WYBOT C2 Intelligent Cordless Pool Robot

Welcome and Safety Information

Thank you for choosing the WYBOT C2 Intelligent Cordless Pool Robot. This manual provides essential information for the safe and effective operation of your new pool cleaning device.

⚠️ IMPORTANT SAFETY INSTRUCTIONS ⚠️

Please read and follow all instructions before operating the pool robot. Failure to do so may result in personal injury or damage to the product.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure they do not play with the appliance.
• Only use the charger supplied with the unit.
• Do not operate the robot if the power cord or charger is damaged.
• Ensure the robot is fully charged before first use.
• Do not operate the robot in water temperatures outside the specified range (typically 10°C - 35°C or 50°F - 95°F).
• Do not operate the robot if the pool water level is too low, exposing the motor.
• The robot is designed for cleaning pool surfaces only. Do not use it for other purposes.
• Always disconnect the charger before cleaning or maintenance.
• Keep the charging contacts clean and dry.

Product Components

Your WYBOT C2 package includes the following:

• Pool Robot Unit: The main cleaning device.
• Filter Basket: Located inside the robot, collects debris. It typically consists of a fine mesh to capture small particles.
• Power Adapter: Used to charge the robot.
• Charging Cable: Connects the power adapter to the robot.
• User Manual: This document.
• (Optional) Hook: May be included for retrieving the robot from the pool.

[Diagram showing all components with labels would be here. It depicts the robot, its filter compartment, charging port, power adapter, and cable.]

Setup and Charging

Proper charging ensures optimal performance.

Charging the Robot

1. Ensure the robot is switched OFF.
2. Connect the charging cable to the robot's charging port. [Icon: Charging port symbol]
3. Connect the other end of the charging cable to the power adapter.
4. Plug the power adapter into a suitable electrical outlet.
5. The charging indicator light on the robot will illuminate (e.g., red while charging, green when fully charged).
6. Allow the robot to charge fully before its first use (approximately 4-6 hours).
7. Once charging is complete, disconnect the power adapter from the outlet and then disconnect the charging cable from the robot.

[Note: Keep charging contacts clean and dry. Avoid overcharging.]

Operation

Follow these steps to operate your WYBOT C2 robot.

Placing the Robot in the Pool

1. Ensure the robot is charged and switched OFF.
2. Gently place the robot into the pool, allowing it to fill with water and sink to the bottom. Ensure it is oriented correctly.
3. Do not throw the robot into the pool, as this may cause damage.

Starting the Cleaning Cycle

1. Once the robot is submerged and resting on the pool floor, press the power button on the robot. [Icon: Power button symbol]
2. The robot will begin its cleaning cycle, navigating the pool floor and walls.
3. The robot is designed for approximately 180 minutes of runtime on a full charge.

Stopping and Retrieving the Robot

1. To stop the robot, press the power button again.
2. To retrieve the robot, use the included hook or a pool skimmer net. Carefully lift the robot out of the water.
3. Allow excess water to drain from the robot before removing it from the pool area.

[Diagram showing robot placement, operation start, and retrieval would be here.]

Maintenance and Cleaning

Regular maintenance ensures the longevity and efficiency of your WYBOT C2.

Cleaning the Filter Basket

The filter basket should be cleaned after each use or when it appears full.

1. Ensure the robot is switched OFF and disconnected from the charger.
2. Open the robot's housing to access the filter basket. [Icon: Open compartment symbol]
3. Remove the filter basket.
4. Rinse the filter basket thoroughly under running water. Use a soft brush if necessary to remove stubborn debris.
5. Ensure the filter basket is completely dry before reinserting it into the robot.
6. Close the robot's housing securely.

[Diagram illustrating filter basket removal and cleaning.]

Cleaning the Robot Exterior

Wipe the exterior of the robot with a damp cloth. Do not use abrasive cleaners or solvents.

Storage

Store the robot in a cool, dry place, away from direct sunlight. It is recommended to store the robot with a partial charge if storing for extended periods.

Troubleshooting

Refer to the table below for common issues and their solutions.

[Note: If problems persist, contact WYBOT customer support.]

Specifications

Warranty and Support

The WYBOT C2 Intelligent Cordless Pool Robot comes with a limited warranty. Please refer to the warranty card included in the packaging for detailed terms and conditions.

For customer support, troubleshooting assistance, or replacement parts, please contact WYBOT customer service through their official channels or authorized service centers.

[Placeholder for specific contact details or website link if available.]