CYCPLUS A2 Smart Tire Inflator
This manual provides comprehensive instructions for the CYCPLUS A2 Smart Tire Inflator.
Product Overview
The CYCPLUS A2 is a smart electric tire inflator designed for various applications including cars, road bikes, mountain bikes, motorcycles, and balls. It features a built-in LED light, power bank functionality, and a clear LED display for pressure readings.
Package Contents
- A. Inflator
- B. Air Tube
- C. Presta Valve Converter
- D. Ball Needle
- E. Type-C Charging Cable
- F. Storage Bag
- G. Bike Mount
- H. Screwdriver
- I. Screw*2
- J. Non-slip Mat
- K. Velcro
- L. User Manual
Product Details
The device features a flashlight, air tube hole, vent port, Type-C charging port, USB output, and an LED screen displaying battery level, pressure value, and unit.
Button Functions
- Power Button: Short press to start/stop inflation, long press to turn on/off the device.
- Unit Button: Short press to cycle through pressure units (PSI, BAR, KPA, kgf/cm²), long press to turn the LED flashlight on/off.
- '+' Button: Increases pressure, quick increase.
- '-' Button: Decreases pressure, quick decrease.
Inflation Guide
| Vehicle Type | Reference Pressure | Inflation Time (from empty) | Frequency (from empty) |
|---|---|---|---|
| Car | 2.3-2.5 BAR | 8-12 min | 2-3 (195 65 R15) |
| Road Bike | 100-120 PSI | 2-3 min | 8-12 (700*23C) |
| Mountain Bike | 30-50 PSI | 2-3 min | 12-18 (26*1.95) |
| Motorcycle | 30-50 PSI | 4-6 min | 4-6 (130 70 R17) |
| Basketball | 7-9 PSI | 0.5-1 min | 30-40 |
Valve Installation
Illustrations show how to connect the air tube and nozzle to Schrader, Presta, and Ball valves.
Operation Steps
- Installation: Connect the air tube to the inflator and then to the valve stem. Use the Presta valve converter for Presta valves and the ball needle for balls.
- Power On: Long press the Power Button until the LED screen lights up, displaying the current pressure.
- Set Target Pressure: Short press the Unit Button to select the desired pressure unit (PSI, BAR, KPA, kgf/cm²). Use the '+' and '-' buttons to adjust the target pressure. The screen will flash twice after you stop setting, then display the current pressure.
- Inflation: Short press the Power Button to start inflating. Press again to pause/continue. The inflator will stop automatically when the target pressure is reached.
- Shutdown: Long press the Power Button to turn off. The device will automatically shut down after 1 minute of inactivity.
- Flashlight: Long press the Unit Button to turn the LED flashlight on/off.
Power Bank Function
Connect your mobile device to the USB output port to charge it. The output is 5V 2A max. The inflator cannot be used as a power bank while it is operating.
Recharging
- Fully recharge the inflator before first use or after prolonged periods of non-use.
- The battery level indicator will flash during charging and remain lit when fully charged.
- Recharge the inflator every three months, even if not in use, to prevent battery damage due to over-discharge.
Attentions
- The inflator may become hot after prolonged use; avoid touching hot parts.
- Inspect the inflator before use. Do not use if any abnormalities are found.
- Stop operation immediately if abnormal sounds or excessive temperatures occur during inflation.
- Ensure smooth airflow by not bending or kinking the air tube.
- Keep the inflator away from flammable and explosive materials as the compressor may produce sparks.
- Do not leave the inflator unattended during operation.
- Allow the inflator to cool down after extended use before using it again.
- Avoid contact with sediment, water, and severe drops.
- Do not use harsh chemicals or cleaning agents for cleaning.
- Do not store in cold, hot, or humid environments.
- Keep out of reach of children.
- Do not inflate air into body orifices or eyes.
- Do not use the inflator while it is charging.
Bike Mount Installation
Instructions and diagrams show how to attach the bike mount to a bicycle, including fixing the mount, applying the non-slip mat, and securing the inflator.
Specifications
- Size: 180*55*53 mm
- Weight: 380g
- Battery: 2600mAh 7.4V 19.24Wh
- Work Current: 1-7A
- Charging Mode: Type-C
- Charging Time: 2 hours
- Max Inflating Pressure: 150 PSI & 10.3 BAR (990 KPA & 10.5 kgf/cm²)
- Storage Temperature: -10℃ to +60℃
- Operation Temperature: 0°C to +40°C
- USB Output: 5V 2A
Factory Information
- Manufacturer: Chengdu Chendian Intelligent Technology Co., Ltd
- Warranty: Free replacement or repair within 2 years of purchase.
- After-sales Email: steven@cycplus.com
Certificate of Conformity
The product, Model A2 Smart Tire Inflator, has been tested and found to be qualified for delivery according to implementation standard Q/CDZN 001-2023. Manufactured by Chengdu Chendian Intelligent Technology Co., Ltd.
