TABLE SET

Important Safety and Care Advice

Important: Please read these instructions fully before starting assembly.

• Check you have all the components and tools listed on the following pages.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area; small parts could cause choking if swallowed.
• Make sure you have enough space to lay out the parts before starting.
• During assembly, do not stand or put weight on the product, as this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft, level surface to avoid damaging the unit or your floor.
• Assembly will be easier with 2 people.
• To reduce the likelihood of damaging your product, please ensure that your power drill is set to a low torque setting.

Care and Maintenance

• Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
• From time to time, check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take it to your local authority waste disposal center.

Handy Hints

• Assemble all parts and bolts loosely during assembly. Only fully tighten the bolts once the product is complete.
• Regularly check and ensure that all bolts and fittings are tightened properly.

WARNING: In order to help prevent overturning - please follow these instructions

To help prevent product toppling over, please follow the below steps:

• Use the anti-tip strap or wall-fixing method provided (if applicable).
• Do not allow children to climb or hang on the furniture.
• Do not open more than one drawer at a time.
• Do not place heavy items in the top drawers.
• Do not place heavy items on top of the furniture, unless the furniture has been designed for this purpose.

Please note that only the anti-tip strap is provided. You will need to provide wall plugs and screws applicable for your wall type.

Assembly Instruction Diagram

The following diagrams illustrate the assembly process. Parts are labeled with numbers corresponding to the Part List.

Part List (N844P285188):

Hardware List (N844P285188):

Assembly Tools Required (Not Included):

Use this ruler to help correctly identify the screws:

[Ruler image showing measurements from 5 to 100mm]

The screw length is measured from the head to the point (35mm screw shown).

Step 1:

Attach side panels (2, 3) to the bottom panels (6A, 6B) using hardware A, B, and C. Use Allen key D for tightening.

[Diagram showing Step 1 assembly]

Step 2:

Attach side panels (4, 5) to the bottom panels (6A, 6B) using hardware A, B, and C. Use Allen key D for tightening.

[Diagram showing Step 2 assembly]

Step 3:

Connect the assembled sides using the fixed shelf (9) and bottom panels (6A, 6B) with hardware A and B.

[Diagram showing Step 3 assembly]

Step 4:

Attach the back panels (7) and back panel (10) to the main structure.

[Diagram showing Step 4 assembly]

Step 5:

Step 5.1: Place the table top (1) onto the assembled structure.

Step 5.2: Secure the table top.

[Diagram showing Step 5 assembly]

Step 6:

Attach the table legs (12) to the bottom panels using hardware E. Ensure 4 legs are attached.

[Diagram showing Step 6 assembly]

Step 7:

Attach the remaining table legs (12) using hardware E and F.

[Diagram showing Step 7 assembly]

Step 8:

Install the USB power outlet (H) onto the desk surface using screws G.

[Diagram showing Step 8 assembly]

Step 9:

Step 9.1: Assemble the drawer components: front panel (13), left side panel (16), and right side panel (15).

Step 9.2: Insert the drawer bottom panel (14).

[Diagram showing Step 9 assembly]

Step 10:

Step 10.1: Slide the drawer bottom panel (14) into place.

Step 10.2: Attach drawer handles (J) and drawer back panel (17) using hardware I and K.

[Diagram showing Step 10 assembly]

Step 11:

Insert drawer dividers (18, 19) into the assembled drawer.

[Diagram showing Step 11 assembly]

Step 12:

Slide the completed drawer into the desk.

[Diagram showing Step 12 assembly]

Step 13:

Attach hinges (L) to the left side door (11A) and right side door (11B) using hardware E.

[Diagram showing Step 13 assembly]

Step 14:

First, install hinges with 2 screws in oval holes for door adjustment. Then, install the other 2 screws after doors are adjusted. Repeat for both doors (11A, 11B).

[Diagram showing Step 14 assembly]

Step 15:

Attach cabinet door handles (M) to the doors (11A, 11B) using hardware P.

[Diagram showing Step 15 assembly]

Step 16:

Insert adjustable shelves (8) into the desk using shelf pins (N).

[Diagram showing Step 16 assembly]

Step 17:

Anti-tip strap installation:

Mark positions on the wall, 700mm and 975mm from the floor. Attach the anti-tip strap (S-2) to the wall using wall plugs (S-3) and screws (S-4). Attach the other end of the strap to the furniture using screw (S-5).

[Diagram showing Step 17 assembly]

Step 18:

Secure the anti-tip strap (S-2) to the furniture using screws (S-5).

[Diagram showing Step 18 assembly]

Step 19:

Attach the anti-fall set (S-1) to the furniture.

[Diagram showing Step 19 assembly]

Step 20:

Assemble the stool by attaching the stool legs (21) to the cushion (20) using hardware O and D.

[Diagram showing Step 20 assembly]

FINISH

Your table set is now assembled.

[Diagram showing the completed table set and stool]