Parts List
Before assembling the playard, check that you have all the parts for this model:
- Playard (fully assembled) x 1
- Canopy with toys x 1
- Mattress x 1
- Bassinet x 1
- Metal Support Tubes (2 male, 2 female)
- Travel / Storage Bag x 1
- Changing Table x 1
- Long Curved Bar x 2
- Short Bar with Connector Knob x 2
- Parent Organizer x 1
- Hook x 2
- Music Center x 1
Note: This unit is not equipped with any mobile (Wind up or Fixed).
Note: *Toys and mobile may vary.
Important Information
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
Customer Service
For assistance, contact Baby Trend Customer Service at 1-800-328-7363 between 8:00 A.M. and 4:30 P.M. Pacific Standard Time. Please have your model number and manufacturing date available. This information can be found on a small sticker under the playard.
Contact by mail: Baby Trend, Inc., 1607 S. Campus Ave., Ontario, CA 91761
Contact online: http://www.babytrend.com
Safety Warnings
General Warnings
- WARNING: NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN. Infant may roll into space between pad and loose mesh side causing suffocation.
- WARNING: Infants can suffocate:
- In gaps between a mattress too small or too thick and product sides
- On soft bedding
- Never add a mattress, pillow, comforter, or padding.
- Use only the mattress provided by manufacturer.
- Never use a water mattress with this product.
- WARNING: See playard floor and side rails for warnings.
- WARNING: Failure to follow these warnings and the instructions could result in serious injury or death.
- The playard, including side rails, must be fully erected prior to use. Make sure latches are secure.
- Strings can cause strangulation! NEVER place items with a string around a child's neck such as hood strings or pacifier cords. NEVER suspend strings over playard or attach strings to toys.
- Discontinue use of the product when child is able to climb out or has reached the height of 35 in. (890 mm) or weight of 30 lbs. (14 kgs), whichever comes first.
- When child is able to pull to standing position, remove bumper pads, large toys and other objects that could serve as steps for climbing out.
- NEVER place product near a window where cords from blinds or drapes can strangle a child.
- Always provide the supervision necessary for the continued safety of your child. When used for playing, NEVER leave child unattended.
- To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.
- NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service for replacement parts, repair or instructions. NEVER substitute parts.
- NEVER leave child in product with sides lowered. Be sure sides are in raised and locked position whenever child is in product.
- NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation.
- This product is not intended for commercial use.
Maintenance and Cleaning Instructions
- Use only household mild soap and warm water.
- DO NOT USE BLEACH.
- DO NOT MACHINE WASH.
Assembly Instructions
IMPORTANT: To ensure safe operation of your playard, please follow these instructions carefully. Please keep these instructions for future reference.
IMPORTANT: Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. NEVER use if any parts are missing or broken.
IMPORTANT: Adult assembly is required.
To Assemble Playard
Step 1: Prepare Playard Frame
Unzip the storage bag and remove the Playard frame. Undo the three (3) fastening straps and set the Mattress aside. (As shown in Figures 1 and 2).
Step 2: Position Frame
Turn the Playard upside down.
Step 3: Attach Legs
Attach the Legs to the Playard by pushing each Leg into the bottom of the leg mount until both sides snap firmly into place (Figure 3). IMPORTANT: Check that each Leg is securely attached before use.
Step 4: Attach Wheels
Attach the Wheels to the Playard using the axles, retainers, and caps provided. Align each Wheel and insert the axle through the center (Figure 4). Secure by pushing the retainer over the end of the axle until it snaps into place (Figure 5). Finish by pushing the cap over the end of the axle and retainer until it snaps into place (Figure 5). IMPORTANT: Check that each Wheel is securely attached before use.
Note on Brakes: To operate the brakes on the Wheels, press downward on the brake levers. To release, lift upward on the lever (Figure 6).
Step 5: Lock Top Rails
Turn the Playard right side up. Keep the Legs and Wheels close together. Stretch out the top of the Playard and pull up one side at a time of each of the top rails until each latch "Clicks" and locks securely into place (Figure 7). Note: The best way to lock the rail(s) is to hold one hand on each side and pull up sharply. Do not pull from the middle where the latch release is located.
IMPORTANT: The handle located in the center of the Playard floor MUST remain raised (approximately 45.7 cm or 18 inches) while locking the side rails in place. If the center is not raised, the rails will NOT lock.
If you experience difficulty and one side of the rail will lock but the other side will not, unlock the rail by squeezing the release in the center and try again. If difficulty persists, contact Customer Service.
Step 6: Lock Center Handle
Once all four (4) top rails are locked in place, push down on the center handle (Figure 8). The center mechanism will rotate clockwise 90 degrees and automatically lock in place. IMPORTANT: Test each top rail by pushing down slightly to confirm each is rigid and locked securely in place before use (Figure 9).
Step 7: Place Mattress
Place the Mattress on the floor of the Playard with the padded side facing up (Figure 10).
