm), and operating angles for the handle (e.g., 60°, 110°, 150°, 360° rotation). Specific dimensions are provided for models like Zesis M33 150 1jet, Zesis M33 160 1jet, Zesis M34 150 1jet, Zesis M33 150 Eco 1jet, Zesis M33 150 CoolStart EcoSmart 1jet, Zesis M33 200 CoolStart 1jet, and Zesis M33 200 1jet. Connection sizes are indicated, such as G3/8, G1/2, and G3/4.

Flow Rate Diagrams

Performance curves are provided for various Zesis M33 models, illustrating the relationship between water flow rate (Q in liters per minute and liters per second) and water pressure (in MPa and bar). These charts help in understanding the faucet's performance under different pressure conditions.

Cleaning Recommendation and Warranty

The document provides cleaning recommendations and warranty information in multiple languages. Hansgrohe offers a warranty for its products. Specific contact information for warranty claims and cleaning advice is available on the website: www.hansgrohe.com/cleaning-recommendation. The warranty period is typically 5 years, as indicated by a graphic.