Make Up Cart
Assembly Instructions - N704P196658
Please keep for future reference
If you have any questions, please feel free to contact us.
Email: hdteam@aminalife.com
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
- Check you have all the components and tools listed on the following pages.
- Remove all fittings from the plastic bags and separate them into their groups.
- Keep children and animals away from the work area; small parts could choke if swallowed.
- Make sure you have enough space to lay out the parts before starting.
- During assembly, do not stand or put weight on the product, this could cause damage.
- Assemble the item as close to its final position (in the same room) as possible.
- Assemble on a soft level surface to avoid damaging the unit or your floor.
- Parts of the assembly will be easier with 2 people.
- To reduce the likelihood of damaging your product, please ensure that your power drill is set on a low torque setting.
- Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.
- From time to time, check that there are no loose screws on this unit.
- This product should not be discarded with household waste. Take it to your local authority waste disposal centre.
- Assemble all parts and bolts loosely during assembly; only once the product is complete should you fully tighten the bolts.
- Regularly check and ensure that all bolts and fittings are tightened properly.
WARNING
In order to help prevent overturning – please follow these instructions
To help prevent product toppling over, please follow the below steps:
- Use the anti-tip strap or wall fixing method provided (if applicable).
- Do not allow children to climb or hang on the furniture.
- Do not open more than one drawer at a time.
- Do not place heavy items in the top drawers.
- Do not place heavy items on top of the furniture, unless the furniture has been designed for this purpose.
Using Camlocks
Step 1
Connect the male camlock as directed in the assembly instructions using a screwdriver. [DO NOT OVER TIGHTEN.]
Visual description: A diagram showing a male camlock being screwed into a panel.
Step 2
Push the male camlock into the entry hole.
Visual description: A diagram showing the male camlock being inserted into a pre-drilled hole.
Step 3
Insert the female camlock as shown in the instruction. Note: ensure that the arrow on the top of the camlock points towards the entry hole for the male camlock.
Visual description: A diagram showing the female camlock being inserted into its corresponding hole, with an arrow indicating the correct orientation.
Step 4
Turn the female camlock clockwise with a screwdriver. You should feel a click when the camlock is locked in place. The joint is now secure.
Visual description: A diagram showing a screwdriver turning the female camlock, with an indication of the locking mechanism.
Components - Key Diagram
Visual description: An exploded view diagram showing all the components labeled with letters A through F.
- A: Mirror Frame
- B: Desk Top
- C: Back Panel (x2)
- D: Left Side Panel
- E: Right Side Panel
- F: Connect Wood (x2)
Part List
| Component | Description | Quantity |
|---|---|---|
| A | Mirror Frame | 1 |
| B | Desk Top | 1 |
| C | Back Panel | 2 |
| D | Left Side Panel | 1 |
| E | Right Side Panel | 1 |
| F | Connect Wood | 2 |
Hardware List
| Item | Description | Quantity |
|---|---|---|
| 1 | Cam Bolt | 8 |
| 2 | Cam Lock | 8 |
| 3 | Wood Dowel | 4 |
| 4 | Bracket | 2 |
| 5 | Bracket | 2 |
| 6 | Flat Screw (Ø8*18mm) | 24 |
| 7 | Cam Tool | 1 |
| 8 | Adaptor | 1 |
| 9 | Plastic Tie | 2 |
| 10 | Screw (Ø1/4*38mm) | 8 |
| 11 | Spring Washer | 8 |
| 12 | Flat Washer | 8 |
| 13 | Handle | 1 |
| 14 | Bolt (Ø8*25mm) | 2 |
| 15 | Allen Key | 1 |
| 16 | Round Head Screw (Ø7*15mm) | 4 |
| 17 | Hook | 4 |
| 18 | Flat Head Screw (Ø8*38mm) | 4 |
| 19 | Anchor | 4 |
Assembly Steps
Step 1
Attach side panels (D) to the back panels (C) using cam bolts (1), cam locks (2), and wood dowels (3). Ensure 4 cam bolts, 4 cam locks, and 2 wood dowels are used per side.
