Teleco TXP/TAK Series Manual Transmitter

Product Overview

The Teleco TXP/TAK Series comprises UHF band manual transmitters featuring PLL or SAW controlled carrier frequency. These devices are designed for controlling domestic appliances, automatic openings, and managing ON/OFF or dimming functions for lights. They transmit a secure rolling code signal. The transmitter's code can be stored in the receiver either directly or wirelessly, simplifying the addition of new transmitters to existing systems without requiring direct access to the receiver unit. This process can be handled by the end-user. Codes are stored in the receiver's EEPROM memory, ensuring data retention even during temporary power outages.

Key Features and Specifications

Supported Models:

• TVTXP868xxxx
• TVTXP916xxxx
• TXP433xxxx
• TXP868xxxx
• TAK868xxxx

Technical Specifications:

Certifications:

The product is certified with R-NZ, UK CA, CE, FC, and IC.

Usage and Safety Information

General Safety Rules:

• Keep the transmitter out of the reach of children or animals.
• Avoid operating the transmitter in locations or systems sensitive to radio emissions, such as airports or hospitals.
• Do not store or use the transmitter in damp, humid, dusty environments, or areas exposed to direct sunlight.
• Store the transmitter in stable conditions to prevent damage or a reduction in its operational range.

Warnings:

KEEP OUT OF REACH OF CHILDREN.

DO NOT INGEST THE BATTERY, DANGER OF CHEMICAL BURNS.

• This product contains a coin/button cell battery. If swallowed, it can cause severe internal burns within 2 hours and may lead to death.
• Keep new and used batteries out of the reach of children.
• If the battery compartment does not close securely, discontinue use of the product and keep it out of the reach of children.
• If you suspect a battery has been swallowed or inserted into another body orifice, seek immediate medical attention.

EXPLOSION HAZARD IF THE BATTERY IS SUBSTITUTED INCORRECTLY.

• Replace the battery only with a CR2032 type battery.
• Always wrap the battery, whether stored or disposed of. Ensure it does not contact other metal objects, which could cause discharge, fire, or damage.
• Dispose of damaged or exhausted batteries immediately in accordance with legal provisions. Contact local environmental authorities or waste disposal services. Do not discard batteries in household waste.

Operational Notes:

• The transmitter is not protected against interference from other telecommunication equipment or systems operating on the same frequency range.
• If experiencing range issues, mount the transmitter in a raised position or replace the battery.
• During operation, maintain a distance of at least 5 mm from the radiating element.
• Transmitters are uniquely coded by the manufacturer with a different code for each unit.
• Transmission will automatically cease after a prolonged key press exceeding 30 seconds.

Transmitter Functions and Operation

Transmitter Key Configurations:

The transmitter is available with one, two, or four keys, designated CH1 through CH4, depending on the model.

• x01x (Single Button): Typical functions include ON, OFF, ON/OFF/Dim, ON/Color change/OFF, Open/Stop/Close.
• x02x (Single/Pairs Buttons): Typical functions include ON, OFF, ON/OFF/Dim, ON/Color change/OFF, Open/Stop - Close/Stop, and others.
• x04x (Single/Pairs Buttons): Typical functions include ON, OFF, ON/OFF/Dim, ON/Color change/OFF, Open/Stop - Close/Stop, and others.

A hidden P3 button is located on the back of the transmitter, used for receiver programming.

Battery Replacement:

Refer to Figure 2 for detailed battery replacement instructions. The process involves opening the transmitter casing, removing the old CR2032 battery, and inserting a new one, then closing the casing.

Wall Mounting:

A clip for wall mounting is supplied with the transmitter. Refer to Figure 3 for visual guidance on its use and the transmitter's dimensions (approximately 59mm, 13mm, 33mm).

Receiver Programming:

To memorize, delete, or copy a transmitter to a receiver, please follow the specific instructions provided with the receiver unit.

Declarations and Warranty

EU Conformity Declaration:

Teleco Automation S.r.l. hereby declares that the radio equipment type is in conformity with Directive 2014/53/EU. The complete text of the EU declaration of conformity is accessible at the following internet address: www.telecoautomation.com/ce

USA & Canada Conformity Declaration:

In accordance with FCC and ISED regulations, this device is designed as a mobile station. It complies with Part 15 of the FCC Rules and Industry Canada's licence-exempt RSSs. Operation is contingent upon two conditions: (1) the device must not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation. A minimum distance of 5 mm from the radiating element must be maintained during normal function. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Guarantee:

The guarantee is provided in compliance with legal provisions and is applicable only within the country where the manual transmitter was purchased. Batteries are explicitly excluded from the guarantee. For any warranty-related services, please refer to the specialized retailer.

Important Notes

In its ongoing commitment to product development, Teleco Automation reserves the right to implement changes to technical data and features without prior notification.