ℹ️ Document Conversion Notice:
This document has been converted from PDF and formatted to fit this screen. Diagrams and images may be available only in the original here.
WYBOT Robotic Pool Cleaner User Manual
Models: WYBOT C2 Vision & WYBOT C2
Read through the entire manual before running your new robotic pool cleaner, and keep this manual handy for your reference.
Introduction
Thank you for choosing WYBOT products. WYBOTICS Co., Ltd. is dedicated to providing the best solutions for pool cleaning, allowing users to enjoy their family time.
The WYBOT Robotic Pool Cleaner offers high efficiency, low power consumption, easy operation, and thorough pool cleaning. Its unique design and reliable functions include one-button activation, powerful suction and scrubbing, fine filtration, smart navigation, and remote control. It is highly compatible with various pool shapes and construction materials, ensuring convenient, intelligent, and optimal pool cleaning.
For any questions, users can contact WYBOTICS Co., Ltd. via email or visit their website. WYBOTICS Co., Ltd. welcomes advice for continuous improvement.
Safety Instructions
Warning
Read the manual carefully before using the cleaner. User safety is paramount. Operate the device as per instructions; WYBOTICS Co., Ltd. is not held liable for any loss or injury caused by improper use.
Failure to operate the device as per the warnings can result in serious injury, electrocution, or death.
Use only accessories recommended or sold by WYBOTICS Co., Ltd.
Use only the original and authorized charger. Avoid charging other types of devices with this charger. Improper use may result in overheating or corrosive liquid leakage from the battery.
Power off the robot when performing any maintenance or removing it from the pool.
Ensure the charging port is dry before plugging in the charger.
Make sure the electrical outlet is protected by a ground fault circuit interrupter (GFCI) and an earth leakage interrupter (ELI).
Do not use a cord-damaged charger to avoid electrical shock.
Do not use unauthorized extension cords to connect the charger to the robot.
Never allow children to ride on the cleaner/docking station or play with it as a toy.
Do not allow children to operate or maintain the device or docking station.
Do not enter the pool when the robot is working.
Never expose or charge the device in flammable environments.
Only licensed professionals can disassemble the sealed parts of the robot.
Cautions
Failure to operate the device as per the cautions can cause damage to the device.
Charge the unit before first use.
Do not overcharge the cleaner, which will reduce battery life.
Charge the cleaner prior to being stored for a long time (over 6 months) to maintain optimal battery life.
Do not operate the cleaner while the pool filter is running.
Remember to wash and clean the filter basket and ultra-fine filter after each use.
Store the cleaner in a cool and ventilated place, away from direct sunshine or any heat source.
Use the pool cleaner only in the following water conditions:
Parameter
Value
Chlorine
Max 4 mg/L
pH
7.0 - 7.8
Temperature
41-95 °F (5-35 °C)
NaCl
Maximum 5000 PPM
WYBOT At A Glance
Product External Overview
The WYBOT Robotic Pool Cleaner features several key external components:
Handle: Used to remove and transport the device.
LED Indicator: Displays different light colors to indicate device status.
On/off Button: Used to turn the device on or off.
Pump: Pumps out water through a window.
Charging Port: Connects the charger to the cleaner.
Track: Enhances the device's capability in climbing walls and various obstacles.
Scrubbing Brush: Knocks loose dirt and rolls it into the device.
Camera (WYBOT C2 Vision only): Vision technology for high-efficiency cleaning.
Product Internal Overview
The internal components include:
Lid Open Button: Used to open the cover and access the filters.
Water Outlet: Allows quick release of water.
Ultra-fine Filter: An auxiliary filter that traps fine dirty particles on the floor. Recommended for 'turbo floor mode' only. Do not install if the floor is heavily soiled, as it may affect cleaner operation.
Filter Basket: Stores collected dirt and debris. Remember to install it before cleaning and wash it after each use.
Packing List
The package includes:
Device x 1 (WYBOT C2 or C2 Vision)
Filters x 2 (one ultra-fine filter, one filter basket)
Quick Start Guide x 1
User Manual x 1
Charger x 1
Floating Blocks (quantity not specified, but shown as two blocks)
Get Started
Charge Your New WYBOT
The device has a lithium-ion rechargeable battery. Charge the battery before first use and when the battery is low. Connect the device to a power outlet using the included cable and adapter.
A diagram shows the cleaner connected to a charger, with an LED indicator on the cleaner showing a green light, indicating 'Fully Charged!'.
Note:
When charging, ensure the device is at least 3m (approximately 10ft) away from the edge of the pool.
To reduce fire risk, keep the device and adapter away from direct sunshine or water when charging.
For important safety, double-check that the device is powered off and the charging port is dry before charging.
The best charging environment temperature is 32°F - 95°F (0°C - 35°C), with relative humidity (RH) at 5%-95%.
