CYCPLUS AS2 Pro Bicycle Tire Inflator
This document provides instructions for the CYCPLUS AS2 Pro Bicycle Tire Inflator.
Important Warning
For TPU inner tubes with resin valves, ensure they are connected with an extension air hose. Failure to do so may cause the valves to melt due to overheating.
Packing List
- Inflator
- Silicone Case
- Waterproof Bag
- Seal Part
- Hose
- Ball Needle
- Presta Valve Converter
- Cable
Product Details
- Type-C Charging Port
- Nozzle
- LED Screen
- Power Button
- + Button
- − Button
- Pressure Value Display
- Battery Level Indicator
- Pressure Unit Display (PSI/BAR)
Air Nozzle Adaptation
Direct Use
- For Presta Valve: Small hole outward.
- For Schrader Valve: Big hole outward.
For Presta valves, remove the pillar. For Schrader valves, install the pillar.
Use with the Hose
- Connect the hose to the inflator.
- Attach the appropriate adapter to the hose.
- Connect to the valve (Schrader or Presta).
The inflator is ready for Presta valves out of the box. For Schrader valves, adjust the nozzle accordingly. The hose can be directly connected and used, regardless of the presence of a pillar in the nozzle. When the target air pressure is above 100 PSI, it is recommended to use the hose to prevent air leakage from the nozzle.
Operation
1. Connect the Air Valve
A. Connect the nozzle directly to the valve: Adjust the nozzle mode and connect it firmly to the valve. Maintain a tight grip on the nozzle during inflation.
B. Use the hose: Install the hose and the suitable adapter, then connect it to the valve. Using the hose is recommended for Schrader valves.
2. Power On and Set Target Air Pressure
Long-press the Power Button to turn on the device. The screen will illuminate, showing the real-time air pressure reading.
Press the '+' and '-' buttons simultaneously to switch between PSI and BAR units. Use the '+' and '-' buttons to adjust the target pressure. The set pressure will display for 3 seconds before reverting to the current pressure reading.
3. Inflating
Press the Power Button to start inflation. The inflator will automatically shut off when the target air pressure is reached.
4. Shut Down
Long-press the Power Button to turn off the device. If the inflator is not started and no operation is performed within 1 minute while powered on, it will automatically shut down.
Notes
- Fully charge the inflator before first use.
- The inflator may become hot during operation; use the silicone case for protection.
- Press the inflator firmly against the valve before and during inflation. Adjust the position if you hear air leakage until it stops.
- It is normal to feel a slight pulling sensation when removing the inflator from a Presta valve after inflation.
Charging
Charge the inflator using a suitable charger. During charging, the battery indicator light on the screen will illuminate and flash incrementally. When the battery is fully charged, all indicator lights will be illuminated.
Specifications
- Size: 70 x 49 x 28 mm
- Weight: 120 g
- Battery: 420mAh 7.4V 3.11Wh
- Charging Port: Type-C 5V 1.5A
- Current: 2.5 - 7.5 A
- Max Pressure: 120 PSI
Manufacturer Information
- Manufacturer: Chengdu Chendian Intelligent Technology Co., Ltd
- Warranty: Free repair or replacement within one year of purchase.
- After-sales Email: steven@cycplus.com
Certificate of Conformity
Model Name: CUBE Pro (Note: Document title mentions AS2 Pro, but certificate states CUBE Pro. Assuming AS2 Pro is the correct model.)
Product Name: Bicycle Tire Inflator
Implementation Standard: Q/CDZN 001-2023
Inspector: 检01 (Inspector 01)
Status: Inspection qualified, approved for delivery.
Manufacturer: Chengdu Chendian Intelligent Technology Co., Ltd
Disposal Information
Points of collection available at www.quefairedemesdechets.fr.
Prioritize repair or donation of your device!
MADE IN CHINA
