Assembly Instruction

Product Identification

Model Numbers: N704P239430; N704P239431

Assembly Notice

1. Tighten screws to 50% before fixing all screws. An Allen wrench is recommended over an electric drill.
2. Place the item on a flat ground to adjust and ensure stability.
3. Gradually tighten all screws with tools.
4. If screws do not align with holes during assembly, loosen other screws to 50% and continue assembly.
5. If the item is unstable, loosen all screws, adjust on a flat ground, and retighten all screws.
6. Note: Fully tightening some screws early may misalign other holes. All holes are designed to be larger for easier adjustment.

Parts List

• A: Right Leg (4 pcs)
• B: Seat Chair Frame (4 pcs)
• C: Left Leg (4 pcs)
• D: Back Chair Frame (4 pcs)
• E: Leg Stool (8 pcs)
• F: Seat Stool Frame (4 pcs)
• G: Support stool (4 pcs)
• H: Top Table (1 pc)
• I: Table Leg Middle (1 pc)
• J: Table Leg Left (2 pcs)
• K: Seat Cushion (4 pcs)
• L: Back Cushion (4 pcs)
• M: Seat Stool Cushion (4 pcs)

Hardware

• 1: BOLT M6 x 20MM (60 pcs + 2 extra)
• 2: BOLT M6 x 35MM (64 pcs + 2 extra)
• 3: FLAT WASHER M6 (124 pcs + 3 extra)
• 4: CONNECTOR (8 pcs)
• 5: ALLEN KEY (2 pcs)

Carton Content

N704P239430

• E x 8
• F x4
• G x 4
• H x1
• I x 1
• J x 2
• M x 4

N704P239431

• A x4
• B x4
• C x 4
• D x 4
• K x 4
• L x 4
• Hardware

Assembly Steps

Step 1

Connect Seat Chair (B) & Back Chair (D). Tighten Bolt (2) & Flat Washer (3) with Allen Key (5). (x4)

Step 2

Connect the part from Step 1 & Right Leg (A). Tighten Bolt (2) & Flat Washer (3) with Allen Key (5). (x4)

Step 3

Connect the part from Step 2 & Left Leg (C). Tighten Bolt (2) & Flat Washer (3) with Allen Key (5). (x4)

Step 4

Connect the part from Step 3 & Connector (4). Tighten Bolt (1) & Flat Washer (3) with Allen Key (5). (x4)

Step 5

Connect the part from Step 4. Tighten Bolt (2) & Flat Washer (3) with Allen Key (5). (x4)

Step 6

Open all bags, adjust cushions. Set up Seat Cushions (K) + Back Cushion (L). (x4)

Step 7

Finish Chair. (x4)

Step 8

Connect Leg Stool (E) & Seat Stool Frame (F). Tighten Bolt (2) & Flat Washer (3) with Allen Key (5). (x4)

Step 9

Connect the part from Step 8. Tighten Bolt (1) & Flat Washer (3) with Allen Key (5). (x4)

Step 10

Connect the part from Step 9 & Leg Stool (E). Tighten Bolt (2) & Flat Washer (3) with Allen Key (5). (x4)

Step 11

Connect the part from Step 10. Tighten Bolt (1) & Flat Washer (3) with Allen Key (5). (x4)

Step 12

Connect the part from Step 11 & Support stool (G). Tighten Bolt (1) & Flat Washer (3) with Allen Key (5). (x4)

Step 13

Open all bags, adjust cushions. Set up the Seat Stool Cushion (M). (x4)

Step 14

Finish Stool. (x4)

Step 15

Connect Top Table (H) & Table Leg Middle (I). Tighten Bolt (1) & Flat Washer (3) with Allen Key (5). (x4)

Step 16

Connect the part from Step 15 & Table Leg Left (J). Tighten Bolt (1) & Flat Washer (3) with Allen Key (5). (x4)

Step 17

Finish Table.

Step 18

Finish.