INSTALLATION

Important Information

Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

Assembly Tips

• Avoid Scratches: To avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
• Improve Efficiency: Find a partner to assist with installation to speed up the process and shorten the time.

Safety Warnings

Anti-Topple Warning

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, always use the provided anti-tip device. If not included, please purchase a wall attachment suitable for your wall. If unsure, seek professional advice. Read and follow each step carefully.

Important Maintenance Note

It is important to re-tighten all screws 2 weeks after assembly, and then every 3 months, to ensure stability throughout the product's lifespan.

For regular maintenance and cleaning: For the frame, use a rag dipped in neutral detergent, wipe thoroughly, and dry with a clean rag. For glass materials, wipe with a rag dampened with glass cleaner, and dry with a dry rag.

Do not use an electric screwdriver or excessive force during installation, as the boards can break easily.

Tools and Parts

Please prepare the following tools:

When installing, carefully confirm that each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

Assembly Instructions

WARNING: Furniture Tipover

Children have died from furniture tipover. To reduce the risk of furniture tipover:

• Always install the provided anti-tip device.
• Never place a TV on this product.
• Never allow children to stand, climb, or hang on drawers, doors, or shelves.
• Never open more than one drawer at a time.
• Place heaviest items in the lowest drawers.

This is a permanent label. Do not remove!

Assembly recommended by 2 adults.

Step 1

Screw eccentric rod (A) into board 2 using a screwdriver ?️. The diagram shows rod A being inserted into pre-drilled holes on board 2.

Step 2

Screw eccentric rod (A) into board 1 using a screwdriver ?️. The diagram shows rod A being inserted into pre-drilled holes on board 1.

Step 3

Screw eccentric rod (A) into board 3 using a screwdriver ?️. The diagram shows rod A being inserted into pre-drilled holes on board 3.

Step 4

Insert wooden dowel (B) into board 3. Attach board 4 to board 3. Add cam lock (C) into board 4 and turn clockwise ? to tighten, as shown.

Step 5

Tear off the back glue of the light strip (N). Fix light strip (N) to board 5 through part (P) using screw (Q) as shown. The diagram shows the light strip being prepared and then attached to board 5 using bracket P and screws Q.

Step 6

Tear off the back glue of the light strip (N). Fix light strip (N) to board 6 through part (P) using screw (Q) as shown. The diagram shows the light strip being prepared and then attached to board 6 using bracket P and screws Q (this step is repeated for two boards labeled 6).

Step 7

Insert wooden dowel (B) into board 2. Attach boards 5 and 6 to board 2. Add cam lock (C) into boards 5 and 6 and turn clockwise ? to tighten, as shown.

Step 8

Insert back board 7 along available grooves as shown. The diagram shows board 7 sliding into grooves on the back of the assembled structure.

Step 9

Insert wooden dowel (B) into board 1. Attach board 1 to boards 5 and 6. Add cam lock (C) into boards 5 and 6 and turn clockwise ? to tighten, as shown.

Step 10

Screw eccentric rod (A) into board 8 using a screwdriver ?️. The diagram shows rod A being inserted into pre-drilled holes on board 8.

Step 11

Tear off the back glue of the light strip (N). Fix light strip (N) to board 8 through part (P) using screw (Q) as shown. The diagram shows the light strip being prepared and then attached to board 8 using bracket P and screws Q.

Step 12

Insert back board 7 along available grooves as shown. The diagram shows board 7 sliding into grooves on the back of the assembled structure.

Step 13

Insert wooden dowel (B) into boards 1 and 2. Cover board 8 to the top. Add cam lock (C) to boards 1 and 2 and turn clockwise ? to tighten, as shown. This step secures the top panel (board 8) to the side panels (1 and 2).

Step 14

Fix part (G) to board 1 with screw (E) as shown. Connect the light strip (N) to the interface. The diagram shows part G being attached to the inside of board 1, and light strips being connected.

Step 15

Insert buckle (F) into back slots and fix with screw (E) as shown. This step secures the light strips or wiring using buckles (F) and screws (E) on the back panels.

Step 16

Fix hinge (H) to board 10 with screw (J) as shown. The diagram shows hinges being attached to the door panel (board 10).

Step 17

Assemble door 10 to board 1 and 2 by fixing hinge with screw (E) as shown. The diagram shows the door being attached to the main cabinet structure using the hinges.

Step 18

Install anti-tipping device as shown. This involves attaching part G to board 8, then securing with part M using screw L. The diagram shows a sequence: attach G to 8, then attach M to G using L, and then secure M to the wall.

Step 19

If doors are still not aligned correctly, please watch the video. If there is misalignment after installation, adjust the screw to the best condition. This step provides guidance on adjusting the door hinges.

Warranty

Warranty Claims

• There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
• Before making a claim, please call for assistance. Provide your purchase order number and details of the problem for a replacement part. A response will be arranged within 48 hours. If the part is out of stock, a shipping date will be provided.
• The product must be used in accordance with the instructions provided.
• For returns, the furniture must be cleaned and dried, and returned within 30 days of receipt.

Type of Warranty Claim

• Failure to follow the furniture instructions will invalidate the warranty.
• Damage during installation is not covered, but damage during transportation is.

Scope of Responsibility

• No responsibility will be borne for misuse or user damage and/or loss of parts during the installation of furniture.
• Damage and scratches after use are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas

• Sheet parts: 1 month from the date of purchase.
• Electrical parts: 1 month from the date of purchase.

Returns

Changed Your Mind and Need to Return Your Item?

Please Follow the Below Instructions:

• If you have purchased and simply changed your mind, follow the retailer's instructions for returns.

Defective Items

• If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call for assistance in the first instance.

Damaged Items

• If you receive an order with obvious shipping damage from the retailer, it is suggested that the delivery be refused. If the delivery has been accepted and shipping damage is found, please follow the specific instructions advised by the retailer.
• In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.