The adapter has a blue light indicator, which displays the power supply status. The LED indicators on the top of the cleaner turn solid green when fully charged.
The LED lights indicate different device statuses:
LED Light
Indication
Status
?
Solid
Power On
?
Flashing
Under working
?
Solid
Connecting to App
?
Flashing
Low battery or under self-parking in the pool
?
Flashing
Charging in progress
?
Solid
Fully charged
?
Solid or flashing
Fault
Setup Your New WYBOT
Turn on the device by pressing the on/off button. The LED indicator on top will display a solid green light to show the current battery level, then a solid blue light when the device is on. If the battery level is too low to start cleaning, the LED lights will show a flashing yellow light, indicating 'Low battery!'.
Note:
When the yellow light flashes, charge the device immediately.
If the red LED light is on, refer to the troubleshooting section in this manual or contact customer service.
Connect to Your App
Download the WYBOT App to your smart mobile device by scanning the QR code or searching on Google Play or the App Store.
iOS
Android
iOS 15.0 or later
Android 8.0 or later
Choose Your Cleaning Mode
You can choose a cleaning mode for your cleaner through the app after connecting to your App.
Modify cleaning modes via the App when the cleaner is out of the pool. The default mode is 'Wall then floor'.
If the device restarts, it will automatically enter the cleaning mode set last time.
Run Your New WYBOT
Hold the handle of the robot and put it into the pool vertically.
Let it sink down to the floor to empty trapped air inside.
Note:
To achieve optimal cleaning performance, ensure the water depth of the pool is at least 19.5 inches (50 cm) high from the top of the device.
After about 20 seconds of self-calibration, the indicator light will turn to a flashing blue. The cleaner is ready to clean.
The cleaner begins to clean walls, floor, and waterline as default or as set through the App.
Dirt Hunting Mode (Special for WYBOT C2 Vision)
If the dirt hunting cleaning mode is chosen through the APP, the cleaner will start cleaning the floor in a high-efficiency cleaning path after entering the pool.
During cleaning, the camera on the front of the cleaner will automatically detect and target dirt when recognized. The robot needs to enrich its recognition of dirt from the start and may turn on and record floor dirt types during cleaning. It will reach its best targeted cleaning performance after one month of cleaning.
WYBOT continues enhancing its capability. Users are encouraged to update the device for the best cleaning experience.
Note:
The camera on the front is protected by a film when out of the factory; peel it off before running 'Dirt-hunting mode'.
The camera on the robot will only be turned on when underwater.
The dirt hunting cleaning mode is performed based on vision, so the camera must be kept free from any dust or scratches, as they may decrease its performance.
The device will automatically move to stop by the edge of the wall when finishing cleaning or when the battery is low.
Insert the included hook into a pool pole and lift the cleaner out of the pool.
Take the cleaner out of the pool vertically to quickly drain internal water.
Do a Filter Cleaning
Push the lid open button up to open the cover.
Take out the filter basket and ultra-fine filter.
Empty all debris and rinse with clean water.
After rinsing, put the filter basket and ultra-fine filter back into the cleaner and close the cover.
Note:
As electric components are inside the cleaner, store the cleaner in a cool and ventilated place, away from direct sunshine or any heat source.
Charge the cleaner prior to being stored for a long time (over 6 months) to maintain optimal battery life.
Device Specification
Model
WYBOT C2
WYBOT C2 Vision
Pool Size
150m²
150m²~180m²
Min Water Depth
9.8ft (3m)
9.8ft (3m)
Device Dimension
360(L)*360(W)*240(H) mm
360(L)*360(W)*240(H) mm
Weight
8kg
8kg
Runtime
3 hours (Eco Floor)
3 hours (Eco Floor)
Charging Time
3 hours
3 hours
Power
65W
65W
Charger Input
100-240V, 50-60Hz
100-240V, 50-60Hz
Charger Output
25.2V/1.5A
25.2V/1.5A
Battery Capacity
4600mAh
4600mAh
Filtration
180µm+Ultra-fine filter
180µm+Ultra-fine filter
Moving Speed
10m/min
10m/min
Water Resistance
IPX8
IPX8
OTA upgrading
Available
Available
App Connection
Available
Available
Limited Warranty
All WYBOT pool cleaners have been inspected and licensed to be sold as per local laws.
The warranty applies only to original buyers and is not valid for resale or any other transfers.
Any damages to the unit caused by improper use, unauthorized repair, or disassembly are not covered by WYBOTICS Co., Ltd.'s warranty.
The order number or record must be presented for any claim or repair within the warranty period.
Scan the QR code for the warranty policy: [QR code symbol]
How to Maintain Your Device
Follow these steps to store your cleaner and maintain good performance:
Ensure the device is powered off.
