Milano Sofa Set

Before you start

Warnings

⚠️ IMPORTANT, RETAIN FOR FUTURE REFERENCE

READ CAREFULLY

See enclosed instructions for assembly, safety and care information.

Failure to follow the warnings could result in serious injury.

Handle heavy parts with care.

Ensure that this product is fully assembled as illustrated before use.

This product should only be used on firm, level ground.

Keep small parts out of reach of children.

Do not stand or climb onto this product.

This product is intended for domestic use only.

Furniture can be dangerous if incorrectly used. No liability will be accepted for damage or injury caused by incorrect use of this product.

Dos

✔️ When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for assembly.

✔️ Remove all packaging and banding and place the components carefully on suitable surfaces to prevent damaging or scratching them.

✔️ Check the pack and make sure you have all of the parts listed.

✔️ Check all screws and bolts are tightened and inspect regularly.

This product is suitable for all year outdoor use, but we recommend that a furniture cover be used to add additional protection to your product when not in use.

PLEASE NOTE - All cushions should be stored indoors after use. The cushions are not waterproof.

During severe weather conditions and in the winter months we recommend moving your furniture inside into a cool, dry place.

Before storage, ensure that the product is clean and dry.

To clean, wipe down with a sponge and warm soapy water and wipe with a clean, dry cloth.

Cushions should be cleaned following the care instruction on the label.

Don'ts

❌ Do not use scourers, abrasives, washing powders, chemical cleaners or any other substances containing abrasives since these substances can damage the product, including the glass panel.

❌ Never tilt the chair during use.

❌ Do not place very hot or very cold items on the glass surface unless adequately thick table-mats are used to prevent such items from coming into contact with the glass.

❌ Do not use the glass as a chopping surface. Do not strike glass with hard or pointed items.

❌ Do not strike the glass with hard or pointed items.

❌ Do not use power tools to construct this product.

❌ Do not use this product if parts are missing, damaged or worn.

❌ Do not sit or lean on the table.

❌ Do not stand or climb onto the product and do not use it as a ladder, as this could lead to it unbalancing and overturning.

❌ Never drag furniture when moving it, always lift it.

Number of people required for assembly: Two people

Time to assemble: 40 minutes

Tools required: Spanner (S1)

Tips:

Do NOT fully tighten bolts before all components are connected. Only fully tighten once you are satisfied with the alignment of all components. Do not overtighten bolts.

Member Parts

Components, Fixtures & Fittings (not actual size)

Step by step assembly instructions

MP1 – Coffee Table

Step One

Open the packaging, place the Coffee Table Glass Top (C) on the carton until the rest of the table is fully assembled.

With the help of another person, place Coffee Table Top (A) upside down on a flat, non-abrasive surface to avoid scratching the table surface or rim.

Diagram: A diagram showing the underside of the coffee table top (A) with space for legs.

Step Two

Loosely attach the Table Legs (B) to the Coffee Table Top (A) using Washers (F3) and Bolts (W15). Only tighten the bolts when all bolts and washers are in place. Once you are satisfied with the alignment of the components, carefully tighten all bolts using Spanner (S1). Do not over-tighten. Cover each bolt with Bolt Head Cap (F2).

Diagram: Close-up view showing a leg (B) being attached to the coffee table top (A) with a bolt (W15), washer (F3), and spanner (S1). Bolt head cap (F2) is also indicated.

Step Three

With the help of another person, carefully turn the table in the upright position. Level the table by adjustable foot screws.

Diagram: Shows the coffee table being turned upright, with a detail of adjustable foot screws at the bottom of the legs.

Step Four

With the help of another person, carefully turn the table in the upright position. Level the table by adjustable foot screws. Carefully place the Coffee Table Glass Top (C) on the Coffee Table Top (A). Your Coffee Table is now ready for use.

Diagram: Shows the coffee table upright with the glass top (C) being placed onto the table top (A).

MP2 – Armchair

Step One

Place the Armchair Seat (D) upside down. Attach Legs (F) and (G) to the Armchair Seat (D) using Washers (F3) and Bolts (W15). Once you are satisfied with the alignment of all components, carefully tighten all bolts using Spanner (S1). Cover each Bolt Head with Bolt Head Cap (F2).

Diagram: Shows the underside of the armchair seat (D) with legs (F and G) being attached using bolts (W15), washers (F3), and spanner (S1). Bolt head caps (F2) are indicated.

Step Two

Stand the Armchair and Level the Armchair by adjustable foot screws.

Diagram: Shows the assembled armchair standing upright, with a detail of adjustable foot screws.

Step Three

Place the Armchair Seat Cushion (H) and Armchair Backrest Cushion (J) onto the Armchair Seat (D). Your Armchair is now ready for use.

Diagram: Shows the armchair with seat cushion (H) and backrest cushion (J) placed.

MP2 – Loveseat

Step One

Place the Loveseat Seat (E) upside down. Attach Legs (F) and (G) to the Loveseat Seat (E) using Washers (F3) and Bolts (W15). Once you are satisfied with the alignment of all components, carefully tighten all bolts using Spanner (S1). Cover each Bolt Head with Bolt Head Cap (F2).

Diagram: Shows the underside of the loveseat seat (E) with legs (F and G) being attached using bolts (W15), washers (F3), and spanner (S1). Bolt head caps (F2) are indicated.

Step Two

Stand the Loveseat and Level the Loveseat by adjustable foot screws.

Diagram: Shows the assembled loveseat standing upright, with a detail of adjustable foot screws.

Step Three

Place the Loveseat Seat Cushion (I) and Loveseat Backrest Cushion (K) onto the Loveseat Seat (E). Your Loveseat is now ready for use.

Diagram: Shows the loveseat with seat cushion (I) and backrest cushion (K) placed.

Important Note: Never tilt the product during use. Ensure the product is always placed firmly on the ground.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Produced in China for A Mir & Co., Ltd. © A Mir & Co., Ltd.

Visit: www.royalcraft.co.uk