Assembly Instruction

Important Notice Before Assembly

PLEASE READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE ATTEMPTING TO ASSEMBLE, OPERATE OR INSTALL THE PRODUCT.

Notice:

1. Tighten screws to 50% before fixing all screws. An Allen wrench is recommended over an electric drill.
2. Place the item on a flat ground to adjust and ensure it remains stable.
3. Tighten all screws gradually using tools.
4. If screws do not align with holes during assembly, loosen all other screws to 50% and continue the assembly process.
5. If the item is not stable, loosen all screws, adjust it on a flat ground, and then tighten all screws again.
6. Note: If some screws are fully tightened during assembly, others may not align with holes. The holes are designed to be larger to provide more space for screw adjustment.

Parts List

• G x1: Right Leg Fire Table
• H x1: Left Leg Fire Table
• I x1: Back Frame Fire Table
• J x1: Front Frame Fire Table
• K x1: Top Fire Table
• L x1: Burner
• M x1: Gas Valve
• N x1: Burner Tube
• O x1: Lid
• Q x1: Burner Glass
• R x2: Short Glass
• S x2: Long Glass
• AA x1: Tube (NOT INCLUDED)
• AB x2 KG: Lava Rocks
• AC x1: The Propane Tank (NOT INCLUDED)

Take note: supply pressure less than 0.5 PSI

Hardware List

• 1 x16 pcs: BOLT M6 x 8MM
• 2 x4 pcs: BOLT M6 x 15MM
• 3 x16 pcs: BOLT M6 x 40MM
• 4 x16 pcs: FLAT WASHER M6
• 5 x8 pcs: GLASS CONNECTOR 1
• 7 x1 pc: ALLEN KEY M4
• 8 x1 pc: LOCK
• 9 x2 pcs: PLASTIC WASHER
• 10 x1 pc: BATTERY AAA (not included)
• 11 x1 pc: CRESENT WRENCH 20
• 12 x1 pc: CRESENT WRENCH 25
• 13 x16 pcs: PLASTIC COVER
• 14 x2 pcs: KNOB M6
• 15 x1 pc: CRESENT WRENCH 8

Assembly Steps

STEP 1

Connect Right Leg Fire Table (G) & Top Fire Table (K). Tighten Bolt (3) & Flat Washer (4) with Allen Key (7).

[Diagram showing connection of G and K with bolts and washers]

STEP 2

Connect the part from step 1 & Front Frame Fire Table (J). Tighten Bolt (3) & Flat Washer (4) with Allen Key (7).

[Diagram showing connection of J to the assembly from Step 1]

STEP 3

Connect the part from step 2 & Back Frame Fire Table (I). Tighten Bolt (3) & Flat Washer (4) with Allen Key (7).

[Diagram showing connection of I to the assembly from Step 2]

STEP 4

Connect the part from step 3 & Left Leg Fire Table (H). Tighten Bolt (3) & Flat Washer (4) with Allen Key (7).

[Diagram showing connection of H to the assembly from Step 3]

STEP 5

Adjust for balance.

[Diagram showing adjustment of the fire table for stability]

STEP 6

Attach the locking part (8) with plastic washer (9), knob (14).

[Diagram showing attachment of lock, plastic washer, and knob]

STEP 7

Put on Burner Glass (Q) to the part from step 6.

[Diagram showing placement of burner glass]

STEP 8

Connect Burner (L) & Gas Valve (M) with Crescent Wrench 25 (12).

[Diagram showing connection of burner and gas valve]

STEP 9

Connect Tube (AA) & Propane Tank (AC) with Crescent Wrench 20 (11). (not included)

Take note: supply pressure less than 0.5 PSI

[Diagram showing connection of tube and propane tank]

STEP 10

Place the part from step 8 to the part from step 7. Place the tube as shown in the picture.

[Diagram showing placement of burner assembly and tube]

STEP 11

Place the tube of propane tank (AC) (not included) as shown in the picture.

Take note: supply pressure less than 0.5 PSI

[Diagram showing placement of propane tank tube]

STEP 12

Check that the Gas Valve (M), for the gas supply system is turned to the OFF position before starting any assembly.

Connect thermocouple (L1) to ignition module hole (M1) of Gas Valve.

Connect Orificecouple (L2) to Control Knor (M2) of Gas Valve with cresent wrench 8 (15).

Connect Gas Outlet Tube (N) to Outlet Hole of Gas Valve with Cresent Wrench 20 (11) in the direction of the arrow.

[Diagram showing detailed connections to the gas valve]

STEP 13

Connect Gas Inlet Tube of Propane Tank (AA) to Inlet Hole of Gas Valve with Cresent Wrench 20 (11) in the direction of the arrow. (as shown in the picture)

[Diagram showing connection of propane tank tube to gas valve]

STEP 14

Connect the part from step 13 & Gas Valve (M), Propane Tank (AA) with Tighten Bolt (3) & Flat Washer (4) with Allen Key (7).

[Diagram showing final connections and tightening]

STEP 15

Open the igniter cover and place the battery AA (8) (not included) into it. Then tighten the igniter cover completely.

PLEASE READ AND UNDERSTAND ATTACHED WARNING AND OPERATION DOCUMENT BEFORE ATTEMPTING TO OPERATE OR INSTALL THE PRODUCT.

[Diagram showing igniter cover and battery installation]

STEP 16

Put on Plastic Cover (13) to Corner of Short Glass (R) and Long Glass (S). Connect Short Glass (R) & Long Glass (S) with Tighten Bolt (1) & Glass Connector 1 (5) with Allen Key (7).

CAUTION! Handle the glass with care when assembling.

[Diagram showing attachment of glass pieces with bolts and connectors]

STEP 17

Put on the part from step 16 to the part from step 15.

[Diagram showing placement of assembled glass onto the fire pit]

STEP 18

Pour ALL lava rocks (AB) into the burner pan. The burner MUST be completely covered to ensure the appliance functions properly and safely. Remove any lava rocks (AB) on top of the ignition well.

[Diagram showing pouring of lava rocks into the burner pan]