Step 8: Secure Mattress
Feed the three (3) hook and loop straps located on the underside of the Mattress through the slots in the floor of each end of the Playard (Figure 11). Fasten the hook and loop straps to the underside of the Playard floor to prevent the Mattress from moving (Figure 12).
Folding Playard
Step 1: Release Mattress Straps
Undo the three (3) hook and loop straps holding the Mattress from underneath the Playard floor, or remove the Mattress for the Bassinet and set it aside.
Step 2: Lower Center Handle
Grasp the center handle, push down, and rotate the handle counter-clockwise 90 degrees and lift upward until the handle is as high as the top rails (Figure 13). Gather the Legs and Wheels together towards the center as close as possible so that they nearly touch (Figure 14). Note: The top rails of the Playard are still in the "Locked" position.
Step 3: Release Top Rails
Locate the rail release lever in the center and bottom side of each rail. Lift slightly while squeezing the lever until the rail "Clicks" and releases. Push down each side of the rail while still holding the release lever until both sides are down. Repeat for all remaining sides (Figure 15). Note: If the top rail(s) do not release completely, DO NOT FORCE! Check the floor of the Playard to make sure all the bottom rails are unlocked and the middle handle is pulled up and has not fallen back down. If so, repeat step #3.
Step 4: Gather Frame
Gather the four (4) corners and center them together tightly (Figure 16).
Step 5: Wrap Mattress
Wrap the Mattress around the Playard frame with the padded side facing inward.
Step 6: Secure Mattress
Secure the three (3) hook and loop straps by feeding them through the loops on the end of the Mattress and folding them back onto themselves (Figure 17).
Step 7: Place in Bag
Place the folded Playard into the carry bag so that the handle comes through the opening between each side of the zipper.
To Assemble Bassinet
Step 1: Position Bassinet
Position the Bassinet over and down into the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place (Figure 18).
Step 2: Assemble Mattress Support Tubes (If Equipped)
Assemble Mattress Support Tubes by inserting the two (2) male tubes into the two (2) female tubes (Figure 19).
Step 3: Insert Support Tubes
Insert both assembled Mattress Support Tubes into the loops provided on the bottom of the Bassinet (Figure 20).
Step 4: Place Mattress
Place the Mattress into the Bassinet with the padded side facing upward (Figure 21). Note: Fasten tabs underneath the Mattress to secure it in place.
To Remove Bassinet
- Remove Mattress from Bassinet.
- Remove Canopy.
- Unsnap all clips and lift Bassinet.
To Assemble Canopy
Step 1: Prepare Canopy
If the equipped Canopy comes in "U" shape (Figure 22), you need to assemble the Canopy before attaching it to the playard. If the Canopy comes in "C" shape, skip to step 3. Open Canopy as seen in Figure 23. Make opening adjustments at the top of the Canopy by aligning the inner center strap with the two outer straps (Figure 24).
Step 2: Align and Attach Canopy
Open Canopy completely and ensure the straps are aligned correctly so the Canopy fits on the Playard (Figure 25). Position Canopy in the center of the Playard. Attach each side of the Canopy by firmly pressing the Canopy clips onto the center of the top rails as close to the center as possible (Figure 26). Attach the other end of the Canopy to the Playard by snapping the two (2) buttons or velcro located near each corner of the Playard (Figure 27). Note: Your canopy may come with plush toys if your unit does not include a mobile.
To Remove Canopy
Unsnap the Canopy and pull upward on the ends of the Canopy from the side of the Playard.
Mobile Assembly (Wind Up or Fixed)
Important Mobile Safety Notes
- DO NOT attach Mobile to Canopy until Canopy is correctly installed.
- A crib mobile is intended for visual stimulation and is not intended to be grasped by the child.
- If attached to the crib or playpen, remove when baby begins to push up on hands and knees.
- If designed for wall/ceiling mounting, ensure it is clearly out of a standing baby's reach.
- Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or playpen according to the instructions. Check frequently.
- DO NOT add additional strings and straps to attach to a crib or playpen.
- DO NOT attach the Mobile with child in Playard or Bassinet.
- DO NOT remove the Mobile before retracting the Canopy or removing the Canopy.
Wind Up Mobile Assembly
Contents: (a) 1 Wind Up Mobile, (b) 1 Mobile Tri-shaped Arm (toys may vary).
1. Attach the Mobile (a) to the Tri-shaped Arm (b) by aligning slots on both pieces then gently pressing the two pieces together (Figure 28).
2. Attach the Mobile to Canopy using the Velcro and connecting the straps together through the hole in the top of the Mobile housing (Figure 29).
Fixed Mobile Assembly
Contents: (a) 1 Mobile Lower Arm, (b) 1 Mobile Arm Holder, (c) 1 Mobile Upper Curved Arm, (d) 1 Mobile Tri-shaped Arm, (e) 3 Toys (toys may vary).
1. Insert the Mobile Lower Arm (a) into the Mobile Arm Holder (b) until locked together (Figure 30).
2. Insert the Mobile Upper Curved Arm (c) into the Mobile Lower Arm (a, b) until locked together (Figure 31).
3. Snap the Mobile Tri-shaped Arm (d) onto the end of the Upper Curved Arm (a, b, c) (Figure 32). Connect each of the three Toys (e) to the Mobile by threading the string into the slot at the end of each arm.
