GIANT Recon Plus HL 2600 Bicycle Light Manual

! WARNING/CAUTION

• This light emits an extremely powerful beam equivalent to an automobile headlight, which may cause a hazardous situation depending on the beam angle used.
• Be sure to direct the light beam downward so approaching drivers are not dazzled.
• Do not use high mode on public roads.
• Before your trip, please ensure the light is firmly mounted to the bracket, it lights up, and is not blocked by baggage, etc.
• Do not stare at the light while it is illuminating, as it may damage your eyesight.
• Do not place it within children's reach.
• In preparation for unexpected battery shutoff, it is recommended to carry a spare light.
• This product is water-resistant under normal daily use and can be used in the rain. However, do not intentionally submerge it in water.
• If the light unit or parts become dirty with mud, etc., clean with a soft cloth moistened with mild soap. Never apply paint thinner, benzine, or alcohol, as damage will result.
• This unit is shipped with a small charge to check the light. Be sure to charge it before use, according to the instructions "HOW TO CHARGE".

Product Components and Features

Illustration showing the bicycle light unit with a CNC casing, a USB C cable, a handlebar mount designed for 31.8-35mm diameter handlebars, an adjustable GoPro-style mount, and a separate remote control.

Key Features:

• Max Output: 2600 Lumens
• Blind Spot Monitoring System: Pairing RECON + TL300 R to active function
• Modes: Full power mode, Power/Mode switch

Switching the Lighting Mode

Power Lock: Press for 7 sec for power lock/ unlock. The power lock function prevents accidental switching on of the light in the backpack or suitcase.

Mode Switching: The light offers 'Cutoff beam (High ➔ Mid ➔ Low ➔ Flash)' and 'High beam On ➔ Off' functions.

The light unit features two buttons: 'Full Power switch' and 'Beam mode'.

How to Charge

Always charge the product before use.

Charging Status Indicators:

• GREEN FLASHES: Charging
• GREEN ILLUMINATES: Fully Charging

Battery Level Indicators:

• GREEN: 100%
• ORANGE: 50%
• RED: 20%

How to Install

Pairing

Step 1: Turn on the car lights. Press both buttons on the remote control simultaneously for 5 seconds to initiate pairing mode.

Step 2: The pairing is successful when the remote control's blue light flashes, followed by the green light turning on for 3 seconds before turning off.

Step 3: During the initial pairing, ensure there are no nearby lights from the same RECON PLUS series.

How to Mount to a Helmet/Computer Extension Mount

The mounting process may involve a mounting buckle and/or thumb screw, depending on the mount you are using.

Standard Handlebar Mounting (31.8-35mm)

Step 1: Secure the mount to the handlebar.

Step 2: Attach the light unit to the mount using the M3 screw. A click indicates proper attachment. Torque specification: 5 kgf/cm (0.5 Nm).

Aero Shape Handlebar Mounting

Step 1: Secure the mount to the aero-shaped handlebar.

Step 2: Attach the light unit to the mount using the M3 screw. A click indicates proper attachment. Torque specification: 5 kgf/cm (0.5 Nm).

Computer Extension Mount

Illustration showing how to attach the light unit to a computer extension mount, allowing for adjustable angle options.

Regulatory Information

FCC ID: ZL7-RECONHL2600

IC: ZL7-RECONHL2600

Operating Frequency: 2457MHz

Transmitter power: <4dBm

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Compliance

PMN/Product name: Bicycle light

Model name: Recon plus HL 2600

IC: ZL7-RECONHL2600

HVIN: RECON PLUS HL2600

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation.

Canadian Compliance (French)

Ce dispositif se conforme aux RSS exonérés de licence d'Industrie Canada.

L'opération est assujettie aux règles suivantes:

• (1) Ce dispositif ne doit pas causer d'interférence et
• (2) Ce dispositif doit accepté les interférences, même celles causées par la mauvaise opérarion du dit dispositif.

Ce dispositf rencontre toutes les exemptions de la section 2.5 du RSS-102 sur les limites d'évaluation de routine et Se conforme au RRS-102 exposition au RF. pour plus de renseignements contactez l'information canadienne sur l'exposition et conformité au RF.

RED Declaration of Conformity (DOC)

Unique identification of this DoC:

We, Giant Manufacturing CO., Ltd., declare under our sole responsibility that the product:

• Product name: Bicycle light
• Trade name: GIANT
• Type or model: Recon plus HL 2600

to which this declaration relates is in conformity with the essential requirements and other relevant requirements of the RED Directive (2014/53/EU).

The product is in conformity with the following standards and/or other normative documents:

• HEALTH & SAFETY (Art. 3(1)(a)): EN 60598-2-8:2013, EN 60598-1:2015, EN 62493:2015, EN62479:2010
• EMC (Art. 3(1)(b)): Draft EN 301 489-1 V2.2.0:2017, Draft EN 301 489-17 V3.2.0:2017; EN 55015:2013+A1:2015; EN 61547:2009
• SPECTRUM (Art. 3(2)): EN 300 328 V2.1.1:2016

Supplementary information: Notified body involved: N/A

Technical file held by: Giant Manufacturing CO., Ltd.

Korean Compliance (KC Mark)

KC

RECON + HL2600 P/N XXXXXXXXxxx 인증자 상호 GIANT MFG. CO., LTD.

기기의 명칭: Recon plus HL 2600 모델명: XXXXXXXXXX

제조자/제조국가: GIANT MFG. CO., LTD. / 대만 인증자 식별부호: Recon plus HL 2600

Taiwan NCC Compliance

產品名稱 (Product Name): Bicycle light

製造年份及製造號碼 (Year of Manufacture and Serial Number):

商品原產地 (Place of Origin): MADE IN CHINA

經銷廠商名稱 (Distributor Name): 捷安特股份有限公司 (Giant Manufacturing Co., Ltd.)

地址 (Address): 台中市西屯區河南路2段117號

電話 (Phone): 886-4-35059666

NCC警語 (NCC Warning):

• (依據低功率電波輻射性電機管理辦法 第十二條)
• ※經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
• (第十四條)
• ※低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。
• -前項合法通信,指依電信法規定作業之無線電通信。
• -低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。