INSTALLATION Product Manual

Important Information & Safety

IMPORTANT INFORMATION! Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

AVOID SCRATCHES! To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.

IMPROVE EFFICIENCY! Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

ANTI-TOPPLE WARNING! Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

IMPORTANT! It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months to assure stability throughout the lifespan of the product.

Maintenance and Cleaning: For the frame, use a rag dipped in neutral detergent, wipe fully, and then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.

Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.

Tools and Parts List

Please prepare the following tools:

• Screwdriver (Phillips head) ?
• Drill ⚡
• Hammer (for wall attachment, if needed) ?

When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

Assembly Steps

ASSEMBLED BY 2 ADULTS

WARNING: Children have died from furniture tipover. To reduce the risk of furniture tipover:

• ALWAYS install Anti-tip device provided.
• NEVER put a TV on this product.
• NEVER allow children to stand, climb or hang on drawers, doors, or shelves.
• NEVER open more than one drawer at a time.
• Place heaviest items in the lowest drawers.

This is a permanent label. Do not remove! ?️

Step 1

Parts Used: A x 12, B x 12, H x 12

Insert quickfit screw(A) into corresponding holes in No.3 and No.8 plates with a screwdriver as shown.

Connect No.3 and No.8 plates with No.10 using wooden dowel(H), then turn cam lock(B) in No.10 plate clockwise to tighten.

Step 2

Parts Used: A x 6, C x 12, S x 3, W x 2

Insert quickfit screw(A) into corresponding holes in No.4 plate with a screwdriver. Fix part(S) with screw(C) as shown.

Insert quickfit screw(A) into corresponding holes in No.9 plate. Fix part(S) with screw(C) as shown.

Flip the plate, insert quickfit screw(A) into corresponding holes. Fix part(S) with screw(C) as shown. Fix slide rail(W) using screw(C) as shown.

Step 3

Parts Used: B x 4, H x 4

Connect No.4 and No.9 plates with No.10 using wooden dowel(H), then turn cam lock(B) in No.10 plate clockwise to tighten.

Step 4

Parts Used: A x 2, B x 4, C x 8, H x 4, X x 2, S x 1

Insert quickfit screw(A) into corresponding holes in No.8 plate.

Fix part(S) with screw(C) as shown. Fix slide rail(X) using screw(C) as shown.

Connect the two components with No.12 plate using wooden dowel(H), then turn cam lock(B) in No.12 plate clockwise to tighten.

Step 5

Parts Used: A x 8, B x 8, H x 8, G x 3, D x 2

Fix No.27 plate to No.1 using screw(G) as shown.

Insert quickfit screw(A) into corresponding holes in No.1 plate with a screwdriver.

Cover No.1 plate to the component using wooden dowel(H), then turn cam lock(B) in No.3,8,9,4 plates clockwise to tighten.

Step 6

Parts Used: A x 12, H x 8, L x 10

Fix No.15 leg support to No.2 plate using screw(L) first. Cover No.2 plate to the bottom of the component using wooden dowel(H), then fix with screw(L) as shown.

Insert quickfit screw(A) into corresponding holes in No.2 plate with a screwdriver.

Step 7

Parts Used: A x 8, B x 8, H x 8

Insert quickfit screw(A) into corresponding holes in No.16 leg with a screwdriver (x4).

Connect No.17 and No.18 plates with No.16 leg using wooden dowel(H), then turn cam lock(B) in No.17,18 plates clockwise to tighten.

Step 8

Parts Used: B x 12, L x 4, H x 8

Attach the base (No.2 plate) using wooden dowel(H), then turn cam lock(B) in No.17,18 plates clockwise to tighten.

Fix No.16 leg to No.2 plate with screw(L) as shown.

Step 9

Parts Used: E x 52, I x 1, K x 1

Place clothing rod (I&K) to corresponding position as shown.

Connect two No.5 plates with No.25 first.

Fix No.5, No.6 and No.7 back plates with screw(E) as shown.

Step 10: Door Hinges

Pay attention to the difference between the middle parts of the two types of door hinges:

• The SMALL curved door hinges (F) are used on the outermost door plates.
• The LARGE curved door hinges (Y) are used on the door panel in the middle of the cabinet.

Step 11

Parts Used: C x 8, N x 2, O x 2, Y x 4

Fix hinge(Y) to No.14 and No.11 plate with screw(C) as shown.

Fix knob(O) with screw(N) as shown.

Step 12

Parts Used: C x 16

Attach No.14 plate to No.8; No.11 plate to No.9 by fixing hinge(Y) with screw(C) as shown.

Step 13

Parts Used: C x 12, F x 6, N x 2, O x 2

Fix hinge(F) to No.13 and No.26 plate with screw(C) as shown.

Fix knob(O) with screw(N) as shown.

Step 14

Parts Used: C x 24

Attach No.13 plate to No.3; No.26 plate to No.4 by fixing hinge(F) with screw(C) as shown.

Step 15

Parts Used: A x 10, B x 10, L x 10

Insert quickfit screw(A) into No.19 plate with a screwdriver.

Attach No.22, No.23 and No.24 plates to No.19, then turn cam lock(B) clockwise to tighten.

Slide No.20 plate into grooves first, attach No.22 to No.21,23,24 plates, fix using screw(L).

Step 16

Parts Used: C x 12, O x 4, R x 4, U x 2, V x 2

Fix knob(O) to No.19 plate with screw(R) as shown.

Fix runner(V) and (U) to No.24 and No.23 plates respectively with screw(C) as shown.

Step 17: Drawer Installation

Align rails, slide the drawers.

Step 18: Hinge Adjustment

If there is misalignment after installation, adjust the screw to the best condition.

If doors are still not aligned correctly, please watch the video:

YouTube Video Guide ▶️

Step 19: Anti-Tipping Device Installation

Parts Used: J x 2, C x 2, P x 2, Q x 2

Install the anti-tipping device as shown.

[Diagram description: Shows attaching a bracket to the top of the cabinet, then securing it to the wall using screws and appropriate wall anchors.]

Warranty Information

WARRANTY CLAIMS

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
• Before making a claim, please call to inquire. Provide your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
• The product must be used in accordance with the instructions provided.
• For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Does not include damage during installation, but includes damage during transportation.

Scope of Responsibility

• The manufacturer shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
• After use, damage and scratches of the furniture are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas:

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns Policy

CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?

PLEASE FOLLOW THE BELOW INSTRUCTIONS:

• If you have purchased and simply changed your mind, follow the retailer's instructions for returns.

DEFECTIVE ITEMS

• If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call us first.

DAMAGED ITEMS

• If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused.
• If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
• In all circumstances, please save all packaging material and paperwork for the order.
• Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.