4. Insert the bottom of the Mobile Arm into the frame of the Playard (Figure 33).
To Assemble Changing Table
WARNING: FALL HAZARD
To prevent death or serious injury, always keep child within arm's reach. Always use restraint belt to prevent falls, see page 15 for details.
Contents: (a) 2 Long Curved Bars, (b) 2 Short Bar with Connector Knobs, (c) 1 Changing Table.
ATTENTION: Playard must be fully assembled and securely locked before installing or using the changing table feature. (See To Assemble Playard section).
Step 1: Connect Long Bars
Connect the two (2) Long Curved Bars together (Figure 34).
Step 2: Insert Bars into Fabric
Insert the assembled curved bars into the Changing Table fabric (Figure 35). Slide the Curved Bars around inside the sleeve of the Changing Table.
Step 3: Connect Short Bars
Connect the two (2) Short Bars to each end of the Long Curved Bar (Figure 36). Make sure that the knobs are both facing down and in the same direction on each end (Figure 37).
Step 4: Attach to Playard
Insert Connector Knob Prongs into holes located on both corners of the Playard (Figure 38).
Step 5: Lock Knobs
Turn the Connector Knobs counter clockwise to lock into place (Figure 39).
Step 6: Position Table
Flip Changing Table over onto Playard (Figure 40).
Step 7: Secure Table
Snap the two (2) buttons on the flap down onto the Playard (Figure 41).
IMPORTANT: Check that the Changing Table is correctly and securely installed BEFORE each use.
Changing Table Restraint System Use
1. Place child on changing table, ensuring hands and arms are clear of the restraint. Bring the restraint around the child's waist and clip the male and female ends of the buckle together (Figure 42).
2. Tighten strap until it fits snug around the child's waist. DO NOT OVER TIGHTEN (Figure 43).
3. To remove, unsnap the buckle.
ATTENTION: NEVER use changing table if it is damaged or broken.
To Remove Changing Table
Flip Changing Table to the outside of the Playard. Unsnap the fabric flap of the Changing Table from the Playard. Twist Connector Knobs clockwise to unlock (Figure 44). Remove the Changing Table from the Playard (Figure 45) and disconnect the Short Bars from the Curved Bar by pressing on the snap buttons and pulling apart. Remove the Curved Bar from the Changing Table sleeve.
Parent Organizer Assembly
Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it snaps into place (Figure 46).
Diaper Stacker: Skip to step 2.
Connect the Parent Organizer/Diaper Stacker to the Playard by sliding the two (2) connecting clips over an open portion of the top rail of the Playard (Figure 47). Note: The Parent Organizer/Diaper Stacker can only be installed on open sides of the Playard where the connecting clips can easily be attached without interfering with other features.
Music Center
WARNING: Battery Safety
Keep batteries out of children's reach. Old and new batteries should not be mixed. Alkaline, standard carbon-zinc, and rechargeable nickel-cadmium batteries should not be mixed. Remove batteries before storing the music center for a long period of time.
Attachment
The Music Center is designed to be attached to the playard corners. It can be attached on the Changing Table's side or the Canopy's side (See Figure 50).
Music Operation
The Music Center requires 4 AA batteries. Please see Figure 51 for battery installation. Unscrew the battery door screws and pull outward on the battery door. Install batteries as shown. Re-install battery door and secure with screws.
- To activate the unit, press the ON/OFF button. Press the button a second time to switch the unit off.
- To listen to SLEEP music, press the SLEEP button. Use the previous/next button to change the song. The Vol +/- buttons control the unit's volume.
- To listen to PLAY music, press the PLAY button. Use the previous/next button to change the song. The Vol +/- buttons control the unit's volume.
- To listen to NATURE sounds, press the NATURE button. Use the previous/next button to change the sound. The Vol +/- buttons control the unit's volume.
- VIBRATION: To use the vibration button, press down once to activate the speed, press again for a Medium speed, and once more for the faster speed. Press to reduce the speed.
- NIGHT LIGHT: To use the night light, press the [night-light-button]. The light has 3 settings of brightness and is controlled by the [brightness-button].
- VOICE RECORDER: To use the Voice record function, press the [record-button] and speak into the microphone to record your 10-second voice message. Press the [play-button] to hear the message.
- VOICE ACTIVATION: To use the Voice Activation function, press the [voice-activation-button] twice if the unit is powered off. If the unit is already powered on, press the button once. The voice activation light will be illuminated when in voice activation mode. If your infant cries, their voice will activate the sleep music to come on and play. When voice activation is enabled, sleep mode is active for 2 hours.
- MP3 FUNCTION: Use the input jack to attach your MP3 player to the unit. Press the [mp3-input-button] to select the MP3 input. Your MP3 music will then be played through the unit and will override the unit's music. To listen to the unit's music, depress the [play-button]. Volume will be controlled by the MP3 player.