Dry out the cleaner and filter drawer.
Fully charge the battery.
Store the cleaner in a cool and ventilated place, away from direct sunshine, heat sources, frost, and squeezing, with an ambient temperature between 5°C/41°F and 45°C/113°F.
Charge the cleaner every three months to ensure optimal battery life.
Note:
If the device does not work after a long-term low battery life or being off, contact the after-sale team for help. For safety, do not attempt to disassemble it without authorization.
FAQ & Troubleshooting
Q: What pool shapes and construction materials is the cleaner suitable for?
A: The machine can be applied to rectangle, oval, or irregular shapes of in-ground swimming pools. Applicable construction materials include PVC, gunite, tile, and other materials. Slippery materials such as tiles, mosaics, and acrylic may not work well, and may require modification.
Q: Will obstacles such as steps, shallow water areas, drains, slopes etc. in the swimming pool affect the running?
A: The machine can climb steps, drains, and shallow water areas. These obstacles may influence its cleaning path but will not affect the operation of the machine.
If you encounter the following situations when using the cleaner, you can check the table and solve them yourself.
No.
Issues
Details
Possible Causes
Suggested Solution
1
Device does not work
A solid red light
Impeller is stuck
Check the impeller and clean foreign objects.
A flashing red light
Motor protection
Restart.
A flashing red light
Not put the device into the water or the pool water is too shallow
Restart and put it into the pool immediately. Ensure water depth is over 0.5m.
A breathing yellow light
Battery low
Fully charge the device and restart.
2
Unable to charge
Charger light flashes
Poor contact
Re-plug the charger.
3
Do not climb walls
Slippery construction materials
Stick adhesive blocks (Contact after-sale team for instruction).
Too dirty water
Clean the filter basket.
4
Abnormal wall climbing
Climbing slowly
Filter basket blocked
Clean the filter basket.
Sinking down away from wall or floating on the water
Intake air
Stick adhesive blocks (Contact after-sale team for instruction).
Filter basket blocked
Clean the filter basket.
5
Only clean part area and cannot clean the entire pool
Wrong cleaning mode
Connect to the App and re-choose a suitable cleaning mode.
Firmware not latest
Connect to the App and update the firmware.
6
Front side up when on the floor
Filter basket blocked
Clean the filter basket.
7
Do not clean as set cleaning path
Encounter Obstacles
Clean the filter basket.
Stuck at water drains
Drain height is over 3cm
Help the machine away from the obstacle.
Unable to connect to the App
Device power off
Restart.
8
The APP cannot be connected when the device is in the pool
Not available
Connect the device on the shore.
Note:
If you cannot find a solution from the table, contact the after-sale team.
Certification
WYBOT robotic pool cleaners have passed all performance and reliability tests and obtained relevant certifications from the countries in which they are sold, ensuring product quality.
Certifications include: CE, FCC, RoHS, ETL Listed US (Intertek).
WYBOT Customer Care
Due to continuous product improvement, the products in this manual are subject to the real products, and WYBOTICS Co., Ltd. reserves the right to update products.
If you encounter any problems during use, contact the after-sale team. For more details, visit the WYBOTICS website: www.wybotpool.com
WYBOT C2 & C2 Vision Robotic Pool Cleaner User Manual Comprehensive user manual for the WYBOT C2 and C2 Vision robotic pool cleaners, covering setup, operation, maintenance, troubleshooting, and safety guidelines. Learn how to use your pool robot effectively.
WYBOT C2 Intelligent Cordless Pool Robot User Manual Comprehensive user manual for the WYBOT C2 intelligent cordless pool robot. Covers setup, operation, maintenance, troubleshooting, and specifications for efficient pool cleaning with 180 minutes of runtime.
WYBOT Robotic Pool Cleaner User Manual: C2 & C2 Vision Comprehensive user manual for WYBOT Robotic Pool Cleaners, models C2 and C2 Vision. Covers setup, operation, maintenance, safety, and troubleshooting for efficient pool cleaning. Learn how WYBOTICS Co., Ltd. helps you enjoy your pool.
WYBOT Robotic Pool Cleaner User Manual - C2 & C2 Vision Discover the WYBOT Robotic Pool Cleaner User Manual for models C2 and C2 Vision. This guide provides comprehensive instructions for setup, operation, maintenance, and troubleshooting, ensuring efficient and intelligent pool cleaning. Learn about features like smart navigation, powerful suction, and fine filtration for a pristine pool.
WYBOT Robotic Pool Cleaner User Manual: C2 & C2 Vision Models Comprehensive user manual for WYBOT C2 and C2 Vision robotic pool cleaners, covering setup, operation, maintenance, safety, troubleshooting, and specifications. Learn how to get the most out of your pool cleaning experience.
