Royalcraft ZPA002/ZPA004 Modular Furniture Assembly Guide
Models: ZPA002, ZPA004
Assembly Instructions
Carefully unpack all components and verify that all necessary parts are included as listed in the packaging. Identify each component and refer to the provided assembly diagrams or step-by-step instructions. Assemble the furniture in the order specified to ensure proper alignment and fit. Use the provided tools or recommended tools for assembly. Do not use excessive force when tightening screws or bolts. If any difficulties arise during assembly, consult the troubleshooting section or contact customer support.
Corner Chair Assembly
Tools Required
Allen Wrench (V)
Parts List
| NO. | PART DESCRIPTION | QTY | NO. | PART DESCRIPTION | QTY | NO. | PART DESCRIPTION | QTY |
|---|---|---|---|---|---|---|---|---|
| D | Base/Back Panel | 1 | M | Support Piece | 1 | R | Seat Cushion | 1 |
| E | Side Panel | 1 | N | M6x25mm Screw | 8 | S | Back Cushion | 1 |
| F | Base Panel | 1 | O | M6x30mm Screw | 12 | T | Frame Component | 1 |
| C | Front Panel | 1 | P | Screw/Bolt | 1 | V | Allen Wrench | 1 |
| L | Corner Bracket | 3 | Q | Washer/Nut | 12 |
Assembly Steps
Step 1
Attach side panel (E) to the base/back panel (D) using one screw (P) and one washer/nut (Q). A close-up view shows the screw passing through pre-drilled holes.
Step 2
Attach two side panels (E) to the base/back panel (D) using screws (P) and washers/nuts (Q). This forms a U-shaped structure.
Step 3
Attach the base panel (F) to the bottom of the U-shaped structure using screws (O) and washers/nuts (Q).
Step 4
Attach the front panel (C) to the front of the structure using screws (O) and washers/nuts (Q).
Step 5
Secure the structure by attaching corner brackets (L) to the inside corners using screws (N) and brackets (L). Attach the support piece (M) using screws (N) and brackets (L).
Step 6
Place the seat cushion (R) and back cushion (S) onto the assembled frame. Part T is also shown.
Armless Chair Assembly
Tools Required
Allen Wrench (V)
Parts List
| NO. | PART DESCRIPTION | QTY | NO. | PART DESCRIPTION | QTY | NO. | PART DESCRIPTION | QTY |
|---|---|---|---|---|---|---|---|---|
| A | Side Panel | 1 | M | Support Piece | 2 | R | Seat Cushion | 1 |
| B | Base/Back Panel | 1 | N | M6x25mm Screw | 8 | S | Back Cushion | 1 |
| C | Front/Side Panel | 2 | O | M6x30mm Screw | 10 | V | Allen Wrench | 1 |
| L | Corner Bracket | 2 | Q | Washer/Nut | 10 |
Assembly Steps
Step 1
Attach side panel (A) to the base/back panel (B) using one screw (Q) and one washer/nut (Q).
Step 2
Attach two front/side panels (C) to the structure formed in Step 1 using screws (Q) and washers/nuts (Q).
Step 3
Secure the structure by attaching corner brackets (L) to the inside corners using screws (N) and brackets (L). Attach the support piece (M) using screws (N) and brackets (L).
Step 4
Place the seat cushion (R) and back cushion (S) onto the assembled frame.
Connecting Units
Plastic Clip Required
To connect two assembled chair units, use the provided plastic clips. Insert the clips into the designated slots on the sides of the units to join them securely. The carton contains 4 clips for connecting units.
Maintenance and Care
- Protect your furniture from extreme weather conditions by moving it to a covered area or using furniture covers.
- Avoid dragging or placing heavy objects on the furniture to prevent potential damage.
- Regularly inspect your furniture for signs of wear, loose strands, or damage and address any issues promptly.
- Hardware may loosen over time. Periodically check all connections and re-tighten if necessary.
- Do not dispose of packaging or carton contents until assembly is completed to avoid accidentally discarding small parts or hardware.
- Do not use sharp objects that may scratch the painted surface.
- Clean with a damp cloth soaked in warm soapy water or a specialized cleaning product.
- Conclude cleaning by wiping with a clean, dry cloth.
- Ensure proper drying after cleaning or exposure to rain to prevent mold or mildew growth.
Warranty Information
Warranty Coverage
Our warranty provides protection against manufacturing defects in materials and workmanship for a specified period from the date of purchase, as outlined in the accompanying warranty documentation.
Exclusions
The warranty does not cover damages resulting from misuse, negligence, accidents, normal wear and tear, unauthorized repairs or modifications, improper assembly, or failure to adhere to the care and maintenance guidelines provided.
Contact Information
If you have any questions, concerns, or need assistance, please reach out to the customer support team using the contact information provided below:
Customer Support Email: support@royalcraft.store ?
