MFL22176 Double Sliding Door Rattan TV Cabinet Assembly Instructions
General Information & Cautions
CAUTION: When tightening screws, tighten sequentially. Do not tighten any screws fully and then move to the next one. When every part is correctly aligned, then tighten all screws.
PLEASE BE CAREFUL: Do not damage the hole position when you use power tools!
If any parts are missing, please contact customer support for a replacement. A one-month service is available for product replacements if damage is not caused by human error.
Estimated Assembly Time: 1.5 Hours
Parts List
- Part 1: Top Panel x1
- Part 2: Left Side Panel x1
- Part 3: Right Side Panel x1
- Part 4: Left Divider x1
- Part 5: Middle Shelf x1
- Part 6: Right Divider x1
- Part 7: Back Panel x1 (implied, not explicitly numbered in assembly but visible in diagrams)
- Part 8: Back Support Rail x2
- Part 9: Feet x4
- Part 10: Drawer/Door Runners/Rails x2
- Part 11: Feet Support Brackets x4
- Part 12: Support Brackets x2
- Part 13: Adjustable Foot Pads x2
- Part 14: Sliding Doors with Rattan Inserts x2
Hardware List
- Hardware A: Screw Ø6x35mm x20 (+1)
- Hardware B: Screw Ø15x10mm x20 (+1)
- Hardware C: Screw Ø6x30mm x28 (+2)
- Hardware D: Screw Ø4x35mm x16 (+1)
- Hardware E: Bracket x4
- Hardware F: Screw Ø6x35mm x4
- Hardware G: Screw Ø32(+2)
- Hardware H: Cam Lock x2
- Hardware I: Screw Ø4x35mm x8
- Hardware J: Screw Ø6x80mm x4
- Hardware K: Screw Ø10x10mm x4
- Hardware L: Screw x10 (size not specified)
- Hardware M: Screw Ø3x16mm x10
- Hardware N: Adjusting Foot Pad x2
- Hardware O: Decorative Cap x4
- Hardware P: Screw Ø3x16mm x4
Assembly Steps
Step 1
Attach Part 5 (Middle Shelf) to Part 1 (Top Panel) using Hardware A (Ø6x35mm) and Part C (Ø6x30mm). Attach Part 1 to Part 2 (Left Side Panel) and Part 3 (Right Side Panel) using Hardware A and C.
Diagram shows attaching the middle shelf and side panels to the top panel.
Step 2
Attach Part 4 (Left Divider) and Part 6 (Right Divider) to Part 5 (Middle Shelf) using Hardware C (Ø6x30mm). Attach Part 4 and Part 6 to Part 1 (Top Panel) using Hardware C and D (Ø4x35mm). Note: These parts may not have edge banding.
Diagram shows attaching the internal dividers to the top panel and middle shelf, with a 90° angle indicator for alignment.
Step 3
Attach Part 1 (Top Panel) to Part 6 (Right Divider) using Hardware B (Ø15x10mm). Note: This part may not have edge banding.
Diagram shows attaching the top panel to the right divider with cam locks and screws.
Step 4
Assemble the main cabinet structure by attaching Part 1 (Top Panel), Part 2 (Left Side Panel), Part 4 (Left Divider), Part 5 (Middle Shelf), and Part 6 (Right Divider) using Hardware B (Ø15x10mm) and C (Ø6x30mm).
Diagram shows the main cabinet frame assembly using various screws and cam locks.
Step 5
Insert the main structural components: Part 1 (Top Panel), Part 2 (Left Side Panel), Part 3 (Bottom Panel), Part 4 (Left Divider), Part 5 (Middle Shelf), and Part 6 (Right Divider) into their designated positions, indicated by arrows.
Diagram shows the insertion of the main panels and shelves into the cabinet structure.
Step 6
Attach Part 8 (Back Support Rail) to the rear of the cabinet structure using Hardware D (Ø4x35mm).
Diagram shows attaching a horizontal support rail to the back of the cabinet.
Step 7
Attach Part 8 (Back Support Rail) to the main cabinet structure using Hardware D (Ø4x35mm). The diagram indicates a 90° rotation for proper alignment.
Diagram shows attaching another back support rail, with a 90° alignment indicator.
Step 8
Attach vertical supports (Part 8) to the top panel using Hardware A (Ø6x35mm).
Diagram shows attaching vertical supports to the top surface of the cabinet.
Step 9
Attach feet (Part 9) to the bottom of the cabinet structure using Hardware A (Ø6x35mm).
Diagram shows attaching the feet to the underside of the cabinet.
Step 10
Attach feet assemblies (Part 9) to the cabinet structure using Hardware B (Ø15x10mm).
Diagram shows connecting the feet to the cabinet using cam locks and screws.
Step 11
Attach rails (Part 10) to the feet assemblies (Part 9) using Hardware J (Ø6x80mm) and K (Ø10x10mm).
Diagram shows attaching drawer or door runners to the feet assembly.
Step 12
Connect the assembled feet/rail structure to the main cabinet body using Hardware B (Ø15x10mm) and C (Ø6x30mm).
Diagram shows the final connection of the base structure to the main cabinet.
Step 13
Attach horizontal supports (Part 10) and feet (Part 12) to the cabinet using Hardware I (Ø6x30mm) and P (Ø3x16mm).
Diagram shows attaching additional supports and feet to the cabinet.
Step 14
Attach adjustable foot pads (N) to the bottom of the cabinet and decorative caps (O) using Hardware N (Ø3x16mm).
Diagram shows attaching adjustable feet and decorative caps.
Step 15
Attach sliding door runners/brackets (Part 14) to the cabinet structure using Hardware E (Bracket), F (Ø6x35mm), and G (Screw Ø32(+2)).
Diagram shows attaching the sliding door mechanisms to the cabinet frame.
Step 16
Attach more sliding door runners/brackets (Part 14) to the cabinet structure using Hardware E (Bracket) and F (Ø6x35mm).
Diagram shows attaching additional sliding door mechanisms.
Step 17
Insert the sliding doors (Part 14) into the attached runners. The diagram illustrates the alignment and sliding motion.
Diagram shows how to insert the sliding doors into the runners.
Step 18
Attach back panel supports using Hardware L (Ø6x80mm) and M (Ø3x16mm).
Diagram shows attaching supports to the back panel area.
Step 19
Attach adjusting foot pads (N) to Part 13. If the TV cabinet is unstable on the ground, rotate the Part 13 adjusting foot pad (N) to level it.
Diagram shows attaching adjustable foot pads and text explaining their function for leveling.