Visual description: Diagram showing the attachment of side panels to back panels with hardware.
Step 2
Attach the other side panel (E) to the back panels (C) using cam bolts (1), cam locks (2), and wood dowels (3). Ensure 4 cam bolts, 4 cam locks, and 2 wood dowels are used per side.
Visual description: Diagram showing the attachment of the second side panel to the back panels with hardware.
Step 3
Attach the mirror frame (A) to the desk top (B) using screws (6). Two screws are used.
Visual description: Diagram showing the mirror frame being attached to the desk top with screws.
Step 4
Attach brackets (5) to the underside of the desk top (B) using screws (6). Two brackets are used, each secured with 6 screws.
Visual description: Diagram showing brackets being attached to the desk top with screws.
Step 5
Connect the assembled side panels (D, E) to the desk top assembly (B) using cam bolts (1), cam locks (2), and wood dowels (3). Ensure 4 cam bolts, 4 cam locks, and 2 wood dowels are used per side.
Visual description: Diagram showing the main structure of the desk being assembled.
Step 6
Slide the back panels (C) into the grooves on the side panels (D, E).
Visual description: Diagram showing the back panels being slotted into place.
Step 7
Attach the handle (13) to the drawer front using bolts (14). One handle and two bolts are used.
Visual description: Diagram showing the handle being attached to the drawer front.
Step 8
Secure the drawer assembly using cam bolts (10), cam locks (11), cam locks (12), and plastic ties (9). Ensure 4 cam bolts, 4 cam locks, and 4 cam locks are used, along with 1 plastic tie.
Visual description: Diagram showing the drawer assembly being secured.
Step 9
Repeat Step 8 for the other side of the drawer assembly.
Visual description: Diagram showing the other side of the drawer assembly being secured.
Step 10
Attach the mirror frame assembly (A+B) to the main desk structure (D+E+C) using the provided fittings.
Visual description: Diagram showing the mirror frame assembly being attached to the main desk structure.
Step 11
For safety, secure the Make Up Cart to the wall using the anti-tip hardware. Use hooks (17), screws (16), anchors (19), and screws (18). Ensure 2 hooks, 2 screws, 2 anchors, and 2 screws are used for wall attachment.
Visual description: Diagram showing the anti-tip hardware being installed to secure the unit to a wall.
Related Documents
 |
Make Up Table Assembly Instructions - N704P196657 Assembly instructions for the Make Up Table model N704P196657. Includes parts list, hardware list, and step-by-step assembly guide. |
 |
Assembling Instructions for Glass Top Table Detailed assembly instructions for a glass top table, including a parts list and step-by-step guidance. Learn how to assemble your table with ease. |
 |
Assembly Instructions for Table Set N844P285188 Comprehensive assembly instructions for the N844P285188 table set, including a parts list, hardware list, and step-by-step guidance for assembly. Safety and care advice are also provided. |
 |
Assembly Instructions for N707P210158 Fire Pit Table Comprehensive assembly instructions for the N707P210158 Fire Pit Table, including a detailed parts list, hardware list, and step-by-step assembly guide. |
 |
Assembly Instructions for Aminalife Kitchen Island Cart N707P307296 Detailed assembly instructions for the Aminalife Kitchen Island Cart, model N707P307296. Includes a comprehensive parts and hardware list, followed by step-by-step guidance for assembling the kitchen island. |
 |
Fire Pit Table Assembly Instructions Comprehensive assembly instructions for the N707P210158 Fire Pit Table, including parts list, hardware list, and step-by-step assembly guidance. |
 |
Assembly Instructions for N704P210496K Comprehensive assembly instructions for the N704P210496K, detailing part identification, assembly steps, and care recommendations. |
 |
Assembly Instructions for Dining Set Detailed assembly instructions for a dining set, including parts list, hardware, and step-by-step guidance for chairs, stools, and the table. |