Safety Warnings
⚠️ WARNING:
- Do not look directly into the light beam or shine it directly into the eyes of other people.
- Do not touch the light case or LED when the light is on as they can become very hot.
- Keep light out of reach of children.
- RECON E HL LED lights have a water resistance rating of IPX6 under regular daily use and are not designed to be submerged in water. Submerging RECON E HL LED lights under water will damage the light and void the warranty.
- Do not attempt to disassemble or repair the light; doing so will void the warranty.
- Be sure to direct the light beam downward to avoid blinding oncoming pedestrians or drivers.
- Do not use high mode on public roads.
- Before your ride, please make sure the light is firmly mounted to the bracket, that it functions correctly and is not blocked by baggage, etc.
- In case of unexpected light shutoff or battery issues, carrying a spare light is recommended.
- If the light, light case or accessories become dirty with mud or dust, clean them with a soft cloth moistened with mild soap. Never use alcohol, benzene or solvents, doing so will result in damage and void the warranty.
Giant Bicycles Inc. does not accept any liability for injuries or other damages resulting from the improper use or improper installation of this product under any circumstance.
Introduction and Usage Notes
? NOTE:
To ensure proper use and care of your new RECON E HL LED lights, please read the entire manual before installation and operation.
Traffic laws mandating bicycle lights vary from country to country. Please make sure you are following the appropriate bicycle light laws and regulations in your country of use.
RECON E HL LED lights can be controlled via the on-board electronics of your E-bike system and are only to be mounted on E-bikes with DC voltage that have their own battery charge indication and control. The E-bike system must also be capable of automatically shutting the light off when the on-board battery reaches critical voltage to avoid deep battery discharge.
RECON E HL LED lights are powered by the motor of your E-bike and need to be manually installed. Depending on make and model/battery type, correct installation may require some disassembly of the bike and motor and additional wiring to connect the light to the motor. Please follow the appropriate Giant How-To video for correct installation on your model / battery type or contact the e-bike or motor manufacturer for installation instructions.
? NOTE:
Incorrect disassembly, installation or assembly may void the warranty of your e-bike and/or light. It is highly recommended that a trained E-bike technician install your lights.
Aligning the RECON E HL Beam
Follow these steps to achieve a glare-free beam compliant with German road law:
- Place the bike 2.5 meters away from a wall and face your bike towards the wall.
- Turn on the RECON E HL and set it to high-beam mode.
- Ensure the light is parallel to the ground.
- Mark the cut-off line of the beam on the wall, where the beam ends above and is brighter below.
- Measure and mark 7 cm below the cut-off line.
- Adjust the RECON E HL so the height of the beam matches the new, lower cut-off line.
? NOTE:
Make sure to follow the steps above to achieve a glare-free beam that is compliant with German road law.
Distance to the wall: 2.5 m
Recommended beam height: Between 70-120 cm
Diagram Description: Visual guide for aligning the headlight beam against a wall, showing the light's position and the desired cut-off line.
Connection and Compatibility
Link to Video Tutorials: ▶️ www.giant-bicycles.com/global/recon-e-lights
The Giant / Yamaha motor cable is included with the light.
Cables for non-Yamaha motors are not included and must be purchased separately. Contact your authorized Giant retailer for more information.
Diagram Description: Illustration showing the light's connection port (RED and WHITE wires indicated) and separate diagrams for optional motor cables for Brose, Bosch, and Shimano motors.
Motor Compatibility:
- Bosch (6V) / Bosch (12V)
- Shimano E5000, E7000, E6100, E6110, E9000
- Shimano E6000, E6001, E6010, E6050
- Shimano E8000, E8080, E6002, E6012
- Yamaha PWse / Yamaha PW
- Brose Drive S (2018)
Technical Data
| Specification | Details |
|---|---|
| Brightness | 400 Lumen, 100 Lux (Low Beam) |
| Wattage | 5 W |
| Input Voltage | 6-48V DC |
| Illuminant | 1 LED |
| Power Cable Length | 60 cm |
Warranty Information
- In the U.S.A. and U.K., RECON E HL LED Lights carry a two (2) year warranty to the original owner from the original purchase date (proof of purchase required).
- RECON E HL warranties cover all manufacturing defects in materials or workmanship.
- For all warranty issues worldwide, please contact an authorized Giant retailer and present proof of purchase.
- If an LED is not working correctly or not working at all, do not use your light anymore. The light will need to be replaced immediately.
- Normal wear and tear or damage arising from improper installation, attempting to access or modify electronics, accidents, misuse, abuse, and/or neglect are not covered by the warranty.
